Birko 1040090 User manual

800504 - Birko Pie Warmer- April 2012 v1.02 Page 1 of 12
Pie Warmer
OPERATION MANUAL

Page 2 of 12 800504 - Birko Pie Warmer - April 2012 v1.02
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . .3
Packaging . . . . . . . . . . . . . . . . . . . . . . . .3
Installation. . . . . . . . . . . . . . . . . . . . . . . .3 - 4
Operation. . . . . . . . . . . . . . . . . . . . . . . . .5
Cleaning, Care and Maintenance . . . . . . . 5
Trouble Shooting . . . . . . . . . . . . . . . . . . .6
Technical Specifications . . . . . . . . . . . . .6
Electrical Diagrams . . . . . . . . . . . . . . . . .8
Explosion View. . . . . . . . . . . . . . . . . . . . . 9
Spare Part List. . . . . . . . . . . . . . . . . . . . .10
Compliance . . . . . . . . . . . . . . . . . . . . . . .11
Contact Details . . . . . . . . . . . . . . . . . . . .12

Page 3 of 12 800504 - Birko Pie Warmer - April 2012 v1.02
Introduction
Congratulations on the purchase of your Birko Pie Warmer. Please take a few moments to carefully read through this
manual to ensure the machine is correctly operated and maintained. This will offer the best possible performance from
this product.
Birko will not accept liability for the following if:
*The instructions in this manual have not been followed correctly.
*Non-authorized personnel have tampered with the machine.
*Non-original spare parts are used.
*The machine has not been handled and cleaned correctly.
Packaging
Birko prides itself on quality and service, ensuring that at the time of packaging all products is supplied fully functional
and free of damage.
Provided in this package are the following:
*Pie Warmer
*2 x Sliding Doors
*Rear Glass Pane (glass models only)
*4 x wire racks
*crumb tray
*Manual
Should you find any damage as a result of freight, please contact your Birko dealer immediately.
Installation
A Qualified Service Technician / Engineer should carry out the installation and any repairs if required. Do not remove any
components or service panels on this product.
Before installing this product ensure that all Health & Safety regulations concerning safe positioning, spacing, ventilation,
electrical installation, and fire risk, are complied with.
Local and National Standards must also be consulted in order to comply with the following:

Page 4 of 12 800504 - Birko Pie Warmer - April 2012 v1.02
Health and Safety at Work Legislation
• AS/NZS Codes of Practice
• Fire Precautions
• Wiring Regulations
• Building Regulations
Remove the Pie Warmer from the packaging. Make sure that all protective plastic film and coatings are thoroughly
removed from its surfaces. Please consult the Specification table on page 8 for important information before installing.
Location
• Before locating please check the weights table shown below, then use this information to make sure that the
location chosen can support the weight of the Pie Warmer. Ensure the table/bench is stable.
• Appliances placed on the table when use, it is forbidden to put to the floor.
Electrical Connection
• Supply the appropriate power—(See specifications on page 5). Pie Warmers are supplied with a 3 pin, molded,
with a 10amp plug and lead as standard. The plug is to be connected to a suitable mains socket.
Assembly / Commissioning
• Ensure all packing pieces and protective plastic are removed from the Pie Warmer.
• Rear Glass Pane (glass model only 1040091\1040092). With assistance take the glass pane from the rear outside
of the unit. Angle the glass and slide the glass up and into the top track. One the glass is high enough, level the glass
evenly into the unit and slowly and carefully slides down into the bottom track.
• Wire Racks – Slide the wire racks into the bracket on the inner side of the pie warmer
• Doors. Angle the door and slide the glass up and into the top track. One the glass is high enough, level the glass
evenly into the unit and slowly and carefully slides down into the bottom track. Repeat for the second door.

Page 5 of 12 800504 - Birko Pie Warmer - April 2012 v1.02
Operation
Connect and switch on the power supply, then switch the Pie Warmer on. The Pie Warmer is thermostatically controlled
and is fitted with an indicator light and thermostat for best results. Once the thermostat is set to the desired temperature
the thermostat will cycle on and off to maintain the set temperature. The indicator light is designed to cycle on and off
to indicate when the thermostat is heating or alternatively reached the setting. The thermostats will display the current
temperature within the cabinet.
Cleaning, Care and Maintenance
Switch off the power, and disconnect the Pie Warmer from the power supply. Ensure that the unit is always switched off
and disconnected from the power supply, when cleaning, maintaining or moving.
Safety
The body of the warmer should be wiped down after each day’s operation; however, additional cleaning may be required
depending on frequency of use. The drip tray, wire racks, and glass doors can be removed and washed if necessary.
Care must be taken to allow the Pie Warmer to cool down before cleaning, maintaining or moving, remember stainless
steel and glass can burn.
Do not immerse the Pie Warmer in water, or use jet/pressure washers to clean it.
Warm soapy water is recommended for cleaning. Cleaning agents may cause damage, and leave harmful residues, when
used for a prolonged period on stainless steel.
This appliance is not intended for use by persons (Including Children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
Children should be supervised to ensure they do not play with the appliance.
A Birko dealer or a Recommended Qualified Service Technician should carry out repairs if required.
If the power cord is damaged, it must be replaced by Birko Service Agent or Recommended Qualified Technician in order
to avoid a hazard.

Page 6 of 12 800504 - Birko Pie Warmer - April 2012 v1.02
Trouble Shooting
If your Birko Pie Warmer does not operate, please check the following before placing a service call.
Fault Probable Cause Remedial Action
The unit is not working
the indicator light is
not on
1. Unit is not switched on
Check the unit is plugged correctly and switched
on; be sure to read the operation guide on pages
4 of the instruction manual.
2. Plug and lead is damaged Call service agent or qualified electrician
3. Power supply Check power supply
4. Internal wiring fault Call service agent or qualified electrician
The unit is heating but
the indicator lights are
not on.
The indicator light is faulty Call service agent or qualified electrician
Before calling a service agent or qualified technician:
• Check there is correct power supply.
• The machine is plugged in correctly and power is switched on.
Technical Specifications
Dimensions
Model Height (mm) Width (mm) Depth (mm)
1040090 501 593 359
1040091 501 593 359
1040092 581 753 359
1040093 581 753 359

Page 7 of 12 800504 - Birko Pie Warmer - April 2012 v1.02
Electrical
Model Volts Amps Watts
1040090
230-240V ~
5.43-5.63A 1250-1350W
1040091 5.43-5.63A 1250-1350W
1040092 8.04-8.33A 1850-2000W
1040093 8.04-8.33A 1850-2000W
Weight
Model Net Weight
1040090 20.2 Kg
1040091 20.3 Kg
1040092 25.8 Kg
1040093 26.1 Kg
Capacities
Model Approximate Pie Capacity
1040090 50
1040091 50
1040092 100
1040093 100
Drain Drown
Model
Heat Up Times
90 degrees 160 degrees
1040090 5 mins 11 mins
1040091 5 mins 11 mins
1040092 4 mins 11 mins
1040093 3 mins 9 mins

Page 8 of 12 800504 - Birko Pie Warmer - April 2012 v1.02
Electrical Diagrams
Circuit Diagram
Model: 1040090 /1040091/1040092 / 1040093
The above circuit diagram and principle diagram have been provided to assist qualified technicians. A Recommended
Qualified Service Technician should carry out repairs if needed. Do not remove any components or service panels on this
product.

Page 9 of 12 800504 - Birko Pie Warmer - April 2012 v1.02
Explosion View
Models: 1040090 /1040091 /1040092 /1040093

Page 10 of 12 800504 - Birko Pie Warmer - April 2012 v1.02
Spare Parts List
No. Description Model
1040090
Model
1040091
Model
1040092
Model
1040093
1 Compartment Panel
2 Side Tray
3 Rack 1315071 1315071 1315067 1315067
4 Element 1315075 1315075 1315077 1315077
5 Electrical box
6 Thermostat 1315018 1315018 1315018 1315018
7 Dial 1315070 1315070 1315070 1315070
8 Indicator Light 1315005 1315005 1315005 1315005
9 Tray Recess
10 Tray
11 Heat Exposure Board
12 Front Glass 1315073 1315082 1310611 1315310
13 Vertical Door Recess
14 Door Recess
15 Temperature Meter
16 Feet 1315074 1315074 1315074 1315074
17 Support Bar 1315062 1315062 1315062 1315062
18 Back Baffle 1315177 1315177 1315177 1315177
19 Baffle Recess
20 Rubber Coil
21 Back Panel 1310612 1315064 1310613 1315311
22 Plug & Lead 1315011 1315011 1315011 1315011

Page 11 of 12 800504 - Birko Pie Warmer - April 2012 v1.02
Compliance
Birko products have undergone strict product testing in order to comply with regulatory standards and specifications set
by international, independent, and federal authorities.
As testimony to such compliance, Birko products carry the following marks/symbols:

Page 12 of 12 800504 - Birko Pie Warmer - April 2012 v1.02
Contact Details
Head Office:
Birko Heaters Australia Pty Ltd.,
ABN 39 103 881 625 67 Allingham St
Condell Park
N.S.W. 2200
AUSTRALIA
Local Ph: 1300 724 955
Local Fax: [phone]
[email protected]
www.birkoheaters.com
The term ‘Birko’ is a registered trade mark of Birko Heaters Australia Pty Ltd.
Zenith Heaters Limited, IRD No. 95 640 729
Unit 2/15 Moselle Avenue, Henderson.
Auckland. 0610
NEW ZEALAND.
Telephone: [phone]
Facsimile: 0800 559055
www.zenithheaters.co.nz