Bissell 3590 8990 3591 User manual

Safety Instructions
Product View
Assembly
Operations / Special Tools
CleanView™
BAGLESS
USER’S GUIDE
3590/3591/8990 SERIES
3
4
4-5
6-8
Maintenance
8-11
Troubleshooting
12
Warranty
14
Consumer Services
13
Replacement Parts
13
Reorder Form
15

2
Thanks for buying a BISSELL CleanView™
We’re glad you purchased a BISSELL CleanView Vacuum. Everything
we know about floor care went into the design and construction of this
powerful, high-tech home vacuuming system.
Your BISSELL CleanView is well made, and we back it with a
limited comprehensive one-year warranty. We also stand behind it with a
knowledgeable, dedicated Consumer Services department, so, should you
ever have a problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today,
BISSELL is a global leader in the design, manufacture, and service of high
quality homecare products like your BISSELL CleanView.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
President and Chief Executive Officer

3
IMPORTANT SAFETY INSTRUCTIONS
■Keep hair, loose clothing, fingers, and all
parts of body away from openings and
moving parts.
■Turn off all controls before plugging or
unplugging vacuum cleaner.
■Use extra care when cleaning stairs.
■ Do not pick up flammable materials (lighter
fluid, gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapors.
■Do not pick up toxic material (chlorine
bleach, ammonia, drain cleaner, etc.).
■Do not use vacuum cleaner in an enclosed
space filled with vapors given off by oil
base paint, paint thinner, some moth
proofing substances, flammable dust, or
other explosive or toxic vapors.
■Do not pick up hard or sharp objects such
as glass, nails, screws, coins, etc.
■Do not pick up anything that is burning
or smoking, such as cigarettes, matches, or
hot ashes.
■Do not use without filters in place.
■Use only on dry, indoor surfaces.
■Keep appliance on a level surface.
■Do not carry the vacuum cleaner while it
is running.
SAVE THESE INSTRUCTIONS
FOR FUTURE USE.
When using an electrical appliance,
basic precautions should be observed,
including the following:
READ ALL INSTRUCTIONS
BEFORE USING YOUR
UPRIGHT VACUUM.
Always connect to a polarized outlet (left slot is
wider than right). Unplug from outlet when not
in use and before conducting maintenance.
WARNING: To reduce the risk of
fire, electric shock, or injury:
■Do not modify the polarized plug to fit a
non-polarized outlet or extension cord.
■Do not leave vacuum cleaner unattended
when it is plugged in.
■Unplug from outlet when not in use and
before servicing.
■Do not use outdoors or on wet surfaces.
■Do not allow children to operate vacuum
cleaner or use as a toy.
■Close attention is necessary when used by
or near children.
■Do not use for any purpose other than
described in this User’s Guide.
■Use only manufacturer’s recommended
attachments.
■ Do not use with damaged cord or plug.
■If appliance is not working as it should,
has been dropped, damaged, left outdoors,
or dropped into water, have it repaired at
an authorized service center.
■Do not pull or carry by cord, use cord as a
handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run
appliance over cord. Keep cord away from
heated surfaces.
■Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
■Do not handle vacuum cleaner or plug with
wet hands.
■Do not put any object into openings. Do
not use with any opening blocked; keep
openings free of dust, lint, hair, and
anything that may reduce air flow.
THIS APPLIANCE HAS A
POLARIZED PLUG.
To reduce the risk of electric shock, this
appliance has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized
outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install a proper
outlet. Do not change the plug in any way.
This model is for household use only.

4
CAUTION:
Do not plug in your vacuum
cleaner until you are familiar
with all instructions and
operating procedures.
Power
Switch
Carrying
Handle
Crevice Tool
Post-Motor
Filter
Quick Reach
Handle
Handle
Quick Release
Cord Wrap
Handle
Release
Pedal
Powerfoot
Stretch Hose
Extension Wand
Power Cord
Furniture
Protection
Guard
Height
Adjustment
Knob
Upper Tank
Dirt Container
Pre-Motor Filter
Lock ’n
Seal™Lever
Headlight
Dusting
Brush Hose Wand
Upper Tank Knob
Hose Clip
Power Trak™
Furniture
Protection Guard
CleanView
Window
Optional Hepa
Media Filter (Select
Models Only)
Power Trak™Models
Hose
Wand Base
Louvers

5
This User’s Guide has been designed to help you get the
most satisfaction from your BISSELL CleanView. You’ll find
assembly and operating instructions, safety precautions, as well
as maintenance and troubleshooting instructions. Please read
this Guide thoroughly before assembling your vacuum cleaner.
Pay particular attention to the product diagram, assembly
instructions, and part names. Locate and organize all parts
before assembly. Familiarize yourself with the parts and where
they fit. Following this User’s Guide will greatly enhance your
ability to get the most performance from your BISSELL
CleanView for many years.
The only tool you’ll need to assemble your vacuum
cleaner is a screwdriver.
Locate the vacuum Handle and remove the screw packet
taped to the base of the Handle.
Stand the vacuum upright and slide the base of the Handle
firmly into the grooves at the top of the vacuum body.
Check to be sure the Handle is fitted to the vacuum
body. If there is a gap in front, continue to push firmly
until the Handle is flush.
Insert one screw provided from the screw packet into the
existing hole. Tighten securely with a screwdriver.
Position the Hose Assembly on the back of the vacuum
as shown.
Attach the Hose with the remaining two screws from
the packet. Tighten securely with a screwdriver.
Grasping the Quick Reach Handle, slide the end of the
Hose Wand onto the suction intake opening. Snap the
Hose into the Hose Clip.
NOTE: The Powerfoot will not operate effectively
unless the hose wand is firmly attached to the
suction intake opening.
How To Use This Guide
How To Put It Together WARNING:
Plastic film can be dangerous.
To avoid danger of suffocation,
keep away from babies
and children.
Attach Handle To Vacuum
1.
2.
3.
4.
Attach Vacuum Hose and Tools
1.
2.
3.

6
Slide the Extension Wand and the Crevice Tool together
into the storage clip as shown.
Slide the Dusting Brush Tool into the storage clip as shown.
Press the Handle Release Pedal with your foot to place
your CleanView into one of three cleaning positions.
Upright- For storage and above floor cleaning with tools.
Normal Cleaning- Press Handle Release Pedal once. Use
for most household floor cleaning tasks.
Low Cleaning- With the vacuum in normal cleaning position,
press Handle Release Pedal again. Use for reaching under
low furniture such as tables, chairs or beds.
The Powerfoot/Rotating Floor Brush on your BISSELL CleanView
can be adjusted to clean several floor surfaces.
NOTE: For optimal cleaning performance, adjust
to the lowest practical setting. If your cleaner is
difficult to push, adjust to the next higher setting.
Place Handle in Upright Position.
Turn Height Adjustment knob to desired setting.
Lowest Setting - For bare floors.
Medium Settings - For short and medium
pile carpets.
Highest Setting - For plush pile carpet.
Place the Handle into the Normal Cleaning Position and
the Powerfoot will adjust to the setting chosen.
NOTE: You may also adjust the setting while in
the Normal Cleaning Position.
How To Use Your BISSELL CleanView
Handle Positions
1.
2.
3.
Tip:
Your BISSELL
CleanView
features a
Quick-Release
Cord Wrap. To
remove the
Power Cord
quickly and
easily, rotate the
Upper Cord Wrap
towards floor,
and slip Power
Cord from Upper
and Lower
Cord Wraps.
Tip:
Before cleaning
under low
furniture, check
area first for
objects that
might harm the
unit or block the
Vacuum Hose.
Power Height Adjustment
1.
2.
CAUTION:
Before using your vacuum, make
sure that the Dirt Container and
Upper Tank are in locked position
and that both filters (Pre-Motor
and Post-Motor) are in place. Do
not operate your vacuum without
these filters.
3.
Attach Vacuum Hose and Tools Continued
4.
5.
1
2
3
Note:
The Floor Brush will continue to rotate
while you use your vacuum for above
floor cleaning. To prevent carpet damage,
do not lean on the vacuum or let the
Powerfoot tilt forward.

7
To move your cleaner from room to room, put the Handle
in the upright position, tilt the cleaner back on its rear
wheels and push forward.
The cleaner can also be moved by using the
Carrying Handle.
Your BISSELL CleanView is not only a powerful carpet and rug
vacuum cleaner, it’s also a versatile above floor vacuum cleaner
when you select one of the special tools.
Raise Handle to Upright Position.
Grasp the Quick Reach Handle and lift Hose Wand to
separate from suction intake opening.
Attach tools by firmly pushing onto Vacuum Hose
or Extension Wand.
Dusting Brush Tool:
Use to dust furniture, blinds, books, lamps, shelves,
draperies, cushions.
Crevice Tool:
Use in tight narrow spaces.
Extension Wand:
Use with desired attachment for a longer reach.
Special On-Board Tools
Transporting Cleaner
1.
2.
1.
2.
3.
Tip:
Hair, string and
small objects can
block the Vacuum
Hose or Tools.
Check them
occasionally for
obstructions.
CAUTION:
The Rotating Floor Brush continues to rotate
while tools are in use. To reduce the risk of
injury from moving parts, always move the
cleaner with the Carrying Handle at the back
of the cleaner. Always place vacuum cleaner
on floor with Handle in Upright position when
using tools. Never place your fingers under
the cleaner when it is running. Never place
Powerfoot on furniture or uneven surfaces.
Do not place vacuum cleaner close enough
to objects to pull them into rotating brush.
Carrying
Handle
Note:
The Floor Brush will continue to rotate
while you use your vacuum for above
floor cleaning. To prevent carpet damage,
do not lean on the vacuum or let the
Powerfoot tilt forward.

8
When you are done using your BISSELL CleanView, return it to the
Upright position and store the Power Cord.
Turn vacuum cleaner off.
Unplug Power Cord by grasping the polarized plug (NOT
the cord) and disconnect from outlet.
Loop Power Cord around Cord Wraps on side of
vacuum cleaner.
Clip molded plug to Power Cord to secure.
To maintain maximum cleaning performance, the follow-
ing maintenance steps must be performed:
Empty the Dirt Container when the dirt reaches the
“Full” line on the side.
Clean or replace the Pre-Motor Filter at least once a
month.
Clean or replace the Post-Motor Filter every three
months.
More frequent filter cleaning may be necessary if you are
vacuuming new carpet, fine dust, or have allergy con-
cerns. Follow the instructions on the following pages to
perform these simple maintenance steps.
The Dirt Container needs to be emptied when the dirt
reaches the Full line on the side of the Container.
Unplug cleaner from electrical outlet.
Slide the Lock ‘n Seal Lever to the "Unlock" position.
Grasp handle and pull the Dirt Container straight out to
remove from vacuum.
Empty dirt into garbage container.
Put the Dirt Container back in the vacuum and slide the
lever to the "Lock" position.
Note: The Dirt Container may be washed in warm
water with a mild detergent. Make sure it is com-
pletely dry before using again.
How to Maintain Your BISSELL CleanView
Tip:
For maximum
cleaning performance,
Check and clean or
replace all filters
as suggested.
WARNING: To
reduce the risk of electric
shock, turn Power Switch
OFF and disconnect
polarized plug from
electrical outlet before
performing maintenance or
troubleshooting checks.
Power Cord Storage
1.
2.
3.
4.
NOTICE:
While vacuuming, certain
carpets and low humidity
conditions may generate small
static discharges. The discharges
are entirely harmless and are
not associated in any way with
the main power supply.
Empty Dirt Container
1.
2.
3.
4.
5.
Full Line
Lock Position
Unlock
Position
1.
2.
3.

9
Unplug the cleaner from electrical outlet.
The Upper Tank area can be reached by removing the
Dirt Container, reaching underneath the Upper Tank and
turning the Louver Cap to unlock. Pull straight down to
remove. Brush the dirt off the Louvers and Upper Tank
area.
The Upper Tank and Louvers may also be wiped clean
with a damp cloth.
Note: For easier access, the entire Upper Tank
may be removed by turning the knob on the
back of the cleaner to unlock and pulling the
entire tank straight out.
Use only BISSELL Replacement Filters in your BISSELL CleanView.
Pre-Motor Filter 203-2056
Post-Motor Filter 203-1009
HEPA Media Post-Motor Filter 32076 (Select Models Only)
Unplug the cleaner from electrical outlet.
The Pre-Motor Filter protects the motor from dirt particles.
It is located in the slide out tray underneath the Dirt
Container. If the filter becomes dirty, pull out the tray, lift
out the filter and clean.
The Post-Motor Filter assists in the filtration process to
return clean air to the room. It is located behind the door
on the side of the cleaner. If the filter becomes dirty,
open the door, remove the filter and clean.
Note: Select Models come with a white, pleated
HEPA Media Filter. This filter is not washable and
must be replaced.
The standard filters may be hand washed in cold water
with mild detergent. Rinse well and air dry thoroughly
before replacing.
Cleaning The Upper Tank & Louvers
1.
2.
3.
WARNING:
Do Not operate cleaner
with damp or wet
filters or without all
filters in place.
Cleaning The Pre-Motor and Post-Motor Filters
1.
2.
3.
4. WARNING:
To reduce the risk of injury
from moving parts, turn
off vacuum cleaner and
disconnect Power Plug
from electrical outlet.
Post-Motor
Filter
Pre-Motor
Filter

10
You should check your vacuum cleaner’s Rotating Floor Brush
and Drive Belt regularly for wear or damage. You should also
clean the brush and brush ends of strings, hair, and carpet
fibers. These can wrap around the brush and hamper its ability
to effectively clean your carpet. Also remove any debris that
has accumulated under the brush cover.
Unplug cleaner from electrical outlet.
Place handle in Low position and turn vacuum cleaner
over so bottom side is up.
Remove the four screws as shown with a Phillips head
screwdriver. Lift the Brush Cover off.
Note: The Power Trak models have an additional
screw which needs to be removed. See the 2nd
Illustration.
Grasp Rotating Floor Brush at both ends and lift.
Clean strings, hair and other debris from Rotating Floor
Brush, paying particular attention to brush ends.
Clean strings, hair and other debris from Motor Pulley
and Drive Belt areas.
Check Drive Belt carefully for wear, cuts or stressed areas.
Check Air Passageway for obstructions. Remove debris
from this area.
Use only BISSELL Style 7 Replacement Belts (#32074) in your
BISSELL CleanView.
Unplug cleaner from electrical outlet.
With Rotating Floor Brush removed from vacuum cleaner
(Steps 1-4 of check Rotating Floor Brush and Drive Belt),
grasp old Drive Belt and remove from Motor Pulley.
Discard old Drive Belt.
Place new Drive Belt over Motor Pulley and stretch other
end over Rotating Floor Brush in the space between
the bristles.
Place ends of Rotating Floor Brush down into slots on
sides as shown.
Turn Rotating Floor Brush by hand several times in the
direction of Motor Pulley. If properly installed, Drive Belt
will center itself on Rotating Brush crown.
Reposition Brush Cover and screws. Tighten
screws securely.
Check Rotating Floor Brush and Drive Belt
5.
6.
7.
8.
1.
2.
3.
4.
5.
6.
Replace Drive Belt
1.
2.
3.
4.
Brush
Cover
Air Passageway
Motor Pulley
Power Trak models only

11
Use only BISSELL Replacement Bulb (#203-1007) in your BISSELL CleanView.
Unplug cleaner from electrical outlet
Using a screwdriver, remove the two screws as shown and lift off the lens.
Remove the bulb from the socket by pushing in gently and turning it
counterclockwise. Install the new bulb by pushing it gently into the
socket and turning clockwise.
Reposition lens and secure with the two screws.
Low suction or poor pickup may be due to a clog in the vacuum cleaner. If
you notice a change in the sound of the motor or a reduction in the spinning
action, check for clogs.
Unplug cleaner from electrical outlet.
Empty Dirt Container.
Check Upper Tank for build up or clogs.
Remove the Upper Tank and check the suction inlet for a clog.
Grasp the Quick Reach Handle and lift Hose Wand to separate from
the suction opening. Check for a clog in the Base, the Wand or
the Hose.
Remove the screw attaching the Hose Wand Base to the
vacuum. Straighten the Hose Wand Base and unclog with long,
narrow object.
If the clog persists, follow the instructions for Checking the
Rotating Floor Brush on page 10 and inspect the Air Passageway
for obstructions.
An internal thermal protector has been designed into your cleaner to
protect it from overheating. When the thermal protector activates, the
cleaner will stop running. If this happens, proceed as follows:
Turn the cleaner OFF and unplug from electrical outlet.
Check the Upper Tank area, Pre-Motor Filter and
Post-Motor Filter for dirt accumulation.
Refer to the "Clearing Clogs" section.
When cleaner is unplugged and motor cools for approximately
30 minutes, the thermal protector automatically resets and clean-
ing may continue. If the thermal protector continues to activate after
following the above steps, your cleaner may need servicing. Call
BISSELL Consumer Services, or visit the website.
Replace Lightbulb
1.
2.
3.
4.
Clearing Clogs
1.
2.
3.
4.
5.
6.
Suction
Inlet
Thermal Protector
1.
2.
3.
4.
Air Passageway
7.

Vacuum cleaner won't run.
Possible Causes Remedies
Power cord not firmly plugged in Check electrical plug
Blown household fuse or breaker Check/replace fuse - Reset breaker
Thermal protector activated Allow cleaner to cool for 30 minutes, see pg. 12
Vacuum cleaner won't pick up dirt.
Possible Causes Remedies
Incorrect Height Adjustment Adjust Powerfoot to correct height setting
Hose not attached to suction opening Grasp Quick Reach Handle and firmly push Hose
Wand onto the suction opening
Crack or hole in Hose Check Hose and replace if needed
Broken or worn Drive Belt Replace Drive Belt, see pg. 10-11
Rotating Floor Brush bristles worn Replace brush
Rotating Floor Brush jammed Remove brush and clean debris from brush ends
Clog in vacuum Follow instructions on pg. 12 for clearing clogs
Dirt Container full Empty Dirt Container
Dirt Container or Upper Tank not installed properly Position correctly and lock in place
Filters are dirty Check and clean Pre-Motor and
Post-Motor Filters
Tools won't pick up dirt.
Possible Cause Remedies
Crack or hole in Hose Check Hose and replace if needed
Clog in vacuum Follow instructions on pg. 12 for clearing clogs
Dirt Container full Empty Dirt Container
Dirt Container or Upper Tank not installed properly Position correctly and lock in place
Filters are dirty Check and clean Pre-Motor and
Post-Motor Filters
Vacuum cleaner is difficult to push.
Possible Causes Remedies
Incorrect Height Adjustment Adjust Powerfoot to correct height setting
Visible dirt escaping from cleaner.
Possible Causes Remedies
Dirt Container full Empty Dirt Container
Filters missing or installed incorrectly Check Pre-Motor and Post-Motor
Filters for correct installation
Dirt Container installed incorrectly Pull out and re-insert Dirt Container correctly
If suggested solutions do not correct the problem, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. — 9 p.m. ET
Saturday 9 a.m. — 5 p.m. ET
or visit the BISSELL website - www.bissell.com
12
1
2
3
1
2
3
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
1
2
3
4
5
11
11
22
Troubleshooting
WARNING:
To reduce the risk of injury
from moving parts and/ or
electrical shock, turn
Power Switch OFF and
disconnect polarized plug
from electrical outlet
before performing
troubleshooting checks.
33

13
For information about repairs or replacement parts, or
questions about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. — 9 p.m. ET
Saturday 9 a.m. — 5 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids, MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It is your warranty.
BISSELL Consumer Services
Item Part No. Part Name
1 32074 Style 7 Drive Belt (2-Pack)
2 203-1007 Headlight Bulb
3 203-1063 Crevice Tool
4 203-1083 Dusting Brush
5 203-1084 Extension Wand
6 203-1036 Vacuum Hose
7 203-2012 Vacuum Hose Clear (Select Models Only)
8 203-1016 Brush Roll
9 203-2013 Power Trak Brush Roll (Select Models Only)
10 203-2056 Pre-Motor Filter
11 203-1009 Post-Motor Filter
12 32076 HEPA Media Post-Motor Filter (Select Models Only)
Replacement Parts – BISSELL CleanView Series
You may purchase replacement parts from your retailer, by using the order
form in this User’s Guide, by calling BISSELL Consumer Services or by
visiting our website. To locate a retailer near you, or to place an order using
Visa, MasterCard, Discover or American Express, call
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. — 9 p.m. ET
Saturday 9 a.m. — 5 p.m. ET
Or visit our Website - www.bissell.com
1 2
3 4
5 6/7
8 9
©2002 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in Korea.
Part Number 010-6045
Rev 9/02
Visit our website at:
www.bissell.com
12
11
10

14
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to
state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please
contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare,
Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of charge
from the date of purchase by the original purchaser, for one year any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This warranty does not
apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused
by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is not
covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your warranty, contact
BISSELL Consumer Services.
Website or E-mail:
www.bissell.com
Use the “Customer Services” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 9 p.m. ET
Saturday 9 a.m. - 5 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
NATURE
ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE
PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY
IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION
FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Warranty

15
BISSELL CleanView Order Form
Order Information
Item Part No. Part Name Qty. x Unit = Total
Price
1 32074 Style 7 Drive Belt (2 pack) ______ $2.99 ______ ______
2 203-1007 Headlight Bulb ______ $1.95 ______ ______
3 203-1063 Crevice Tool ______ $2.99 ______ ______
4 203-1083 Dusting Brush ______ $1.70 ______ ______
5 203-1084 Extension Wand ______ $1.50 ______ ______
6 203-1036 Vacuum Hose ______ $8.50 ______
7 203-2012 Vacuum Hose Clear
(Select Models Only) ______ $9.50 ______ ______
8 203-1016 Brush Roll ______ $15.95 ______ ______
9 203-2013 Power Trak Brush Roll
(Select Models Only) ______ $17.95 ______ ______
10 203-2056 Pre-Motor Filter ______ $1.50 ______ ______
11 203-1009 Post-Motor Filter ______ $2.95 ______ ______
12 32076 HEPA Media Post-Motor
Filter (Select Models Only) ______ $9.99 ______ ______
SUB TOTAL ______
Sales tax based on delivery address Shipping ______
AR, AZ, CA, FL, GA, IL, KS, MA, MD, MI, MN, MO,
NC, NE, NJ, NY, OH, PA, TN, TX, UT and WA
residents add applicable sales tax. Sales Tax ______
Price applicable in continental United States only
Price subject to change without notice Order Total ______
Billing Information
Charge: Mastercard Enclosed in your envelope
check or money order
Visa payable to BISSELL Homecare, Inc.
(No cash or stamps please)
American Express
Discover
Telephone ________________________________________________________
Account
Number
(include all digits)
Card
Expires
Month Year Signature __________________________________
Or visit BISSELL website - www.bissell.com
1
2
Shipping Information
Ship To ____________________________
Address ____________________________
____________________________
City ____________________________
State ____________ Zip____________
3
MAIL REORDER FORM TO:
BISSELL Homecare Inc.
Mail Order Department
PO Box 3606
Grand Rapids MI 49501
OR FAX TO:
1-616-791-7711
Shipping and Handling
.01 to $4.99 = $2.95
$5.00 to $19.99 = $4.95
$20.00 to $99.99 = $7.95
$100.00 to $229.99 = $13.95
$230.00 and up = $25.95
UPS 2nd Day = above shipping amount + $5.75
UPS Next Day = above shipping amount + $19.95
✁