Bixby L-GZ399PAL-1 User manual

Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to finish. The
final product will be a quality piece that will go together smoothly and give years of enjoyment.
All you will need is a screwdriver, a hammer and ladder (not included) whose height is no less than 2.5m.
Item Identification: For ease of identification, all parts are labeled to correspond to the Step number in which
the part is used.
Assembly Instructions
10'x12' Bixby gazebo
Item: L-GZ399PAL-1

Short panel (1) A1 2
Short panel (2) A2 2
Long panel (1) B1 2
Long panel (2) B2 2
Slanting bar of big top C 4
Long mid top bar D1 2
Short mid top bar D2 2
Small top bar E 4
Slanting bar connector F 4
Mid top bar connector G 4
Big top connector H 1
Small top connector I 1
Conner decor block J 4
Post K 4
Post base L 4
Base protector M 4
Long netting bar N1 4
Short netting bar N2 4
Top Finial O 1
Pothook P 1
Small canopy Q 1
Large canopy R 1
Wall S 1
Mosquito netting T 1
Parts List

Hardware Pack 1
Fig.1: Fit the Base protector (M) onto the Post (K), connect the Post base (L) and post (K) by using bolt
(AA) and flat washer (BB).
Fig.2: Fix the Conner decor block (J) & Slanting bar connector (F) onto the top of the post (K) by using bolt
(AA) and flat washer (BB).
Fig.3: Insert the Short panel 1 (A1) into the short panel 2 (A2), fix them by using bolt (CC) and flat washer
(BB), then fix the Mid top bar connector (G) on the middle of the A1 & A2. (Connect the long panels (B1 &
B2) and Mid top bar connector (G) in the same way.)
AA 1/4"-20*0.6 bolt 44 PCS
BB Φ1/4" washer 76 PCS
CC 1/4"-20*0.6 bolt 16 PCS
DD 1/4"-20*1 bolt 16 PCS
W 1/4"- wrench 1 PC

Fig.4: Fix the netting bar (N1 & N2) to the panels by using bolt (AA) and flat washer (BB).
Fig.5: Fix the assembled panels to the post (K) by using bolt (DD) and flat washer (BB).
Hardware Pack 2
Fig.6: Insert the Slanting bar of big top (C) into the Slanting bar connector (F).
Fig.7: Attach the Pothook (P) onto the Big top connector (H), insert the Slanting bar of big top (C) & mid top
bar (D1&D2) into the Big top connector (H).
Fig.7-1: Insert the mid top bar (D1，D2) into the Mid top bar connector (G). Put the Large canopy (R) on
the big top; do not spread it.
Fig.8: Insert the Small top bar (E) into the Small top connector (I).
BB Φ1/4" washer 4 PCS
EE 1/4"-20 hex nut 4 PCS
FF 1/4"-20*1.4 bolt 4 PCS

Hardware Pack 3
Fig.8-1: Place the Small canopy (Q) on the small top and tighten, then screw the Top Finial (O) onto the
Small top connector (I).
Fig.9: Install the assembled small top on the Slanting bar of big top (C) by using bolt (FF), flat washer (BB)
and nut (EE).
GG Plastic Ring 104 PCS
HH Φ5/16"*7 peg 16 PCS
JJ Touch up paint 1 PC

Fig.10: Spread the Large canopy (R), hang the pothooks of the large canopy into the holes on the panels.
Fig.11: Hang Mosquito netting (T) on the inside netting bar (N1 & N2) by using the Plastic ring (GG), hang the
Wall (S) on the outside netting bar in the same way.
Fig.12: Lift the Base protector (M), fix the assembled gazebo with Peg (HH).
Now, your Gazebo is ready for use.
IMPORTANT:
1. When assembling and using this product, basic safety precautions should always be followed to reduce the
risk of personal injury and damage to equipment. Please read all instructions before assembly and use.
2. Some parts may contain sharp edges, wear protective gloves if necessary. At least five or more people are
recommended for safe assembly.
3. Keep all children and pets away from assembly area.
4. At least 6 feet from any obstruction such as fence, garage, house, overhanging branches, laundry line or
electrical wires.
5. Do not use the unit during an electrical storm, as there is a remote chance of getting struck by lightening.
6. Do not leave the gazebo assembled when there is a risk of high wind, as possible damage will occur to the
structure. Remove fabric roof and secure screen & privacy panels to poles.
7. Install on level surface.
8. Never barbecue under this gazebo or use lanterns that have open flames.
9. This package contains small items and plastic bags that should be kept away from children.
10. Check all nuts and bolts for tightness before and during usage. Ensure that all connectors and poles are
firmly secured in position fully. It is important to do so before use so as to avoid a possible collapse or damage
to the item, which could also result in injury.
11. This gazebo is intended for decorative and sunshade purposes only and is not meant to withstand
extreme weather conditions including high winds, torrential rain and snow. Gazebo fabric is water resistant,
not water proof and may leak during exposure to precipitation.
WARNINGS:
1. Assembly Instructions must be followed.
2. Pegs supplied must be used to hold this gazebo in place when upright.
3. Warranty does not cover damage due to extreme weather conditions.
WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC.
This tent meets the flammability requirements of CPAI-84. The fabric may burn if left in continuous contact
with any flame source. The application of any foreign substance to the tent fabric may render the
flame-resistant properties ineffective.
This unit is heavy. Do not assemble this item alone.
LIMITED WARRANTY:
This limited warranty is extended to the original purchaser and applies to defects in materials and
workmanship of your item provided the item is maintained with care and used only for personal, residential
purposes.
The item is warranted to be free from defects in material or workmanship for a period of 1 year. If any defect is
found, please call our customer service department at 1-866-578-6569 for help. The manufacturer will not
cover transportation or delivery costs, or compensate the individual or any outside party for assembling or
disassembling the product. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Please do not return this product to the store. For technical assistance on assembly or
replacement parts call Sunjoy Industries at 1(866) 578-6569 from 8:30 AM to 5:30 PM EST or
Email [email protected] or visit www.sunjoygroup.com to place your order or fax your
parts replacement order form together with your purchase receipt to 1 [phone] for
assistance.
Made in China