Black & Decker Spacemaker CO100 Installation instructions


Models
Modelos
❑
CO100
❑
CO100WM
❑
CO100B
❑
CO95
USA/Canada 1-800-231-9786
www.prodprotect.com/applica
Accessories/Parts (USA/Canada)
Accesorios/Partes (EE.UU/Canadá)
1-800-738-0245
PleaseReadandSavethisUseandCareBook
Porfavorleaesteinstructivoantesdeusarelproducto
UNDER-THE-CABINET
CAN OPENER
ABRELATAS
PARA INSTALAR DEBAJO DEL GABINETE
Register your product online at
www.prodprotect.com/applica, for a chance to
WIN $100,000!
For US residents only
Registre su producto por Internet en
www.prodprotect.com/applica y tendrá la oportunidad
de GANAR $100,000!
Solamente para residentes de EE.UU
™
†



IMPORTANTSAFEGUARDS
When using electrical appliances, basic safety precautions should always
be followed, including the following:
❑ Read all instructions.
❑ To protect against risk of electrical shock do not immerse cord, plugs or
appliance in water or other liquid.
❑ Close supervision is necessary when any appliance is used by or near
children.
❑ Make sure appliance is OFF when not in use, before putting on or taking
off parts, and before cleaning.
❑ Avoid contacting moving parts.
❑ Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or is dropped or damaged in any
manner. Return appliance to the nearest authorized service facility for
examination, repair or electrical or mechanical adjustment. Or, call the
appropriate toll-free number on the cover of this manual.
❑ The use of attachments not recommended or sold by the manufacturer
may cause fire, electric shock or injury.
❑ Do not use outdoors.
❑ Do not open pressurized (aerosol-type) cans.
❑ Do not open cans of flammable liquids such as lighter fluids.
❑ To reduce the risk of fire or electric shock, do not operate any heating
appliance beneath the mounted unit.
❑ Do not mount the storage bracket/unit over or near any portion of a
heating or cooking appliance, or a sink or basin.
SAVETHESEINSTRUCTIONS.
Thisproductisforhouseholduseonly.
POLARIZEDPLUG(0VModelsOnly)
This appliance has a polarized plug (one blade is wider than the other). To reduce the
risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If
the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician. Do not attempt to modify the plug in any way.
TAMPER-RESISTANTSCREW
Warning:Thisapplianceisequippedwithatamper-resistantscrewtoprevent
removaloftheoutercover.Toreducetheriskoffireorelectricshock,donot
attempttoremovetheoutercover.Therearenouser-serviceablepartsinside.
Repairshouldbedoneonlybyauthorizedservicepersonnel.
ELECTRICALCORD
a) A short power-supply cord (or detachable power-supply cord) is to be provided
to reduce the risk resulting from becoming entangled in or tripping over a
longer cord.
b) Longer detachable power-supply cords or extension cords are available and
may be used if care is exercised in their use.
c) If a long detachable power-supply cord or extension cord is used,
1) The marked electrical rating of the detachable power-supply cord
or extension cord should be at least as great as the electrical rating of the
appliance,
2) If the appliance is of the grounded type, the extension cord should be
a grounding-type 3-wire cord, and
3) The longer cord should be arranged so that it will not drape over the
countertop or tabletop where it can be pulled on by children or
tripped over.
Note:If the power supply cord is damaged, it should be replaced by qualified
personnel; in Latin America, by an authorized service center.



Productmayvaryslightlyfromwhatisillustrated.
 . Bagcutter
 . Knifesharpener
 . Bottleopener
 . Cover
† . Bladeassemblywithmagnet(Part#CO00)(White),(Part#CO00)(Black)
 6. Locatingpost
 7. Piercinglever
 8. Cordstorage(notshown)
 9. Cordmanagementhook(notshown)
†0. MountingKit(Part#CO00-0)White,(Part#CO00-0)Black(notshown)
Note:†indicates consumer replaceable/removable parts







A
†. MountingParts
  (Part#SDC-MOUNTINGKIT)
  A.6Spacers
   ½"
   ¼"
   /6"
   /6"
  B.Screws
   "
   ½"
   ¼"
  C.Washers
 . MountingTemplate(inbox)
Youwillalsoneed:
• Tape
• Ruler(oryoumaycutouttherulerprovidedonthetemplate)
• Electricdrillwitha¼”drillbit
A
A
C
B

6
7
Note: If you are connecting this appliance to the receptacle of another
†SpaceMaker™ appliance such as the toaster oven or coffeemaker, make sure you
can easily unplug the appliance following use.
DETERMINECABINETTYPE
Prior to installation, determine if your cabinet has a flat bottom (B) or an
overhang molding (C). If your cabinet is flat, follow STANDARD INSTALLATION;
if the cabinet has an overhang molding, refer to OVERHANG MOLDING
INSTALLATION.
STANDARDINSTALLATION(FLATCABINET)
Important:Alwayswearprotectiveglassesorgogglestopreventinjurywhen
drilling.
1. Clear countertop under installation area to avoid getting dust or debris on other
appliances or items. Open cabinets and remove contents to make mounting
easier.
2. Clean both the underside and topside of the bottom panel of the cabinet.
3. With cabinet doors open, place mounting template flush against the surface of
the underside of your cabinet, making sure to align thick line on template with
bottom front edge of your cabinet (D).
Important:Donotalignscrewholesontemplatedirectlyunderthepartition
betweencabinets,asthiswillpreventyoufrominstallingtheapplianceproperly.
Paycloseattentiontowherethedrillholeswillbesetsoasnottodamageyour
cabinetsduringmounting.Drillingthroughyourcabinet’spartitionmaycause
damagetocabinetsandpreventproperinstallation.
4. Fold the template along the edge of your cabinet so the thick line is straight
with bottom front edge; pull template tight and tape down to hold in place.
GETTINGSTARTED
• Remove all packing material, labels and any stickers.
• Remove and save literature.
• Unpack mounting parts and set them aside in a safe place where they will not
roll away or get lost.
Important:Donotattempttooperateapplianceuntilitisproperlyinstalled.
CHOOSEALOCATION
When choosing your location, consider the following:
• DO make sure to mount within reach of an electrical outlet.
• DO consider your normal work patterns in the kitchen when choosing
location.
• DONOT mount over any heating or cooking appliance such as your range or
oven.
• DONOT mount over or near a sink.
• DONOTmount under, in front of or behind any under-cabinet light fixtures.
Note:If mounting multiple †SpaceMaker™ appliances and you are installing your
appliance next to the SpaceMaker™ oven (Fig.A.):
• Allow at least 1” between the control panel side of the oven and the appliance.
• Allow at least 4” between the side opposite the control panel of your oven and
adjacent wall or other appliance. You can mount the other appliances flush to
one another.
BC
D
A.
4” 1”
4”
1”

8
9
Note: If you are connecting this appliance to the receptacle of another
†SpaceMaker™ appliance such as the toaster oven or coffeemaker, make sure you
can easily unplug the appliance following use.
13. Your †SpaceMaker™ appliance is now ready for use!
OVERHANGMOLDINGINSTALLATION
Forcabinetswithanoverhangmolding(seeIllustrationC)
Important:Alwayswearprotectiveglassesorgogglestopreventinjurywhen
drilling.
Note:Spacers are provided in case your cabinet has an overhang molding at the
front edge. Only use spacers on the rear screws of the appliance to ensure it is
level with the front.
1. Clear countertop under installation area to avoid getting dust or debris on other
appliances or items. Open cabinets and remove contents to make mounting
easier.
2. Clean both the underside and topside of the bottom panel of the cabinet.
3. Using a ruler, measure the thickness of the overhang molding (G), accurately
noting the number for use in the following step.
Note: If you do not have a ruler, you may cut out the paper ruler provided on the
edge of your mounting template.
4. After measuring the overhang molding thickness as shown in Illustration G, look
at the dashed lines on the mounting template; each line has a measurement
next to it that indicates the thickness of the overhang molding used with that
line. For example, if your cabinet has an overhang molding thickness of ½”,
you will use the ½” dashed line on the template.
5. Fold the template along the dashed line that matches the thickness of your
overhang molding.
6. Place the folded template against the back edge of the overhang molding,
making sure the side with the drill hole marks is facing down (H).
5. Drilling from under the cabinet up, drill holes through the 4 places marked on
the template, using a ¼-inch drill bit (E).
Important:Alwaysensureyouaredrillingstraightupthroughthemarked
mountingholesonthetemplate.Drillingatananglemaypreventproper
installationandmaydamagecabinetsifthedrillbitpiercesthepartition.
6. Once holes are drilled, remove tape and mounting template.
7. Wipe dust and debris off the topside and underside of the cabinet surface.
8. Place a washer inside the cabinet over each of the 4 holes you drilled.
9. Hold appliance in place, aligning front of unit with front edge of cabinet;
drilled holes on cabinet should be aligned with mounting holes on the unit.
10. Drop one of your screws through each of the washers covering the holes in the
cabinet, from inside the cabinet down.
Note: To determine which screws to use, you must have enough of the screw
exposed underneath the cabinet to properly thread the screw into the nut.
11. Screwing from inside the cabinet down into appliance holes, tighten 4 screws
in place to secure appliance to cabinet.
Note: Always tighten screws to ensure the appliance does not move or shake
during operation.
12. Pull out cord from cord storage behind appliance and plug into standard
electrical outlet. Extra cord can be fed back into storage or hung over cord
management hook behind unit (F).
F
G
E
H

0

Note: To determine which screws to use, you must have enough of the screw
exposed underneath the cabinet to properly thread the screw into the nut.
14. Place the appropriate number of spacers determined in step 12 on both of the
rear screws to ensure the appliance will be even (L).
Note:If the height of your overhang molding is too tall to be accommodated by
the number of spacers provided, you may call, toll-free, at 1-800-231-9786 to
order additional spacers at no charge.
Note: For spacer installation, you may require assistance in mounting in order to
hold spacers in place while securing the appliance at the same time. If assistance
is not available, use a small clamp to hold the spacers in place while you position
the appliance.
15. Once spacers are set, hold appliance up and tighten screws to secure. Screw
from inside the cabinet down.
Note: Always tighten screws to ensure the appliance does not move or shake
during operation.
16. Pull out cord from cord storage behind appliance and plug into standard
electrical outlet. Extra cord can be fed back into storage or hung over cord
management hook behind unit (seeillustrationF).
Note: If you are connecting this appliance to the receptacle of another
†SpaceMaker™ appliance such as the toaster oven or coffeemaker, make sure you
can easily unplug the appliance following use.
17. Your †SpaceMaker™ appliance is now ready for use!
Important:Donotalignscrewholesontemplatedirectlyunderthepartition
betweencabinets,asthiswillpreventyoufrominstallingtheapplianceproperly.
Paycloseattentiontowherethedrillholeswillbesetsoasnottodamageyour
cabinetsduringmounting.Drillingthroughyourcabinet’spartitionmaycause
damagetocabinetsandpreventproperinstallation.
7. Making sure to keep the fold line straight against the back edge of the
overhang molding, tape the template securely in place.
8. Drilling from under the cabinet up, drill holes through the 4 places marked on
the template using a ¼-inch drill bit (J).
Important:Alwaysensureyouaredrillingstraightupthroughthemarked
mountingholesonthetemplate.Drillingatananglemaypreventproper
installationandmaydamagecabinetsifthedrillbitpiercesthepartition.
9. Once holes are drilled, remove tape and mounting template.
10. Wipe dust and debris off the underside and topside of the cabinet surface.
11. Place a washer inside the cabinet over each of the 4 holes you drilled.
12. Now, use your ruler or the paper ruler provided to measure the overhang
molding height, placing your ruler vertically against the underside of the
cabinet behind the overhang molding. This number determines the number of
spacers you need, using a number of spacers equal to the overhang molding
height. For example, a 1” overhang molding would use 2, ½” spacers on each
of the rear holes(K).
13. Drop one of your screws through each of the washers covering the holes in the
cabinet, from inside the cabinet down.
J
L
K



HowtoUse
This appliance is for household use only.
OPENINGACAN
1. Lift piercing lever.
2. Tip can so that the rim is under the locating post, then push down on the piercing
lever, making sure the cutter blade is inside the rim of the can (M).
Note:Because of the hands-free feature, it is not necessary to hold the lever down
or hold the can during cutting. However, you may have to support very tall or heavy
cans.
Tip: When the can is opened, the can opener will stop automatically.
3. To remove the can, hold it with one hand and raise the lever with the other.
Caution:Avoidcontactwiththecutedgesofthecanorlids—theyaresharp.During
openingprocess,thedesignofyourcanopenerwillrolltherimofthecantoprevent
sharpedges;however,handlewithcautionandalwayshandlecutlidwithcaution,as
theseedgesarenotrolled.
4. Carefully discard the lid from the magnet.
ImportantTips:
• Do not use this can opener to open cans with a pull tab, peel-off foil seal,
or rolling key or rimless cans.
• Open frozen juices or foods in cardboard cans right from the freezer, while they
are frozen.
• Aluminum lids will not stick to the magnet.
M
USINGTHEKNIFESHARPENER
1. For best results, sharpen the entire blade length in one continuous stroke.
2. Insert blade to be sharpened with the end of the blade closest to the handle on the
knife into the sharpening slot.
3. Carefully press down on the blade and pull it toward you through the slot in one
continuous stroke (N).
Important:Donotsawknifebackandforthtosharpen.Pullthroughthesharpener
inonedirectionwithacontinuous,slow,evenmotion.Failuretodosomaydullor
damageyourblade.
4. Repeat until desired sharpness is achieved.
5. Wash and dry knife before using again.
ImportantTips:
• Use caution when washing and drying knives after sharpening.
• Do not sharpen serrated blades, as this will smooth their edges.
• Do not sharpen scissors.
USINGTHEBOTTLEOPENER
1. Grasp the bottle and position cap above the lip on the back side of the bottle
opener.
2. Tilt bottom of the bottle away from you to catch the cap on the lip and open the
bottle (P).
N
P



USINGTHEBAGCUTTER
1. Grasp the plastic or metal foil bag to be opened by one corner, with one hand
holding the top edge and the other holding the side or bottom, depending on the
size of the bag.
2. Position tightly pulled corner of bag against the cutter and pull firmly to the left to
open the bag (Q).
Note: Pulling a bag straight against the cutter will cut a line along the top of the bag;
pulling at an angle will simply remove the corner.
Q
CareandCleaning
This product contains no user serviceable parts. Refer service to qualified service
personnel.
Important:Unplugthecordbeforecleaningtheunit.
REMOVINGBLADEASSEMBLY
1. Lift the piercing lever up as far as it will go (roughly 90°).
2. Carefully grip the blade assembly and pull it away from the can opener (R).
3. Wash in sudsy water by hand and dry thoroughly. Do not put the blade assembly in
the dishwasher.
4. Before replacing the blade assembly, wipe the can opener body, knife sharpener
and area around the geared wheel with a slightly damp cloth or sponge.
REPLACINGBLADEASSEMBLY
1. Align key post on the blade assembly with key slot on the unit (S).
2. Push in blade assembly and turn clockwise until it locks into position (T).
R
S
T

6
7
INSTRUCCIONESIMPORTANTES
DESEGURIDAD
Cuando se usan aparatos eléctricos, siempre se deben respetar las
siguientes medidas básicas de seguridad:
❑ Por favor lea todas las instrucciones.
❑ A fin de protegerse contra el riesgo de un choque eléctrico, no sumerja
el cable, los enchufes ni el aparato en agua ni en ningún otro líquido.
❑ Todo aparato eléctrico usado en la presencia de los niños o por ellos
mismos requiere la supervisión de un adulto.
❑ Desconecte el aparato del tomacorriente cuando no esté en uso, antes
de instalarle o retirarle piezas y antes de limpiarlo.
❑ Evite el contacto con las piezas móviles.
❑ No use ningún aparato eléctrico que tenga el cable o el enchufe
averiado, que presente un problema de funcionamiento o que esté
dañado. Acuda a un centro de servicio autorizado para que lo
examinen, reparen o ajusten o llame gratis al número correspondiente
en la cubierta de este manual.
❑ El uso de accesorios no recomendados por el fabricante del aparato
puede ocasionar incendio, choque eléctrico o lesiones.
❑ No use este aparato a la intemperie.
❑ No abra latas (tipo aerosol) presurizadas.
❑ No abra latas de líquidos inflamables tales como las de los líquidos
encendedores.
❑ Para evitar el riesgo de incendio o choque eléctrico, no opere ningún
artefacto de calefacción debajo del montaje de este aparato.
❑ No instale el soporte de almacenaje / aparato sobre ni cerca de ninguna
superficie de un aparato de calentar o de cocina ni sobre una pila o
fregadero.
CONSERVEESTAS
INSTRUCCIONES.
Esteaparatoeléctricoesparausodomésticoúnicamente.
ENCHUFEPOLARIZADO(Solamenteparalosmodelosde0V)
Este aparato cuenta con un enchufe polarizado (un contacto es más ancho que el
otro). A fin de reducir el riesgo de un choque eléctrico, este enchufe encaja en un
tomacorriente polarizada en un solo sentido. Si el enchufe no entra en el tomacorriente,
inviértalo y si aun así no encaja, consulte con un electricista. Por favor no trate de
alterar esta medida de seguridad.
TORNILLODESEGURIDAD
Advertencia:Esteaparatocuentaconuntornillodeseguridadparaevitar
laremocióndelacubiertaexteriordelmismo.Afindereducirelriesgode
incendioodechoqueeléctrico,porfavornotratederemoverlacubierta
exterior.Esteproductonocontienepiezasreparablesporelconsumidor.
Todareparaciónsedebellevaracaboúnicamenteporpersonaldeservicio
autorizado.
CABLEÉLECTRICO
a) El producto se debe de proporcionar con un cable eléctrico corto (o uno
separable), a fin de reducir el riesgo de tropezar o de enredarse en un cable
más largo.
b) Existen cables eléctricos más largos y separables o cables de extensión que uno
puede utilizar si toma el cuidado debido.
c) Si se utiliza un cable separable o de extensión,
1) El régimen nominal del cable separable o del cable de extensión debe ser,
como mínimo, igual al del régimen nominal del aparato.
2) Si el aparato es de conexión a tierra, el cable de extensión debe ser un
cable de tres alambres de conexión a tierra.
3) Uno debe de acomodar el cable más largo de manera que no cuelgue del
mostrador o de la mesa, para evitar que un niño tire del mismo o que
alguien se tropiece.
Nota:Si el cordón de alimentación es dañado, en América Latina debe sustituirse
por personal calificado o por el centro de servicio autorizado.

8
9
Elproductopuedevariarligeramentedelqueapareceilustradoaquí.
 . Cortabolsas
 . Afiladordecuchillos
 . Compartimientoparaelcable
 . Tapa
† . Montajedelacuchilla,conmagneto(PiezaNºC00)blanco,(PiezaNºC00)negro
 6. Guíadecolocación
 7. Palancadeperforación
 8. Compartimientoparaelcable(nomostrado)
 9. Ganchoparaafianzarelcable(nomostrado)
†0. Juegodepiezasdemontaje(PiezaNºC00-0)blanco,(PiezaNºC00-0)negro
  (nomostrado)
Nota:†indica piezas desmontables/reemplazables por el consumidor







A †. Piezasparaelensamblaje
  (PiezaNºSDC-MOUNTINGKIT)
  A. 6Separadores
  ½"
  ¼"
  /6"
  /6"
  B. Tornillos
  "
  ½"
  ¼"
  C. Arandela
 . Plantillaparaelensamblaje(encaja)
Tambiénnecesitará:
• Cintaadhesiva
• Regla(opuedetambiéncortarlareglaqueseproporcionaconlaplantilla)
• Taladroeléctricoconbrocade¼”
A
C
B
A