Black & Decker BXCM0401IN User manual

BXCM0401IN
WARRANTY TERMS AND CONDITIONS
Stove Kraft Limited warrants to the purchaser of products for a period of 2 Years
commencing from the date of invoice, the company will repair or replace free of
charge any part or parts of the product, should the company be fully satisfied in
its sole discretion, that the defect/s is/are due to faulty material or workmanship
only. The warranty will be governed by the following clauses.
1) The company or their Authorised Service Agent will repair / replace all parts
that are failing due to faulty material or defective workmanship pertaining to
the aboveproduct.
2) Only the Company or its Authorised Service Agent can service / repair or
attend to install/reinstall the above product.
3) On-site warranty will be executed. The warranty will be executed at
customer place / authorized dealer / service centers and in which the
authorized representative is situated including outstation locations.
4) The warranty extended herein is in lieu of all implied conditions & warranties
under the law and is confined to the repair or replacement of defective parts
and does not cover any consequential or resulting liability, damage or loss
arising from such defects. Further more, the warranty in no case shall extend
to the payment or any monetary consideration whatsoever, of the replace
ment or return of the product as a whole.
5) This warranty excludes consumables, corrosive, plastic, rubber and glass
components adding decorative value to the product.
6) The company is not liable to carry out any servicing work under the warranty.
7) The courts of competent Jurisdiction at Bangalore, Karnataka shall have
exclusive Jurisdiction over all matters arising out of any disputes in relation
to product.
8) Stove Kraft shall not be liable to replace or repair the good under the terms
of warranty
where:
a) The fault has been caused or is attributable to accidental use, misuse,
negli gent use or used contrary to the manufacturer recommendation
b) The appliance has been used on a voltage supply other than that
stamped on the product.
c) Repairs have been attempted by persons other than the company or
their authorized service agent.
Imported & Marketed by
Stove Kraft Limited
An Iso 9001 : 2015 Certified Company
#81, Harohalli Industrial Area, Kanakapura Taluk, Ramanagara District - 562 112, Karnataka, India
for Customer Complaints, Contact:
Customer Care Address: Same as Above, Manager, Consumer Care Cell | Toll Free No.: 1800-425-66666
Email: [e-mail] | Website: Www.stovekraft.com
Country of Origin: People's Republic Of China

CONTENTS
Know Your Coffee Maker 1
Intended Use 2
Safety Instructions 2
Using Your Appliance 2
Safety Of Others 3
After Use 3
Inspection And Repairs 3
Electrical Safety 4
Extension Cables & Class 1 Product 4
Mains Plug Replacement 4
Additional Safety Instructions For Coffee Makers 5
Use 5
A．Make Espresso Coffee 6
B. Frothing Milk/ Make Cappuccino 7
Cleaning And Maintenance 8
Protecting The Environment 9
Trouble Shooting 10

1 2
KNOW YOUR COFFEE MAKER INTENDED USE
SAFETY INSTRUCTIONS
USING YOUR APPLIANCE
Your Black+Decker coffee maker has been designed for making coffee.
This product is intended for household use only. Thank you for choosing Black &
Decker. We hope that you will enjoy using this product for many years.
Read this entire manual carefully before using the appliance.
Warning! When using mains-powered appliances, basic safety precautions,
including the following, should always be followed to reduce the risk of fire,
electric shock and personal injury.
• The intended use is described in this manual. The use of any accessory or
attachment or the performance of any operation with this appliance other
than those recommended in this instruction manual may present a risk of
personal injury.
• Retain this manual for future reference.
• Always take care when using the appliance.
• Do not use the appliance outdoors.
• Do not operate the appliance if your hands are wet. Do not operate the
appliance if you are barefoot.
• Guide the power supply cord neatly so it does not hang over the edge of a
worktop and cannot be caught accidentally or tripped over.
• Never pull the power supply cord to disconnect the plug from the socket.
Keep the power supply cord away from heat, oil and sharp edges.
• If the power supply cord is damaged during use, disconnect the appliance
from the power supply immediately. Do not touch the power supply
immediately. Do not touch the power supply cord before disconnecting from
the power supply.
• Disconnect the appliance from the power supply when not in use and before
cleaning.
Steel Mesh
Metal Funnel
Press Bar
Carafe Cover
Tank Cover
Knob
Indicator
Frothing Device
Drip Tray
Handle
Carafe

3 4
INSPECTION AND REPAIRS
MAINS PLUG REPLACEMENT
SAFETY OF OTHERS ELECTRICAL SAFETY
AFTER USE
EXTENSION CABLES & CLASS 1 PRODUCT
• The appliance is not intended for use by persons (including children) with
reduced physical sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the
appliance.
• Switch off, remove the plug from the socket and let the appliance cool down
before leaving it unattended and before changing, cleaning or inspecting any
parts of the appliance.
• When not in use, the appliance should be stored in a dry place. Children should
not have access to stored appliances.
• Switch off the appliance before cleaning, changing accessories or approaching
parts which move in use.
• Before use, check the appliance for damaged or defective parts. Check for
breakage of parts, damage to switches and any other conditions that may
affect its operation.
• Do not use the appliance if any part is damaged or defective.
• Have any damaged or defective parts repaired or replaced by an authorized
repair agent.
• Before use, check the power supply cord for signs of damage, ageing & wear.
• Do not use the appliance if the power supply cord or mains plug is damaged
or defective.
• If the power supply cord or mains plug is damaged or defective it must be
repaired by an authorized agent in order to avoid a hazard. Do not cut the
power supply cord and do not attempt to repair it yourself.
• Never attempt to remove or replace any parts other than those specified in
this manual.
Before use, check that the mains voltage corresponds to the voltage on the
rating plate.
This product must be earthed. Always check that the mains voltage corresponds
to the voltage on the rating plate.
Appliance plugs must match the outlet. Never modify the plug in any way.
Do not use any adaptor plug in any way. Do not use any adaptor plugs with
earthed (Class 1) appliances.
Unmodified plugs and matching outlets will reduce the risk of electric shock.
• A 3 core cable must be used as your tool is earthed and of class 1 construction.
• Up to 30m (100 ft) can be used without loss of power. If supply cord is
damaged, it must be replaced by the manufacturer or an authorized
Black & Decker Service Centre in order to avoid a hazard.
If a new mains plug needs to be fitted:
• Safely dispose of the old plug
• Connect the brown lead to the live terminal of the new plug
• Connect the blue lead to the neutral terminal
• If the product is class I (earthed), connect the green/yellow lead to the earth
terminal.
Note: If your product is class II double insulated (only 2 wires in the cord set), no
connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Any replacement fuse must be of the same rating as the original fuse supplied
with the product.
Warning! The above section on mains plug replacement is for authorized service
centre personals

1. Remove the tank cover by turning it anti-clockwise and pour appropriate
water in the tank. Do not exceed the maximum capacity of the carafe.
Note: 1. The carafe has marks with a maximum tank capacity of 4 cups and
the minium capacity of 2 cups.
2. Before pouring the water into the water tank, be sure the power
cord is unplugged from the power outlet and the steam knob is in
the position.
2. Put the tank cover in place by turning clockwise until it locks in position.
3. Put the steel mesh into the metal funnel. Add coffee powder in the steel
mesh with a measuring spoon. One spoon coffee powder can make about
one cup of top-grade coffee.
Note: ①Select the quantity of coffee powder to make 2 or 4 cups of coffee.
②Please use coarse coffee powder for smooth operation.
4. Make sure the tubers on the funnel align with the grooves in the appliance
and then insert the funnel and place it rightly in the “INSERT” position.
You can fix the funnel into the coffee maker firmly by turning it
anti-clockwise until it is locked in the “LOCK” position (see Fig. 1).
5. Place the carafe on the removable tray.
6. Plug the power cord into the socket.
7. Turn the steam knob to position, and
the indicator is illuminated. Wait for about
2 minutes, till the coffee starts flowing out.
8. After the desired coffee is ready,
I. Turn steam knob to position.
II. The indicator goes off and the coffee maker stops working.
III. Your coffee is ready now.
IV. Remove the carafe and turn the steam control knob to position and
release the residual steam in the tank.
WARNING: Do not leave the coffee maker unattended while making your coffee.
9. Before removing the steel mesh or opening the tank cover, make sure the
pressure in the tank is released. The method is to turn the steam knob to
the position first. The steam in the tank will eject from the frothing
device. After the pressure is released, wait for the steel mesh to cool down
before removing it or opening the tank cover.
10. After the coffee is made, take out the funnel by turning clockwise and
remove the residual coffee from the steel mesh. Once cool, rinse it with
running water and assemble it back.
5 6
ADDITIONAL SAFETY INSTRUCTIONS FOR COFFEE MAKERS A．MAKE ESPRESSO COFFEE
USE
Warning! The lid may become hot during use.
Warning! Steam may escape from the unit.
• Allow the appliance to cool before fitting or removing any parts and before
cleaning.
• During use, the carafe and the hotplate can get very hot.
• Do not use the appliance if the carafe shows any signs of cracks.
• Do not immerse the appliance in liquid.
Warning! Never use the appliance without water in the reservoir.
Before first use
• Unpack the coffee maker and remove all packaging, promotional materials
and stickers. Remove all printed documents.
• Check that your mains supply is the same as the one indicated on the
appliance.
• Position the appliance on a flat, stable work surface, away from the edge and
other electrical appliances. Ensure that the coffee maker is not positioned
under any cupboards or near furnishings, wallpaper or similar that could be
damaged by hot steam.
• Wash all removable parts of the appliance in warm, soapy water. Rinse and
dry thoroughly with a soft water. Rinse and dry thoroughly with a soft cloth.
Do not use harsh/abrasive cleaners or place any part of the appliance in the
dishwasher.
Warning! Never immerse the main body of the appliance, cord set or plug in
water or any other liquid.
• We recommend that you first familiarize yourself with all parts of the
appliance before using it for the first time. Do not fill the water or connect to
the mains supply when doing this.
• To remove any remaining residue from the manufacturing process, we recom
mend operating the coffee maker as described in the ‘Use’ section. This will
flush the appliance out. Use water only, do not add coffee.
Note! Ensure that the coffee maker mains cord does not overhang the edge of
the worktop.
Note! When the coffee maker is plugged in and operated for the first time, there
may be a small amount of smoke and/or odour as the heating elements warm up.
This represents no danger or malfunction with the product and should be clear
after a couple of uses.
LOCK
Fig. 1
INSERT

7 8
B. FROTHING MILK/ MAKE CAPPUCCINO CLEANING AND MAINTENANCE
You get a cup of cappuccino when you top up a cup of espresso with frothing
milk.
Method:
1. Prepare espresso in a cup big enough as mentioned above.
2. Fill a jug with desired amount of milk for each cup of cappuccino to be
prepared. You are recommended to use whole milk at a normal / cold
temperature.
Note: In choosing the size of jug, it is recommended that the diameter is not
less than 70±5mm, as volume of milk is likely to increase.
3. Turn the steam knob to the position, the indicator will light up.
4. Insert the frothing device into the milk about two centimeters for 2 minutes
and the steam will come out from the frothing device.
Note: Please do not fill too much water (should be≤150ml), or else steam
output will be little and the water content in frothing milk will be
too much.
5. When the required purpose is served, you can turn the steam control knob
to position and stop frothing. Remove the jug and turn the steam
control knob to position and release the residual steam in the tank.
Note: ①Clean steam outlet with wet sponge immediately after the steam
stops generating.
②You can only open the tank cover after you drain the water and
release the pressure.
6. Pour the frothed milk into the espresso prepared and your cappuccino is
ready. To sweeten the taste, sprinkle the froth with a little cocoa powder.
Note: We recommend you allow the appliance to cool down before making
coffee again.
1. Cut off power source and let the coffee maker cool down completely before
cleaning.
2. Clean the housing of coffee maker with moisture-proof sponge often.
Note: Do not clean with alcohol or solvent cleanser. Never immerse the
housing in water for cleaning.
3. Detach the metal funnel after turning it clockwise, get rid of residual coffee
inside and rinse with clean water.
4. Clean all the detachable attachments in the water and dry thoroughly.

9 10
TROUBLE SHOOTING
The coffee maker
is not getting
switched on
The power is cut off
Plug the power cord into the
power point. If the appliance
still does not work, please
contact the authorized
service centre
Carafe leakage
The carafe is not placed
properly
Let the centreline of the
carafe align the postion as
recomended
The level of water in the
tank exceeds the Max level
The water level in the tank
should be within Min and Max
The metal parts
in the tank have
rusted
Due to the quality of water
Use the descaler
recommended by
manufacturer
Water leaks from
the bottom of the
coffee maker
There is more water in the
drip tray Please clean the drip tray
The coffee maker is not
working properly
Please contact authorized
service centre for support
Water leaks
from filter.
Coffee powder on
filter edge Please clean the powder
Bad taste in
your coffee.
Product is not cleaned
properly
Clean coffee maker as
recommended
The coffee powder is
stored in a hot, wet place
for a long time. The coffee
powder has turned bad
Please use fresh coffee
powder, or store unused
coffee powder in a cool, dry
place. After opening a
pack of coffee powder, reseal
it tightly and store it in a
refrigerator to maintain its
freshness
The steam is not
getting frothed
The steam ready indicator
(green indicator) is not
illuminated
Only after the steam ready
indicator (green indicator) is
illuminated, the steam can
be used to froth
The container is too big Use high and narrow cup
You have used skimmed
milk
Use whole milk or half-
skimmed milk
Symptom Cause Corrections
TECHNICAL DATA
PROTECTING THE ENVIRONMENT
Model : BXCM0401IN
Voltage : 220-240V AC, 50 Hz / 60 Hz
Power : 800 W
Weight : 1.83 Kg
You can help protect the environment!
Please remember to respect the local regulations:
hand in the non-working electrical equipments to an
appropriate waste disposal center.

YOUR NAME _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
YOUR ADDRESS _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
POSTCODE _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
DATE OF PURCHASE _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
DEALERS NAME & ADDRESS _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
PRODUCT MODEL NO.
BXCM0401IN
WARRANTY REGISTRATION FORM