Black & Decker Press&Steam HGS500 User manual

PB
1
blackanddeckerappliances
2-in-1 Iron & Steamer
Plancha y Vaporizador 2 en 1
use and care manual
manual de uso y cuidado
HGS500

2
3

2
3
IMPORTANT SAFETY INSTRUCTIONS
When using your iron/steamer, basic safety precautions should
always be followed, including the following:
• READ ALL INSTRUCTIONS BEFORE USING.
• Use iron/steamer only for intended use.
• To protect against risk of electric shock, do not immerse the iron/
steamer in water or other liquids.
• Always turn the iron/steamer OFF before plugging or unplugging the
iron from the electrical outlet.
• Never yank cord to disconnect from the outlet; instead grasp plug and
pull to disconnect.
• Keep the cord away from the heated surfaces. Do not wrap the cord
around the appliance. Let the iron/steamer cool completely before
putting the iron/steamer away.
• Always disconnect iron/steamer from electric outlet before filling with
water, cleaning, or emptying and when not in use.
• Do not operate the iron/steamer if it has been dropped, if there
are visible signs of damage to the iron/steamer or its cord, or if it’s
leaking. To avoid the risk of electric shock, do not dissemble the iron/
steamer; take it to a qualified service person for examination and
repair, or call the appropriate toll-free number on the cover of this
manual. Incorrect reassembly can cause risk of electric shock when
the iron/steamer is used.
• Close supervision is necessary for any appliance being used by or near
children. Do not leave iron/steamer unattended when plugged in or on
an ironing board.
• Burns can occur from touching hot metal parts, hot water, or steam.
Use caution when you turn a steam iron/steamer upside down—there
might be hot water in the reservoir. Avoid rapid movement of iron/
steamer to minimize hot water spillage.
• This appliance is not intended for use by persons (including children)
with reduced physical, sensory, or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliances by a person
responsible for their safety.
• Children should be supervised to ensure that they do not play with the
appliance.
• The iron/steamer must be used and rested on a stable surface.
• When standing the iron/steamer on its heel, ensure that the surface on
which the iron/steamer is placed is stable.
SPECIAL INSTRUCTIONS
• To avoid circuit overload, do not operate another high wattage
appliance on the same circuit.
• If an extension cord is absolutely necessary, a 15-ampere cord should
be used. Cords rated for less amperage can result in a risk of fire or
electrical shock due to overheating. Care should be taken to arrange
the cord so that it cannot be pulled or tripped over.
SAVE THESE INSTRUCTIONS.
This product is for household use only.

4
5
POLARIZED PLUG
This appliance has a polarized plug (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit
into a polarized outlet only one way. If the plug does not fit fully into
the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to modify the plug in any way.
TAMPER-RESISTANT SCREW
Warning: This appliance is equipped with a tamper-resistant screw
to prevent removal of the outer cover. To reduce the risk of fire or
electrical shock, do not attempt to remove the outer cover. There are no
user-serviceable parts inside. Repair should be done only by authorized
service personnel.
Note: If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in order to
avoid a hazard. Please contact the Customer Care line listed below.
Customer Care Line: 1-800-465-6070
For online customer service:
www.prodprotect.com/blackanddecker

4
5
Product may vary slightly from what is illustrated.
1. Ceramic soleplate
2. Steam trigger lock
3. Steam trigger
4. Water inlet
5. Water tank
6. Power light
7. Power button
8. Heel rest
† 9. Delicate fabric attachment
† 10. Upholstery attachment
† 11. Heat resistant bag
Note: † indicates consumer
replaceable/removable parts.
11
910
GETTING TO KNOW YOUR
2-IN-1 IRON & STEAMER
14
5
6
3
2
7
8

6
7
HOW TO USE
This product is for household use only.
GETTING STARTED
• Remove all labels, tags and stickers attached to the
body, cord, or soleplate of the iron/steamer and the
plastic band around the power plug.
• Remove and save literature.
• Please note that water droplets may still be visible
in the tank at the time of purchase. This is from the
individual quality tests done to ensure that every
iron/steamer meets our high standards for product
performance.
IMPORTANT INFORMATION
• For best performance, we recommend using distilled,
purified or filtered water in your steamer. Tap water
contains minerals that can build up inside your iron/
steamer over time and reduce its efficiency or even
cause damage.
• Never use perfumes, oils or other additives.
• Always check the garment’s care label before
steaming, and always test fabrics for colorfastness
in an inconspicuous area. Steamers are not
recommended for use on leather, suede, vinyl, plastic,
or other materials that are sensitive to steam.
• During use the iron/steamer and accessories will
become HOT. Never try to fit or remove attachments
while still hot.
• After preheating, prime the water pump by holding
the steam trigger until steam forms.
• It is normal to feel or hear the water pump inside the
device. It may become louder when the water level
in the tank is low. Check and refill the tank when
required.
• Small amounts of dripping might occur during use. If
excessive, your iron/steamer needs time to get back
up to full temperature. Just allow the iron/steamer a
minute to reheat.
• Wearing clothes immediately after ironing or steaming
can actually create wrinkles. Always allow the clothing
to cool for about 5 minutes before wearing.
ATTACHMENTS
Your iron/steamer has two attachments. Each attachment
is marked with an icon.
Delicate fabric
attachment
Reduces the possibility of damage to
fabrics such as silk and lace.
Tip: For items with printing/
embellishment, turn the garment
inside out to avoid damage to
sensitive areas.

6
7
Upholstery
attachment
Refresh and clean larger materials
such as bedding, mattresses,
curtains, soft toys, sofas and much
more.
Always test for colorfastness and heat
sensitivity on an inconspicuous area.
ATTACHING/REMOVING (FIG. A)
1. Make sure that the iron/
steamer and attachment
are cool.
2. Hook the top of the
attachment over the top
edge of the steamer.
3. Click the bottom edge into
place.
4. Remove attachments by lifting them away from your
iron/steamer starting at the heel. When removing the
attachment, watch out for condensation that may
have built up during use.
FILLING
1. Place the
iron/steamer
as shown
(Fig. B). You
can also
place your
iron/steamer on the heat resistant storage bag.
2. Open the water inlet cover (Fig. C).
3. Pour slowly, to let the air in the
reservoir escape, otherwise you’ll
cause an air lock and the water will
overflow.
4. Don’t fill past the max marking or
water will escape in use.
5. To refill at any time during use, turn the iron/steamer
off by pressing the power button until the blue
indicator light goes out, unplug from outlet, and
follow the above procedure.
6. After refilling, allow to reheat for 45 seconds and then
prime the pump by holding the steam trigger until
steam forms.
USING
1. If the label says “do not iron” or shows this icon ,
install the delicate attachment and make sure to test
on an inconspicuous area prior to steaming the entire
garment.
2. If the label says “do not steam” or shows this icon ,
do not steam the garment.
3. Hang the garment in an area that will not be
affected or damaged by the heat and steam, such
as on a shower curtain rail, or in an open doorway.
Alternatively, place the garment on a bed or towel.
A
C
B

8
9
You can use the heat resistant bag between the
towel/bed and garment if required.
4. Install any attachment you wish to use. (optional)
5. Plug the iron/steamer in then press the power
button. The blue power button light will slowly flash,
indicating that the iron/steamer is heating.
6. After about 45 seconds the power light will stay on,
indicating your iron/steamer is ready to use.
7. Prime the water pump by holding steam trigger until
steam forms.
8. To generate steam, press the steam trigger. As long as
the trigger is held, steam will emit from the steamer.
When the trigger is released, the steam will stop.
9. To generate a constant flow of steam without holding
the trigger, press the steam trigger and then slide the
steam trigger lock downwards. You can then release
pressure on the steam trigger.
To turn the steam off, press
the trigger, slide the steam
trigger lock upwards, then
release the trigger.
10. With your free hand keep
the fabric taut. Steam the
garment with slow, downward
strokes, keeping the head of
the iron/steamer in contact
with the fabric (Fig. D).
11. When you have finished, press and hold the power
button until the blue light goes out (about 3 seconds)
and unplug.
12. After ironing or between garments, set your iron/
steamer down with the handle resting on a flat, stable
surface. You can use the heat resistant bag to rest
your iron/steamer on (Fig. B).
FABRIC SOFTENING INFUSED SOLEPLATE
Your iron/steamer features a ceramic heated plate that
helps smooth out wrinkles and creases on the areas of
garments that are more difficult to reach with steam
alone. The fabric softening infused ceramic sole plate
helps condition fabrics to defend against wrinkles and
reduce static. The temperature of the plate is safe for all
ironable fabrics.
To press garments (collars, cuffs, etc.) place it on a flat,
heat resistant surface. Keep the plate in contact with the
garment. Use steam as required. You can use the heat-
resistant bag to iron on (Fig E).
Important: Always make sure that the surface you use to
iron on will not be affected or damaged by heat or steam!
D

8
9
CARE AND MAINTENANCE
This product contains no user serviceable parts. Refer to
service qualified service personnel.
1. Make sure iron/steamer is off, unplugged and
completely cool.
2. Wipe all surfaces with a clean damp cloth.
3. After the iron/steamer has been thoroughly dried,
turn it back on and lightly steam over an old cloth.
This will help remove any residue left in the steam
holes.
4. To avoid mineral buildup, empty the tank after each
use.
CLEANING ATTACHMENTS
• Delicate fabric attachment: Wash with cold water and
small amounts of a gentle cleanser if needed. The
fabric cannot be removed.
• Upholstery attachment: The fabric can be removed
and hand washed with cold water and a gentle
cleanser.
STORAGE
Unplug the iron/steamer whenever it is not in use. Allow
it to cool, then store it out of reach of children in a safe,
dry location. Never wrap the cord around the appliance.
This will cause the cord to wear prematurely and break,
thus voiding the warranty. Handle the cord carefully and
avoid jerking, twisting, or straining it, especially at plug
connections.

10
11
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
Not enough steam or no
steam is coming out of the
steamer.
The iron/steamer is not heated to full
temperature.
Always allow iron/steamer to preheat at
least 45 seconds, or until the power button
light stops flashing.
There is not enough water in the water tank. Fill the water tank.
The water pump hasn’t been primed. If unit
still will not steam, move the unit around or
shake to assist with priming.
After preheating, always prime the water
pump by holding the steam trigger until
steam forms.
Discolored water is
coming through the holes
and staining the fabric.
Residue has built up in the water tank. Empty the water tank after each use. Only
use distilled, filtered, or purified water.
Perfumed or scented additives were used. Never use perfumed or scented additives.
Iron/steamer is leaking or
spitting.
Iron/steamer is not hot enough. Allow the iron/steamer to heat for about 45
seconds.
Water tank is running low. Fill the water tank.