Black & Decker BESTE625 User manual

www.blackanddecker.eu
BESTE625
BESTE628
BESTE630
15 2
4
3
6
9
7
810
Переклад оригінальних інструкцій
Інструмен т не
призначений для
професійного
використання.

2
English (Original instructions) 7
Українська (переклад оригінальних інструкцій) 17

3
6
C
E
B
A
D
F
25
11
7
9a
10
8
26
12
13
5

4
2
3
14
4
GH
60cm
I
6
L
5º - 10º
J
K

5
10a
16
15
N
18
19
17
O
19
P
20
Q
26
27
R
M

6
21
22
ST

ENGLISH
7
Intended use
Your BLACK+DECKER BESTE625, BESTE628, BESTE630
EASYFEED trimmers have been designed for trimming and
finishing lawn edges and cutting grass in confined spaces.
These machines are intended for consumer use only.
Safety instructions
Warning! When using mains-
powered machines, basic safety
precautions, including the following,
should always be followed to
reduce the risk of fire, electric
shock, personal injury and material
damage.
Warning! When using the machine
the safety rules must be followed.
For your own safety and bystanders
please read these instructions
before operating the machine.
Please keep the instructions safe
for later use.
♦Read all of this manual carefully
before operating the machine.
♦The intended use is described in
this manual.
♦The use of any accessory or
attachment or the performance of
any operation with this machine
other than those recommended
in this instruction manual may
present a risk of personal injury.
♦Retain this manual for future
reference.
Using your machine
Always take care when using the
machine.
♦Always use safety glasses or
goggles.
♦Never allow children or people
unfamiliar with the instructions to
use the machine.
♦Never operate the machine while
people, especially children, or
pets are nearby.
♦Close supervision is necessary
when the machine is used near
children.
♦This machine is not intended for
use by young or infirm persons
without supervision.
♦This machine is not to be used
as a toy.
♦Only use the machine in daylight
or good artificial light.
♦If the machine starts to vibrate
abnormally or if you hit a foreign
object, switch the appliance off
and remove the plug from the
socket. Check for any damage to
the appliance, replace or repair
any damaged parts, check for
and tighten any loose parts.

ENGLISH
8
♦Cleaning and user maintenance
shall not be made by children
without supervision.
Residual risks
Additional residual risks may arise
when using the tool which may not
be included in the enclosed safety
warnings. These risks can arise
from misuse, prolonged use etc.
Even with the application of the
relevant safety regulations and the
implementation of safety devices,
certain residual risks can not be
avoided. These include:
♦Injuries caused by touching any
rotating/moving parts.
♦Injuries caused when changing
any parts, blades or accessories.
♦Injuries caused by prolonged use
of a tool.
♦When using any tool for
prolonged periods ensure you
take regular breaks.
♦Impairment of hearing.
♦Health hazards caused by
breathing dust developed when
using your tool (example:-
working with wood, especially
oak, beech and MDF).
♦Avoid using the machine in bad
weather conditions especially
when there is a risk of lightning.
♦Use in a dry location only. Do
not allow the machine to become
wet.
♦Do not immerse the machine in
water.
♦Do not open the body casing.
There are not user-serviceable
parts inside.
♦Do not operate the machine in
explosive atmospheres, such as
in the presence of flammable
liquids, gases or dust.
♦To reduce the risk of damage
to plugs or cords, never pull the
cable to remove the plug from
a socket.
Safety of others
♦Never allow children, persons
with reduced physical, sensory
or mental capabilities or lack
of experience and knowledge
or people unfamiliar with these
instructions to use the machine,
local regulations may restrict the
age of the operator.
♦Children shall not play with the
machine.

ENGLISH
9
when it is running idle in addition to
the trigger time.
After use
♦When not in use, the machine
should be stored in a dry, well
ventilated place out of reach of
children.
♦Children should not have access
to stored machines.
♦When the machine is stored
or transported in a vehicle it
should be placed in the boot or
restrained to prevent movement
following sudden changes in
speed or direction.
Inspection and repairs
♦Before use, check the machine
for damaged or defective parts.
♦Check for breakage of parts and
any other conditions that may
affect its operation.
♦Do not use the machine if any
part is damaged or defective.
♦Have any damaged or defective
parts repaired or replaced by an
authorised repair agent.
♦Never attempt to remove or
replace any parts other than
those specified in this manual.
Vibration
The declared vibration emission
values stated in the technical data
and the declaration of conformity
have been measured in accordance
with a standard test method
provided by EN50636 and may be
used for comparing one tool with
another.
The declared vibration emission
value may also be used in
a preliminary assessment of
exposure.
Warning! The vibration emission
value during actual use of the
power tool can differ from the
declared value depending on the
ways in which the tool is used. The
vibration level may increase above
the level stated.
When assessing vibration exposure
to determine safety measures
required by 2002/44/EC to protect
persons regularly using power tools
in employment, an estimation of
vibration exposure should consider,
the actual conditions of use and
the way the tool is used, including
taking account of all parts of the
operating cycle such as the times
when the tool is switched off and

ENGLISH
10
♦Wear long trousers to protect
your legs.
♦Before using the machine, check
that your cutting path is free from
sticks, stones, wire and any other
obstacles.
♦Only use the machine in the
upright position, with the cutting
line near the ground. Never
switch the machine on in any
other position.
♦Do not overreach and to keep
your balance at all times. Always
be sure of your footing on slopes
and walk, never run.
♦Do not work on steep slopes.
Work across the face of slopes,
not up and down.
♦Move slowly when using the
machine. Be aware that freshly
cut grass is damp and slippery.
♦Never cross gravel paths or
roads while the machine is
running.
♦Do not to touch moving
hazardous parts before the
machine is disconnected from
the mains and the moving
hazardous parts have come to
a complete stop.
Additional safety
instructions for grass
trimmers
Warning! Cutting elements
continue to rotate after the motor is
switched off.
♦Be familiar with the controls and
the proper use of the machine.
♦Before use, check the power
supply cord and extension cord
for signs of damage, ageing and
wear.
♦If a cord becomes damaged
during use, disconnect the
cord from the mains supply
immediately. DO NOT
TOUCH THE CORD BEFORE
DISCONNECTING THE
SUPPLY.
♦Do not use the machine if the
cords are damaged or worn.
♦Before using the machine and
after any impact, check for signs
of wear or damage and repair as
necessary.
♦Always ensure that the ventilation
slots are kept clear of debris.
♦Wear stout shoes or boots to
protect your feet.