Black & Decker Powerful Solutions NW36XXY User manual

1
NW36XXY
NW48XXY
Powerful Solutions TM
www.blackanddecker.co.uk
2 1
2
1

2
English (Original instructions) 5

3
3
4
4
3
1
A B
C1 C2
D E

4
2
2
5 6
7
78
F G
H

5
Intended use
Your Black & Decker Dustbuster® hand
held vacuum cleaner has been designed
for light wet and dry vacuum cleaning
purposes. This product is intended for
household use only.
Safety instructions
uWarning! When using battery-
powered appliances, basic safety
precautions, including the following,
should always be followed to reduce
the risk of re, leaking batteries,
personal injury and material
damage.
uRead this manual carefully before
using the appliance.
uThe intended use is described in this
manual. The use of any accessory
or attachment or the performance of
any operation with this appliance
other than those recommended in
this instruction manual may present
a risk of personal injury.
uRetain this manual for future
reference.
Using your appliance
uDo not use the appliance to pick up
liquids or any materials that could
catch re.
uDo not use the appliance near water.
Do not immerse the appliance in
water.
uNever pull the charger lead to
disconnect the charger from the
socket. Keep the charger lead away
from heat, oil and sharp edges.
After use
uUnplug the charger before cleaning it.
uWhen not in use, the appliance
should be stored in a dry place.
Children should not have access to
stored appliances.
Inspection and repairs
uBefore use, check the appliance for
damaged or defective parts. Check
for breakage of parts, damage to
switches and any other conditions
that may affect its operation.
uDo not use the appliance if any part
is damaged or defective.
uHave any damaged or defective parts
repaired or replaced by an authorised
repair agent.
uRegularly check the charger lead for
damage. Replace the charger if the
lead is damaged or defective.
uNever attempt to remove or replace
any parts other than those specied
in this manual.
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings.
These risks can arise from misuse,
prolonged use, etc.
Even with the application of the relevant
safety regulations and the implementation
of safety devices, certain residual risks
can not be avoided. These include:
uInjuries caused by touching any
rotating/moving parts.
uInjuries caused when changing any
parts, blades or accessories.
uInjuries caused by prolonged use of a
tool. When using any tool for
prolonged periods ensure you take
regular breaks.
uImpairment of hearing.
uHealth hazards caused by breathing
dust developed when using your tool
(example: working with wood,
especially oak, beech and MDF).
Safety of others
uThis appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
uChildren should be supervised to
ensure that they do not play with the
appliance.

6
Additional safety instructions for
batteries and chargers
Batteries
uNever attempt to open for any reason.
uDo not expose the battery to water.
uDo not expose the battery to heat.
uDo not store in locations where the
temperature may exceed 40 °C.
uCharge only at ambient temperatures
between 10 °C and 40 °C.
uCharge only using the charger
provided with the appliance/tool.
uWhen disposing of batteries, follow
the instructions given in the section
"Protecting the environment".
uDo not damage/deform the battery
pack either by puncture or impact, as
this may create a risk of injury and re.
uDo not charge damaged batteries.
uUnder extreme conditions, battery
leakage may occur. When you notice
liquid on the batteries, proceed as
follows:
uCarefully wipe the liquid off using a
cloth. Avoid skin contact.
uIn case of skin or eye contact, follow
the instructions below.
Warning! The battery uid may cause
personal injury or damage to property. In
case of skin contact, immediately rinse
with water. If redness, pain or irritation
occurs seek medical attention. In case of
eye contact, rinse immediately with
clean water and seek medical attention.
Chargers
Your charger has been designed for a
specic voltage. Always check that the
mains voltage corresponds to the voltage
on the rating plate.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
uUse your Black & Decker charger
only to charge the battery in the
appliance/tool with which it was
supplied. Other batteries could burst,
causing personal injury and damage.
uNever attempt to charge non-
rechargeable batteries.
uIf the supply cord is damaged, it must
be replaced by the manufacturer or
an authorised Black & Decker
Service Centre in order to avoid a
hazard.
uDo not expose the charger to water.
uDo not open the charger.
uDo not probe the charger.
uThe appliance/tool/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Your charger has been designed for a
specic voltage. Always check that the
mains voltage corresponds to the voltage
on the rating plate. Never attempt to
replace the charger unit with a regular
mains plug.
Symbols on the charger
#Your charger is double insulated; therefore no earth
wire is required.
Fail safe isolating transformer.
The mains supply is electrically
separated from the transformer
out put.
The charger automatically
shuts off if the ambient
temperature becomes too high.
As a consequence the charger
will be inoperable. The unit
must be disconnected from the
mains supply and taken to an
authorised service centre for
repair.
$The charger is intended for indoor use only.
Read the manual carefully
before using the appliance.
Warning! Keep electrical appliances out
of reach from children or inrm persons.
Do not let them use the appliances
without supervision.

7
Features
1. On/off switch
2. Dust bowl
Fig. A
3. Crevice tool
4. Wet pick-up accessory
Unpacking
Identifying your product
The model design can be determined
from the sufx codes used in the
catalogue number. The following
catalogue numbers are described in this
manual: NW36XXY H2/NW48XXY H2
The sufx code XX corresponds to the
following designs:
00: stick handle, no accessories supplied
03: loop handle, supplied with crevice
tool and brush tool
60: loop handle, supplied with crevice
tool and wet pick-up accessory
The sufx code Y is used to identify the
range of colour options. The sufx code
Y represented by the letter N is used for
models with an NiMH battery.
Installation
Fitting the charging base to the
wall (g. C1 & C2)
The charging base can be placed on a
worktop or tted to the wall to provide a
convenient storage and charging point
for the appliance.
Assembly
Fitting the accessories (g. A & D)
The appliance is supplied with the
following accessories:
u a crevice tool (3) for conned spaces
ua wet pick-up accessory (4) for wet
spills
To t an accessory, proceed as follows:
uTake the accessories from the
appliance.
uInsert the appropriate accessory into
the front of the appliance.
You may ret the other accessory by
clicking it into the accessory holder.
To ret both accessories:
uPush the accessories down until they
click into place.
Use
uThe appliance can be charged while
placed on a worktop or hung on the
wall using the wall hook provided.
u Before rst use, the battery must be
charged for at least 24 hours.
uLeave the appliance connected to the
charger whenever it is not in use.
Charging the battery (g. B)
uMake sure that the appliance is
switched off. The battery will not be
charged with the on/off switch in the
on position.
uFit the appliance properly on the
charger aligning the arrow on the
charger with the split of the
appliance.
uPlug in the charger.
uSwitch on at the mains.
uLeave the appliance to charge for at
least 24 hours.
Whilst charging, the charger may
become warm. This is normal and does
not indicate a problem. The appliance
can be left connected to the charger
indenitely.
Warning! Do not charge the battery at
ambient temperatures below 10 °C or
above 40 °C.
Switching on and off (g. E)
uTo switch on, slide the on/off switch
(1) forward.
uTo switch off, slide the on/off switch
back.

8
Wet pick-up (g. A)
Use the wet pick-up accessory (4) on
non-absorbent surfaces.
For best results when using this
accessory, hold the appliance at an angle
of 45° and pull it slowly towards you.
On absorbent surfaces, such as carpet,
your appliance will pick up wet spills
better without the accessory.
Cleaning and maintenance
Warning! Regularly clean the lters.
Cleaning the dust bowl and lters
(g. F & G)
The lters are re-usable and should be
cleaned regularly.
uRemove the dust bowl (2) by turning
counterclockwise.
uEmpty the dust bowl.
u Remove the lters (5 & 6).
u Wash the lters in warm, soapy
water. The bowl can also be washed
if necessary. Do not immerse the
appliance in water.
u Make sure the dust bowl and lters
are dry.
u Ret the lters (5 & 6).
u Ret the dust bowl onto the
appliance. Make sure the dust bowl
clicks into place.
Warning! Never use the appliance
without the lters. Optimum dust
collection will only be achieved with clean
lters and an empty dust bowl.
Replacing the lters
The lters should be replaced every
6 to 9 months and whenever worn or
damaged. Replacement lters are
available from your Black & Decker
dealer (catalogue number: WVF60).
u Remove the old lters as described
above.
u Fit the new lters as described above.
Protecting the environment
ZSeparate collection. This product must not be disposed of with
normal household waste.
Should you nd one day that your
Black & Decker product needs
replacement, or if it is of no further use to
you, do not dispose of it with household
waste. Make this product available for
separate collection.
zSeparate collection of used products and packaging allows
materials to be recycled and
used again. Re-use of recycled
materials helps prevent
environmental pollution and
reduces the demand for raw
materials.
Local regulations may provide for
separate collection of electrical products
from the household, at municipal waste
sites or by the retailer when you
purchase a new product.
Black & Decker provides a facility for the
collection and recycling of Black & Decker
products once they have reached the end
of their working life. To take advantage of
this service please return your product to
any authorised repair agent who will
collect them on our behalf.
You can check the location of your
nearest authorised repair agent by
contacting your local Black & Decker
ofce at the address indicated in this
manual. Alternatively, a list of authorised
Black & Decker repair agents and full
details of our after-sales service and
contacts are available on the Internet at:
www.2helpU.com
Battery (g. H)
ZWhen disposing of the product, the battery must be removed
as described below and
disposed of in accordance with
local regulations.
If you want to dispose of the product
yourself, the battery must be removed as
described below and disposed of in
accordance with local regulations.

9
Warning! Disconnect the appliance from
the power supply before removing the
battery.
uDischarge the battery by operating
the appliance until the motor stops.
uTake the accessories from the
appliance.
uRemove the screws (7).
uOpen the appliance.
uRemove the battery and the attached
motor and switch module (8).
uUse a screwdriver to detach the
battery from the motor and switch
module.
uPlace the battery in suitable
packaging to ensure that the
terminals cannot be short-circuited.
uTake the battery to your service
agent or a local recycling station.
Warning! Once removed, the battery
cannot be retted.
Technical data
NW36XXY H2 NW48XXY H2
Voltage V 3.6 4.8
Battery type NiCd/NiMH NiCd/NiMH
Weight kg 0.9 0.9
Charger
*A050020D *A070015D
Model NW36 NW48
Input voltage VAC 230 230
Output voltage VAC 5 7
Amperage mA 200 150
Approx.
charging time h 24 24
Weight kg 0.3 0.3
Level of sound pressure according to EN 60704-1:
Sound pressure (L
pA
) < 70 dB(A), uncertainty (K) 3 dB(A)
European Community patent application
number: 000 540 745 & 000 540 752
European Community design application
number: 000 541 230 & 000 540 752
DUSTBUSTER is a registered trademark
of the Black & Decker Corporation.
Guarantee
Black & Decker is condent of the quality
of its products and offers an outstanding
guarantee. This guarantee statement is
in addition to and in no way prejudices
your statutory rights. The guarantee is
valid within the territories of the Member
States of the European Union and the
European Free Trade Area.
If a Black & Decker product becomes
defective due to faulty materials,
workmanship or lack of conformity, within
24 months from the date of purchase,
Black & Decker guarantees to replace
defective parts, repair products subjected
to fair wear and tear or replace such
products to ensure minimum
inconvenience to the customer unless:
uThe product has been used for trade,
professional or hire purposes;
uThe product has been subjected to
misuse or neglect;
uThe product has sustained damage
through foreign objects, substances
or accidents;
uRepairs have been attempted by
persons other than authorised repair
agents or Black & Decker service
staff.
To claim on the guarantee, you will need
to submit proof of purchase to the seller
or an authorised repair agent. You can
check the location of your nearest
authorised repair agent by contacting
your local Black & Decker ofce at the
address indicated in this manual.
Alternatively, a list of authorised
Black & Decker repair agents and full
details of our after-sales service and
contacts are available on the Internet at:
www.2helpU.com
Please visit our website
www.blackanddecker.co.uk to register
your new Black & Decker product and to
be kept up to date on new products and
special offers. Further information on the
Black & Decker brand and our range of
products is available at
www.blackanddecker.co.uk

TYP.
www.2helpU.com 20 - 01 - 10
E15951
NW3660(N) - NW4860(A)(N)
Partial support - Only parts shown available Nur die aufgefuerten teile sind lieferbar Reparation partielle - Seules les pieces indiquees sont disponibles Supporto parziale - Sono disponibili soltanto le parti evidenziate Solo estan disponibles las peizas listadas So se encontram disponiveis as pecas listadas Gedeeltelijke ondersteuning - alleen de getoonde onderdelen zijn beschikbaar
11
10
15
13
12
6
H2
NW3660(N) NW4860(N) NW4860A(N)
12

ENGLISH
Do not forget to register your product!
www.blackanddecker.co.uk/productregistration
Register your product online at www.blackanddecker.co.uk/productregistration or
send your name, surname and product code to Black & Decker in your country.

Australia
Black & Decker (Australia) Pty. Ltd. Tel. [phone]
20 Fletcher Road, Mooroolbark, Fax [phone]
Victoria, 3138
New Zealand
Black & Decker Tel. [phone]
5 Te Apunga Place Fax [phone]
Mt Wellington
Auckland 1060
United Kingdom
Black & Decker Tel. [phone]
210 Bath Road Fax [phone]
Slough, Berkshire SL1 3YD Helpline 01753 574277
S/T-01/1090559290 REV 0