Black Widow Security BW FM 200 K User manual

Standard Features
The system has the following standard features:
• (1) 3-button LCD display remote control
• Status indicator (LED)
• Program/Valet switch
• Remote Start capabilities
• Extended Range Transceiver
• Valet mode
• Active arming
• Stop & Go Feature
• Auto Cold Start
• Remote keyless entry (Door lock/unlock)
• Hood protection
• Doggie Door release
• Window roll-down
Note: Some features may not be appropriate
for certain vehicles. Automatic transmission
and electronic fuel injection are required on
vehicles for use with this system.
Security System Operation
ARMING OPERATION
To arm the system press
transmitter button 1:
• The siren will chirp
once.
• The parking lights will
flash once.
• The doors will lock*.
• The L.E.D. will turn solid for 2 seconds
then start flashing slowly. After 10
seconds the system is armed.
*If Installed
DISARMING OPERATION
To disarm the system press
transmitter button 1.
• The siren will chirp
twice.*
• The parking lights will
flash twice.
1
K9 SECURITY/REMOTE START SYSTEM
OWNERS MANUAL
Press
Press

• The doors will unlock.
• The optional illuminated entry feature
will turn on the dome light for 30 seconds.
*In the event the alarm was triggered while away, the
system will respond with 3 chirps and 3 parking light
flashes.
To enter the Valet Mode:
1. Be sure the system is disarmed.
2. Turn the ignition key on.
3. Press and hold the valet/service
mode switch for 3 seconds.
• The LED will turn on solid indicating
the system is in Valet Mode.
To exit Valet Mode:
1. Turn the ignition key on.
2. Press and hold the valet/service mode
switch for 3 seconds.
• The LED will turn off.
• The Siren will chirp 2 times.
EMERGENCY OVERRIDE
If the transmitter becomes lost or fails to
operate, the system can be disarmed by using
the emergency override feature.
To override the system:
1. Enter the vehicle.
• Because the system is armed, the
siren will sound.
2. Turn on the ignition key.
3. Press the Valet/Service Mode switch.
• The siren will stop sounding.
TRUNK RELEASE
Press button 3 for approx-
imately 2 seconds to open
the trunk.
Remote Start Operation
Important: The system should be placed
into the valet mode when parked inside a
garage or being left for service. Only start
the vehicle in a well ventilated area. Do
not use in a closed garage or indoors. Be
sure to familiarize yourself with all
features prior to using this product.
REMOTE STARTING THE VEHICLE
To remote start the vehicle:
Press button 2 on the transmitter.
• The siren chirps 3 times.
• The parking lights turn
on.
• Approximately 2
seconds later the
system will attempt
to start the vehicle.
• Once the car has started, the heater or
air conditioner will turn on and run for
the preprogrammed time (15 or 25
minutes). If the engine fails to start on
the first attempt, it will repeat the
starting procedure 2 more times. If the
vehicle fails to start after a total of 3
times the siren will chirp 4 times.
Driving vehicle after Remote Starting:
Unlock the door by pressing button 1 on the
remote transmitter. Enter vehicle, turn
ignition key to the on position (Note:Do not
turn the key all the way to the start position as
you may damage the starter).
Once the ignition key is turned to the on
position, press the brake pedal and shift the
car into the proper gear and you may now
drive the vehicle (Note:If brake pedal is
pressed prior to turning on ignition, engine will
turn off).
2
Press
Press

REMOTE ENGINE SHUTDOWN
If the vehicle has been remotely started and
you desire to turn the vehicle off, simply
press button 2 on the remote transmitter.
After the motor has turned off the doors will
relock (optional).
AUTO COLD START
Cold start feature allows the remote starter
to start and run the vehicle every one or two
hours (selectable by your installer) for a
period of 24 hours.This allows the engine to
remain at an operational temperature in
extremely cold weather. Auto Cold Start must
be enabled during installation or it cannot be
engaged.
Engaging the Auto Cold Start feature:
To turn Auto Cold Start on:
While holding the brake pedal down, push
the program switch and transmitter button 2
for two seconds.
• The parking lights will flash three times.
• The siren will chirp three times.
• The engine will start and run for thirty
seconds to indicate the Cold Start
feature is engaged.
Disengaging the Auto Cold Start feature:
The Auto Cold Start feature can be
deactivated in one of three ways:
• Press the brake pedal.
• Turn on the ignition.
• Remote start the vehicle using the
transmitter.
STOP AND GO
The Stop and Go feature allows the vehicle
to remain running without use of the ignition
key during short stops.
To activate the Stop and Go feature:
1. Press and hold the brake pedal.
2. While pressing the brake pedal, push
transmitter button 1.
• The LED will flash rapidly.
• The parking lights will flash four
times.
3. Release the brake pedal.
4. Remove the key from the ignition
switch.
5. Exit the vehicle and lock the doors
manually or using transmitter button 1*.
To resume driver control:
1. Unlock the doors manually or by press-
ing transmitter button 1.*
2. Turn on the ignition.
3. Press the brake pedal.
• The vehicle resumes driver control.
• The LED will turn off.
*If optional keyless entry feature is installed.
SAFETY FEATURES
The system will not start the vehicle if the
brake pedal is pressed or the hood is open.
Also, if the brake is pressed or the hood is
opened while remote running, the remote
start will shut down.
REPLACING LOST OR STOLEN
REMOTE TRANSMITTERS
The system can “learn” a maximum of 2 LCD
transmitters.To add a transmitter or replace
lost/stolen transmitters, please consult with
an authorized dealer.
3

4
© David Levy Company, Inc., k9SECURITY/Rev. 1, 07/01
DLC/U.S.A. 12753 Moore Street • Cerritos, California 90703
DI
ARM
UNLOCK
LOCK
SVC
O.K.
Door -
If a door is opened while the
system is armed, the icon
will be displayed, the doorframe
will animate, and the icon
will be displayed.
Start -
The display will show the
icon and the icon to indicate
the ignition is turned on and
the engine is going to crank.
When the engine starts and
continues to run, the icon
will be displayed, the exhaust
icon will flash and the icon
will rotate.
Doggie Door -
The display will flash the
icon opening to confirm
trunk operation.
Disarm -
The display will flash the
icon and the animated
to confirm disarming. If the
alarm was triggered while away
the icon will be displayed.
Arm
Start
Trunk
K9 SECURITY/REMOTE START SYSTEM
Transmitter Operation
ARM
DIS
ARM
LOCK
UNLOCK
Button
I
II
III
II III
+
Operation
ARM/DISARM/PANIC Button - T o arm or disarm the
system, press button 1.To activate the panic feature, press
button 1 and hold for three seconds.
Doggie Door - To activate the trunk output, press button 3.
STATUS CHECK - To check current status of the system,
press buttons 2 and 3 together.The current status of the system
will be displayed on the transmitter.
Transmitter Confirmation Indications
Arm -
The display will flash the
icon and the animated
icon to confirm arming.
Note: Some icons that appear on the transmitter
are reserved for future use and have no functions
at this time.
LOCK
ARM
START Button - To start the vehicle, press and hold button
2 for two seconds.To shut down the vehicle, press button 2
and hold for two seconds.
UNLOCK
DIS ARM