Black Widow Security BW FM 6150 User manual

1
REMOTE START SECURITY SYSTEM
OWNERS MANUAL
Standard Features
The System has the following standard features:
• 5-button remote transmitter
• Status indicator (LED)
• Valet/Service mode switch
• Remote Start capabilities
• Extended Range Receiver
• Multi-tone siren (120dB)
• Dual stage impact detector
• Remote panic
• Valet mode
• Remote chirp delete
• Remote sensor bypass
• Passive or active arming
• Stop & Go Feature
• Auto Cold Start
• Flashing parking lights
• Auto Rearm
• Passive/Active Arming
Optional Features
This System has many optional features that may
require additional parts and/or labor. Please contact
your dealer for more details.
• Remote keyless entry (Door lock/unlock)
• Illuminated entry
• LCD FM 2-way Remote
• Hood & trunk protection
• Horn honk
• Trunk/hatch release
• Window roll-up
• Back up battery
• Additional sensors: glass breakage/microwave
Note: Some features may not be appropriate for
certain vehicles. Automatic transmission and
electronic fuel injection are required. on vehicles for
use with this system.
REMOTE TRANSMITTER FUNCTIONS
Button 1 Arms the system and locks the
doors*. Button 1 also activates the Panic
feature.
Button 2 Disarms the system and unlocks the
doors*.
Button 3 Activates the optional Trunk Release
feature*.
Button 4 Activates the Remote Start Feature.
Button 5 Auxiliary Shift Key.
Buttons 5 then 4 Activates the 2nd auxiliary
function.
*Optional Feature
5-Button
Transmitter
Button 1
Button 3
Button 2
Button 4
Button 5

Security System Operation
ARMING OPERATION
To arm the system press transmitter button 1:
• The siren will chirp once.
• The parking lights will flash once.
• The doors will lock*.
• The L.E.D. will turn solid for 10 seconds
then start flashing slowly, the system is
now armed.
While the system is armed the alarm will
trigger if:
• A door is opened.
• The hood/trunk is opened*.
• The shock sensor detects an impact to the
vehicle.
When the alarm is triggered the siren will
sound, the parking lights will flash, and the horn
will honk*. If the alarm is triggered while the
remote start is engaged, the remote start will
immediately shut down.
PASSIVE ARMING
The passive arming feature allows the system to
arm automatically without user intervention.
This programmable feature may be enabled during
installation.
To arm the system passively:
1. Turn the ignition key off.‡
2. Exit the vehicle and close all doors.
• The LED will start flashing rapidly to
indicate that the system is preparing to
arm. (The system can be armed at any
time by pressing transmitter button 1.)
• The siren will chirp 30 seconds after
the last door is closed to indicate the
system is now armed.
• The doors will lock.†*
‡The ignition must have been on for at least 10 seconds prior
to exiting the vehicle or Passive Arming will be bypassed.
†If the Passive Locking feature was enabled during installation.
DISARMING OPERATION
To disarm the system press transmitter button 2.
• The siren will chirp twice.¥
• The parking lights will flash twice.¥
• The doors will unlock.†*
• The dome light will turn on for 30
seconds.*
¥If the alarm was triggered while away, the system will respond
with 3 chirps and 3 parking light flashes.
†If the Passenger Unlock Feature is enabled, pressing the
unlock button will unlock only the driver's door. Pressing the
unlock button again unlocks all doors.
TAMPER ALERT
If the alarm was triggered while away from the
vehicle, the siren will chirp 3 times on disarm-
ing for tamper indication. After disarming the
alarm, enter vehicle and turn ignition on. The
LED will flash the zone that was triggered 5
times (see LED chart).
AUTO REARM
The Auto Rearm feature allows the system to
automatically re-arm itself in the event the
system is disarmed and ignition is not turned on
within 30 seconds.
NOTE: This programmable feature may be disabled
during installation. The Passive Arming feature and
Auto Rearm feature are related. In order to disable
the Auto Rearm feature, the Passive Arming feature
must also be disabled during installation. This
feature will not work on vehicles with the illuminated
entry feature enabled.
SILENT ARMING/DISARMING
Press transmitter button 5 (the Shift Button)
then the Arm or Disarm button for one-time
silent operation.
*Optional Feature
2

CHIRP DELETE
For full time silent operation, the ARM/ DISARM
chirps can be permanently disabled. This feature
must be programmed during installation.
IGNITION LOCK*
The ignition locking feature allows the doors to
automatically lock when the ignition key is
turned on, and automatically unlock when the
ignition key is turned off. This feature may be
disabled during installation.
REMOTE PANIC
In the event of an emergency (PANIC) situation,
the system’s siren can be triggered for 45
seconds to attract attention.To activate the Panic
Feature, press transmitter button 1 for 3
seconds:
• The siren will sound.
• The parking lights will flash.
Press button 1 to exit panic mode and rearm
the system. Press button 2 to exit panic mode
and disarm the system. The Panic Feature will
operate when the ignition is on.
EMERGENCY OVERRIDE
If the transmitter becomes lost or fails to
operate, the system can be disarmed by using
the emergency override feature.
To override the system:
1. Enter the vehicle.
• Because the system is armed, the siren
will sound.
2. Turn on the ignition key.
3. Press the Valet switch for 5 seconds.
• The siren will stop sounding.
• Starter defeat bypassed.
VALET MODE
When the system is placed into theValet Mode
the security system will be disabled.
However, the optional keyless entry and trunk
release and remote start features will still
function if installed.
NOTE: Remote Start feature maybe disabled
during valet mode if programmed during
installation.
To enter the Valet Mode:
1. Be sure the system is disarmed.
2. Turn the ignition key on.
3. Press and hold the valet/service mode
switch for 3 seconds.
• The siren will chirp once.
• The LED will turn on solid indicating
the system is in Valet Mode.
To exit Valet Mode:
1. Turn the ignition key on.
2. Press and hold the valet/service mode
switch for 3 seconds.
• The LED will turn off.
• The Siren will chirp 2 times.
OPTIONAL TRUNK RELEASE
Press button 3 for approximately 2 seconds to
open the trunk.
OPTIONAL TRUNK DISARM
The trunk disarm feature allows the alarm to
disarm automatically whenever transmitter
button 3 is used to activate the optional trunk
release. This eliminates having to first disarm
the alarm before activating the trunk release.
NOTE: This feature must be programmed during
installation.
REMOTE SENSOR BYPASS
To arm the system and bypass the shock sen-
sor, press button 1 to arm, then within 2 sec-
onds press button 1 again. The siren will chirp
5 times and sensors will be ignored until the
3
*Optional Feature

system is disarmed and rearmed.
OPTIONAL SECURE
OVERRIDE CODE
If your system was programmed to override
with a personal override code-pressing the
override switch from 1 to 15 times.
To disarm the system with your personal over-
ride code please use the following steps:
1. Open Door, Alarm system will trigger
2.Turn ignition key to on
3. Press the override switch to the selected
number of times and hold on the last one for
5 seconds until the alarm turns off.
Remote Start Operation
Important: Only start the vehicle in a
well ventilated area. Do not use in a
closed garage or indoors. Be sure to
familiarize yourself with all features
prior to using this product.
REMOTE STARTING THE VEHICLE
To remote start the vehicle:
Press transmitter button 4 for 3 seconds.
• The parking lights turn on.
• Approximately 2 seconds later the
system will attempt to start the vehicle.
• Once the car has started, the heater or
air conditioner will turn on and run for
the pre-programmed time (15 or 25
minutes). If the engine fails to start on
the first attempt, it will repeat the
starting procedure 2 more times. If the
vehicle fails to start after a total of 3
times the system will shut down.
Driving vehicle after Remote Starting:
Unlock the door by pressing button 2* on
the remote transmitter. Enter vehicle, turn
ignition key to the on position (Note:Do not
turn the key all the way to the start position as
you may damage the starter).
Once the ignition key is turned to the on
position, press the brake pedal and shift the
car into the proper gear and you may now
drive the vehicle (Note:If brake pedal is
pressed prior to turning on ignition, engine will
turn off).
REMOTE ENGINE SHUTDOWN
If the vehicle has been remotely started and
you desire to turn the vehicle off, simply press
and hold button 4 on the remote transmitter
for three seconds. After the motor has
turned off the doors will relock*. This feature
must be programmed during installation.
AUTO COLD START
This feature allows the system to start and
run the vehicle every one or two hours
(selectable by your installer) for a period of
24 hours.This allows the engine to remain at
an operational temperature in extremely
cold weather. Auto Cold Start must be enabled
during installation or it cannot be engaged.
Engaging the Auto Cold Start feature:
To turn Auto Cold Start on:
1. Press and hold the brake pedal.
2. While holding the brake pedal down,
push the Valet switch and transmitter
button 2 for two seconds.
• The parking lights will flash four times
to indicate the Cold Start feature is
engaged.
3. Release the brake pedal.
4
*Optional Feature

5
Disengaging the Auto Cold Start feature:
The Auto Cold Start feature can be
deactivated in one of three ways:
• Press the brake pedal.
• Turn on the ignition.
• Remote start the vehicle using the
transmitter.
STOP AND GO
The Stop and Go feature allows the vehicle
to remain running without use of the ignition
key during short stops.
To activate the Stop and Go feature:
1. With engine running push transmitter
button 4 (on FM 2-way press button 2.).
• The parking lights will turn on.
2. Remove the key from the ignition.
3. Exit the vehicle and lock the doors
manually or using transmitter button 1*.
To resume driver control:
1. Unlock the doors manually or by
pressing transmitter button 2*.
2. Turn on the ignition.
• The vehicle resumes driver control.
SAFETY FEATURES
The System will not start the vehicle if the
brake pedal is pressed or the hood is open.
Also, if the brake is pressed or the hood is
opened while remote running, the remote
start will shut down.
REPLACING LOST OR STOLEN
REMOTE TRANSMITTERS
This System can “learn” a maximum of 4
remote transmitters.To add a transmitter or
replace lost/stolen transmitters, please
consult with an authorized Black Widow
Dealer.
*Optional Feature

6
© DLC, Inc., 65-7150 Rev. 1, 09/02
SYSTEM REFERENCE INDICATORS
STATUS INDICATOR (LED) FUNCTIONS
On Solid = Valet Mode
Slow Flash = System Armed
Rapid Flash = Passive Arming
TAMPER ALERT LED FUNCTIONS
1 flash = sensor #2
2 flashes = shock sensor
4 flashes = door
5 flashes = hood or trunk
flash-flash-pause-flash-flash-pause = shock sensor
PARKING LIGHTS FUNCTIONS
On Solid = Vehicle Remote Starting
Flash 1x = System armed
Flash 2x = System disarmed
Flash 3x = Tamper indication (after disarming)
Flash 4x = Defective zone warning
(after arming)