Black BLK-CDS105NH Manual

INFORMATION - This equipment has been tested and found to comply with
limitsforaClassAdigitaldevice,pursuanttopart15ofthe FCCRules&CERules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
◆ Do NOTuse power sources other than those specified.
◆ Do NOTexpose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
1
Super DNR High Resolution Day/Night Camera

■Contents
Features
Precautions
Overview
Installation Procedures
■Front View
■Side View
■Bottom View
■Rear View
04
06
09
13
09
10
11
12
■Lens
ㆍWhen Using Auto Iris Lens
ㆍWhen Using C/CS Mount Lens
■Connecting a Monitor
■Connecting Power
■Control via RS-485 Interface
13
17
18
19
Components and Accessories 08
How to Use the Camera
Troubleshooting
■Function Menu Structure
■How to Set up the Functions
ㆍLENS
ㆍEXPOSURE
ㆍWHITE BALANCE control
ㆍBACKLIGHT
ㆍDNR (Digital Noise Reduction)
ㆍDAY/NIGHT
ㆍIMAGE ADJ
ㆍSPECIAL
ㆍEXIT
20
39
20
21
22
24
26
27
29
30
32
34
38
Specifications 41
2
3
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera

■Features Warning ■
Ultra High Resolution
By adopting a double-speed 410,000 pixel
SonyCCD,thecameraproducesclearpicture
quality withahorizontalresolutionof 580 TV lines
for color,and700TVlinesforB/W.
Excellent Sensitivity
AdoptingaDiagonal 6mm (1/3"),highlysensitive
CCD anddigitalsignalprocessing technology,
it can clearly distinguish the outline and color
of a subject in an extremely low luminance
environment.even, for example, understarlight.
Sincesurveillanceispossibleinplaceswhere
the lightispoor, the cameraisappropriatefor
dayandnightsurveillanceoutdoors oronthe
outside of buildings.
DNR (Digital Noise Reduction)
Theamountoflowilluminancenoise has been
significantly reduced, and the signal-to-noise
ratio(S/Nratio)aswellashorizontalresolution
have been improved, resulting in a clear and
sharp image display even in the dark.
Day & Night
Thecameraidentifieswhetheritisdayornight
and automaticallyswitchestotheappropriate
mode,depending on its environment.Byday,
thecameraswitchestocolormodeinorderto
maintain optimal color. At night, it switches to
B/Wmodesoastoobtainbetterpicturedefinition.
Motion Detection
Since thecameradetectsmotionandgenerates
signalswithoutanyadditionalexternalsensors,
you can monitor activity more efficiently by
connecting the camera to an alarm device.
DIS (Digital Image Stabilizer)
TheDISfunctioncompensatesforanycamera
movement, to produce more stable pictures.
Video/DC Drive Lens Support
You can select Video or DC Drive Lens from
the menu.
Miscellaneous Functions
SYNC(INT/LL),SENS-UP,FREEZE,FLIP
(H/V-REV), D-ZOOM, SHARPNESS, MOTION
DETECTIONandPRIVACYfunctionsareprovided.
RS-485 Communication
Control Support
RemoteOSDmenucontrolviaanRS-485interface
issupported.
OSD
The camera control is convenient by using
7 different foreign language O.S.D.
-NTSC: Korean,English,Spanish,Japanese
- PAL : English, French, German, Spanish,
Italian, Chinese
The camera requires periodic inspection.
Contact an authorised technician to carry out the inspection.
Stop using your camera when you find it malfunctioning.
If the camera emits smoke or is unusually hot for a long period,
a fire may be caused.
Do not Install the camera on a surface that can not support it.
If the camera is installed on an inappropriate surface, it may fall
and cause injury.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not dis-assemble the camera.
It may result in an electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in a fire or other hazards.
4
5
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera

■Precautions
Do not install the camera in
extreme temperature conditions.
Do not install the camera under
unstable lighting conditions. Do not touch the front lens of the
camera.
Only use the camera under conditions
where temperatures are between
-10 C and +50 C. Be especially
careful to provide ventilation when
operating under high temperatures.
It can cause the image quality to be
poor.
Severe lighting change or flicker can
cause the camera to work improperly.
This is one of the most important parts of
the camera. Be careful not to leave
fingerprints on the lens cover.
Do not install or use the camera in an
environment where the humidity is high.
ㆍIf the camera is exposed to spotlight or object reflecting strong light,
smear or blooming may occur.
ㆍPlease check that the power satisfies the normal specification before
connecting the camera.
It can cause malfunctions to occur.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that
corrode the electronic components.
If exposed to radioactivity the CCD
will fail.
It can damage the CCD.
Do not drop the camera and protect
it from physical shocks.
Do not expose the camera to rain
or spill beverage on it. Do not expose the camera to radioactivity.
Never keep the camera pointed
directly at strong light.
6
7
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera

■Components and Accessories Overview ■
2. Auto Iris Lens Connector Plug
3. C-Mount Adapter
4. Instruction Manual
1. Ultra High Resolution
Color CCD Camera
① Tripod Mounting Bracket Screw Hole
Used to fix the Tripod Mounting Bracket to the top of the camera.
② C-Mount Lens Adapter
Install this adapter to use a C-Mount Lens.
Front View
8
9
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera
①
②
③
③ Back Focus clamp screw
Loosen the clamp screw with a screwdriver before adjusting
the Back Focal length.

■Overview
⑤ Tripod Mounting Bracket Screw Hole
Used to fix the camera on a bracket or tripod.
The screw sizes for this hole are as follows:
④ Auto Iris Lens Connector
Used to connect Auto Iris Lens plug.
Side View Bottom View
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
L
④
10
11
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera
⑤

■Overview Installation Procedures ■
12
13
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera
Note
Lens
The lens is not supplied with this camera. Purchase a lens suitable for
your environment. This camera accepts the auto iris lens and both
C-and CS-mount lens.
• It is recommended to use the DC type Auto Iris Lens to effectively
enjoy the major functions of this camera.
• Keep the lens surface clean, since if it is contaminated with dirt or
fingerprints the picture quality suffers.
When Using Auto Iris Lens
1. Strip the insulation of the auto iris lens cable 8mm from the end..
2. Strip the insulation of the core of the auto iris lens cable to expose a
2mm length.
⑥Function Setup Button
ㆍSET Button : Displays the menu on the screen. Press this button to confirm
status or after changing a selected item.
ㆍUp and Down Button : Used to move the cursor up or down in the menu
screen to select a desired menu item.
ㆍLeft and Right Button : Used to move the cursor left or right in the menu
screen or to change the value of the selected item.
⑦D & N Input Port (GND : BW, Open : Color)
You can switch to Day & Night Mode by connecting an external signal to this port.
⑧MD Output Port
Motion detection signals are output through this port.
⑨RS-485 Control Port
You can control SETUP MENU through this port by using external controllers like a
Remote controller that RS-485 Communication is supported. For details, see page 19.
⑩Power LED
When power is properly connected, this LED comes on.
3±0.5sec
0V
There is motion
+4.0V ~ +4.5V (less than 10mA)
There is motion
⑫Auto iris lens selection switch
Change the mode to DC or VIDEO depending on the type of auto iris
lens being used.
⑬Power IN Port
Connect the power as specified for each model here.
approx. 8mm
approx. 2mm
⑭Video OUT Port (UTP Cable)
For details, see page 19.
Rear View
REMOTE
VIDEO OUT
DC VIDEO
POWER
SET
F.G
AC24V/DC12V
D/N
IN GM/D OUT
UTP
OUT
RS485
⑥
⑦
⑧
⑨
⑩
⑪
⑬
⑫
⑭
⑪Video OUT Port (Coaxial Cable)
Videosignals are outputthrough thisport. Connect this port tothe VideoIN port ofa monitor.

■Installation Procedures
3. Remove the cover of the auto iris lens connector plug and solder the lens
cable to the connector pin of the plug.
4. Fit the cover of the auto iris lens connector plug, remove the protective
glass cover from the front of the camera, and fasten the auto iris lens
by turning it clockwise.
• For a Video Drive Lens
Pin 1: Red (Power)
Pin 2: NC
Pin 3: White (Video Signal)
Pin 4: Black (Ground)
• For a DC Drive Lens
Pin 1: Damping -
Pin 2: Damping +
Pin 3: Drive +
Pin 4: Drive -
When Using C/CS Mount Lens
Beforeinstallingalens,identify whetherthelenstobeinstalledisa C-Mount
orCS-Mount.Thiscameraissetfor aCS-MountLensbydefault.Toinstalla
C-Mount Lens, a simple modification is required.
•WhenUsingaCSMountLens
Removetheprotectiveglasscoveratthefrontofthisproductandturnthe
CSMountLensclockwisetoinstallit.AndsetfocusofcamerausingBack
FocusControlLeverofcamerasideaftercombiningCS-Mount lens.
• Use the lens connector shown in the following figure. If the dimensions
of the connector are not correct, it may damage the camera, or the lens
may not be installed firmly.
• If thelensistoo heavy, thecamerabecomesunbalanced and theremay
be problems. Use a lens that weighs less than 450g.
• When adjusting the Automatic Level Control (ALC) of an auto iris lens,
useAvmodeifavailable.Ifyouuse thePkmode,thepicturebrightness
may change continuously.
Note
connector
Lens cable
No. 3 Pin
No. 1 Pin No. 4 Pin
No. 2 Pin
C-Mount Lens: 10mm or less
CS-Mount Lens: 5mm or less
14
15
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera

REMOTE
VIDEO OUT
DC VIDEO
POWER
SET
F.G
AC24V/DC12V
D/N
IN GM/D OUT
UTP
OUT
RS485
REMOTE
VIDEO OUT
DC VIDEO
POWER
SET
F.G
AC24V/DC12V
D/N
IN GM/D OUT
UTP
OUT
RS485
■Installation Procedures
• When Using a C Mount Lens
1. Remove the protective glass cover at the front of this product and turn the
CMount Adapter clockwise to install it.
2. Turn the C-Mount lens clockwise to install it.
3. Set focus of camera using Back Focus Control Lever of camera side after
combining C-Mount lens.
Connecting a Monitor
ConnecttheVideoOUTportontherearpanelofthe cameratoa monitor.
• Sincetheconnectionproceduremay differdependingonthetypeofmonitor
orperipheraldevicetobeconnected,refertotheUserManualfor the device
tobeconnected.
• Makesuretoturnoffthedevice tobeconnectedbeforemakinganyconnections.
•Turnthe75Ω/Hi-ZswitchesofinterimdisplaydevicestotheHi-Zposition,
andthe switchesofany finaldevicetothe75 position.
CCDCamera
Monitor
CCDCamera
End monitor
Intermediate
16
17
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera

REMOTE
VIDEO OUT
DC VIDEO
POWER
SET
F.G
AC24V/DC12V
D/N
IN GM/D OUT
UTP
OUT
RS485
■Installation Procedures
Since power specifications differ depending on the model, make sure to check
your model name and specifications before connecting power.
You can connect power as shown in the following figure.
• Sincethepower specification supports bothACandDC,connectAC24V,500mA
Adaptor or DC 12V, 500mA Adaptor.
When the resistance value of copper wire is at [20°C(68°F)]
• As shown in the table above, voltage decreases as the wire gets longer.
Therefore use of an excessively long adaptor output line for connection to
the camera may affect the performance of the camera.
※Standard voltage for camera operation : DC 12V±10%, AC 24V±10%
※ There may be some deviation in voltage drop depending on the type of wire
and the manufacturer.
Control via RS-485 InterfaceConnecting Power
For AC / DC power
RS-485 Control Port
485 Control Board Connection Port
485+
(+) CONNECTION TERMINAL (TRX+)
(- ) CONNECTION TERMINAL (TRX-)
485-
Item
Initialvalue
PET PKT
UART MODE
BAUD RATECamera ID
1ENABLE 8-NONE-19600
#24(0.22mm2)
Copperwiresize(AWG)
#22(0.33mm2) #20(0.52mm2) #18(0.83mm2)
Resistancevalue( /m)
0.0180.030
0.050
0.078
Voltagedrop(V/m) 0.0060.0110.0180.028
ThecameracanbecontrolledbyusingexternalcontrollerslikeaRemotecontroller.
(RS-485Communication)
• TocontrolusingaDVR orSystemController
ConnecttheRS-485cable(TRX+,TRX-)totheconnectionportofthe485
controlboardthatisconnectedtothe DVRorSystemController.
* RS-485 Communication establishment initial value
• To control the camera by constructing an additional controller, use
Pelco-D protocol.
(Go Preset 95 : Enters into OSD menu or Set key function)
Note
18
19
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera
When using UTP Cable
• Connect UTP(Unshield Twisted Pair) wire to the UTP output of the camera
directly. UTP transmitter is included in the camera therefore additional UTP
transmitter is not necessary.
• UTP receiver is necessary to connect UTP wire to Monitor or DVR.
• When connecting UTP wire, make sure the polarity of the video signal
is correct.
• Use UTP wire "CAT 24AWG" to have the best transmission quality.

REMOTE
VIDEO OUT
DC VIDEO
POWER
SET
F.G
AC24V/DC12V
D/N
IN GM/D OUT
UTP
OUT
RS485
■How to Use the Camera
How to Set up the FunctionsFunction Menu Structure
You can set up functions using the 5 buttons on the rear of the camera.
1. Press the SET button.
• Main setup menu is displayed on the monitor screen.
2. Select a desired function using the Up and Down buttons.
• Place the cursor over a desired item.
Setup Menu
• DC • VIDEO • MANUAL
LENS
• SHUTTER • AGC • SENS-UP
• RETURN
EXPOSURE
• ATW • MANUAL • AWC SET
• OUTDOOR • INDOOR
WHITE BALANCE
• OFF • WDR • BLC
BACKLIGHT
• ON • OFF
DNR
• COLOR • B/W • AUTO
• EXTERN
DAY/NIGHT
• FREEZ • V-REV • H-REV
• D-ZOOM • SHARPNESS
• RETURN
IMAGE ADJUSTMENT
(IMAGE ADJ.)
• CAMTITLE • SYNC • MOTION DET
• PRIVACY • DIS • COMM ADJ
• LANGUAGE • RESET • RETURN
SPECIAL
EXIT
1. LENS DC
2. EXPOSURE
3. WHITE BAL ATW
4. BACKLIGHT OFF
5. DNR ON
6. DAY/NIGHT AUTO
7. IMAGE ADJ
8. SPECIAL
9. EXIT
MAIN SETUP
UP button
SET button
LEFT button
DOWN button
RIGHT button
20
21
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera

1. LENS DC
2. EXPOSURE
3. WHITE BAL ATW
4. BACKLIGHT OFF
MAIN SETUP
● DC/Video : Select Auto Iris Lens
• When DC is selected, you can control screen brightness. The range
of brightness control is between 1 and 70(40 in case of WDR mode).
Adjust the brightness appropriately for optimal screen brightness.
3. Set up a selected item by using the Left and Right buttons.
4. To finish the setting, select ‘EXIT’and press the SET button.
Using this function, you can control screen brightness.
1. When the SETUP menu screen is displayed, select LENS by using the Up
and Down buttons so that the arrow indicates LENS .
2. Select the connected lens type by using the Left and Right buttons. ●
Manual : Select Manual Lens
1. LENS DC
2. EXPOSURE
3. WHITE BAL ATW
4. BACKLIGHT OFF
5. DNR ON
6. DAY/NIGHT AUTO
7. IMAGE ADJ
8. SPECIAL
9. EXIT
MAIN SETUP
Select the function using
the UP or DOWN button. Change the status using
the LEFT or RIGHT button.
LENS
Note
■How to Use the Camera
• An item with the icon also has sub menus. To select a sub menu,
select an item with the icon and press the SETbutton.
• An item with the - - - icon is unavailable due to function settings.
Note
• Some lenses may not work properly, depending on the setting of the
BRIGHTNESS LEVEL.
• When Using a Video-Type Auto Iris Lens
① Adjust the ALC adjustment terminal on the lens appropriately. In
general, set it to AV (Average).
② It may not work properly depending on the installed lens. Set the
Level VR of the lens to the optimal value.
③ Set AGC / SENS-UP to OFF and adjust the Lens VR to an
appropriate brightness.
④ Adjust the Lens VR, adjust the BRIGHTNESS, and then check if
the screen brightness changes properly. Otherwise, adjust the Lens
VR again.
22
23
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera

1. LENS DC
2. EXPOSURE
3. WHITE BAL ATW
4. BACKLIGHT OFF
5. DNR ON
6. DAY/NIGHT AUTO
7. IMAGE ADJ
8. SPECIAL
9. EXIT
MAIN SETUP
1. When the SETUP menu screen is displayed, select EXPOSURE by using
the Up and Down buttons so that the arrow indicates EXPOSURE .
2. Select a desired mode using the Up and Down buttons.
● SHUTTER : You can select either auto or manual shutter.
- A.FLK : Select this when you experience picture flicker, which can happen
when there is a clash with the frequency of the installed lighting.
- ESC : Selectthis tocontroltheshutterspeedautomatically.IfESCisselected,
theshutterspeedisautomaticallycontrolleddependingontheambient
illumination of the subject.
- MANUAL: You can control shutter speed manually.
■How to Use the Camera
Note
• If you press the SETbutton in ‘AUTO’mode, You can adjust brightness
by increasing or decreasing the shutter speed. (X2~X256)
• Note that the higher the zoom level, the brighter the screen, but the
more likely it is that an after-image will appear.
• Although Noise, Spots, and Whitish symptoms may occur in SENS-UP
operation when the zoom level is increased, this is normal.
● AGC (AUTO GAIN CONTROL):
Thehigherthegain level,thebrighterthescreen-butthehigherthenoise.
- OFF : Deactivates the AGC function.
- LOW : Allows automatic gain control from 0 to 24dB.
- HIGH : Allows automatic gain control from 0 to 42dB.
● SENS-UP :
When it is night or dark, the camera
automatically detects the light level and
maintains a clear picture if this mode is
activated.
- OFF : Deactivates the SENS-UP function.
- AUTO : Activates the SENS-UP function.
● RETURN :
Select this to save the changes in the EXPOSURE menu and return
to the SETUP menu.
Note
• To produce better results with A.FLK, do not use it in conjunction with
the WDR mode of the BACKLIGHT menu.
• When the SHUTTER is set to ESC after selecting the Internal
Synchronization Type, the picture may become unstable if the camera
faces a bright fluorescent light. Therefore, take care when choosing
the installation position.
• ESC and MANUALmodes are only available together when the lens
is set to MANUAL.
• When the SHUTTER is set to MANUALor A.FLK mode, SENS-UP
will be disabled.
EXPOSURE
24
25
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera

1. LENS DC
2. EXPOSURE
3. WHITE BAL ATW
4. BACKLIGHT OFF
5. DNR ON
6. DAY/NIGHT AUTO
7. IMAGE ADJ
8. SPECIAL
9. EXIT
MAIN SETUP
Use the White Balance function to adjust the screen color.
1. When the SETUPmenu screen is displayed, select ‘White Bal.’by using the
Up and Down buttons so that the arrow indicates ‘White Bal.’.
2. Select a desired mode using the Up and Down buttons.
※ Select one of the following 5 modes, as appropriate for your purpose.
● ATW:Select thiswhenthecolortemperature isbetween1800°Kand10500°K
● INDOOR : Selectthiswhenthecolortemperatureisbetween4500°Kand8500°K.
● OUTDOOR:Selectthiswhenthe colortemperatureisbetween1800°Kand
10500°K. (sodium light inclusion)
● AWC→SET: Tofindtheoptimalsetting for the currentluminanceenvironment
inthismode,setthepointthecameratowardsa sheetof
whitepaper andpresstheSETbutton.Iftheenvironment
changes, readjust it.
● MANUAL: Select this to fine-tune White Balance manually. Set White
Balance first by using the ATW or AWC mode. After that switch
to MANUALmode, fine-tune the White Balance and then press
the SETbutton.
■How to Use the Camera
White Balance (White Bal.)
1. LENS DC
2. EXPOSURE
3. WHITE BAL ATW
4. BACKLIGHT OFF
5. DNR ON
6. DAY/NIGHT AUTO
7. IMAGE ADJ
8. SPECIAL
9. EXIT
MAIN SETUP
This camera is designed so that it delivers a distinctive subject and
background at the same time, even when the subject is in backlight, unlike
conventional cameras, by adopting a proprietary W-IV DSP chip.
1. When the SETUP menu screen is displayed, select 'BACKLIGHT' by using
the Up and Down buttons so that the arrow indicates 'BACKLIGHT' .
2. Select a desired mode using the Left and Right buttons depending on the
camera purpose.
Note
• White Balance may not work properly under the following conditions.
In this case select the AWC mode.
① When the color temperature of environment surrounding the subject
is out of the control range (e.g. clear sky, or sunset)
② When the ambient illumination of the subject is dim.
③ If the camera is directed towards a fluorescent light or is installed in
a place where illumination changes dramatically, the White Balance
operation may become unstable.
BACKLIGHT
26
27
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera

Thisfunctionreducesthebackgroundnoiseinalow luminanceenvironment.
1. When the SETUPmenu screen is displayed, select ’DNR’ by using
the Up and Down buttons so that the arrow indicates ’DNR’.
Note
• Because there can be a difference in the effectiveness of HLC
according to the amount of light area in the screen, optimize the
installation angle for the best HLC performance.
• In a dark environment, the HLC is only activated when a high light
that is larger than a certain area is present.
• The HLC is not activated in light or overly dark conditions.
DNR
2. Select a desired mode using the Left and Right buttons.
● OFF : Deactivates DNR. Noise is not reduced.
● ON : Activates DNR so that noise is reduced.
BLC ON BLC OFF
● BLC : Enables a user to directly select a desired area from a picture, and
to view the area more clearly.
● OFF : Not being used
● Select 'BLC' to adjust the area to be
enhanced and enhancement level.
● HLC : Enable a user to select a mask
color of high light area from a picture.
● HLC (High Light Compensation) :
If there is a high light installed in a limited environment such as an apartment
parking garage or gas station entrance, removing the high light makes it
possible to view car license plates efficiently.
- DAY : In normal daylight conditions, the HLC is not activated.
- NIGHT : If a high light that is larger than a certain size is present on the
screen, remove the high light to see license plates clearly.
HLC OFFHLC ON
HLC MASKING AREA
3. Select a desired mode using the Left and Right buttons and press the SET button.
1. LENS DC
2. EXPOSURE
3. WHITE BAL ATW
4. BACKLIGHT OFF
5. DNR ON
6. DAY/NIGHT AUTO
7. IMAGE ADJ
8. SPECIAL
9. EXIT
MAIN SETUP
■How to Use the Camera
28
29
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera

1. LENS DC
2. EXPOSURE
3. WHITE BAL ATW
4. BACKLIGHT OFF
5. DNR ON
6. DAY/NIGHT AUTO
7. IMAGE ADJ
8. SPECIAL
9. EXIT
MAIN SETUP
3. Set the DNR mode to ‘ON’and press the SET button. Then you can adjust
the noise reduction level.
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’by using
the Up and Down buttons so that the arrow indicates DAY/NIGHT.
■How to Use the Camera
2. Select a desired mode using the Left and Right buttons according to
the picture display you want.
● COLOR : The picture is always displayed in color.
● B/W : The picture is always displayed in black and white.
● AUTO : The mode is switched to Color in a normal environment,
but switches to B/W mode when ambient illumination is low.
To set up the sswitching time or speed for AUTO mode,
press the SET button.
Note
• When using a Video Auto Iris Lens, if you set the lens level to low,
automatic switching between Color and Black & White may not occur.
• Youcannot controltheDAY/NIGHTmenu whenAGC inthe EXPOSURE
menu is ‘OFF’.
At this time, the exchange between DAY mode and NIGHT mode
operates as like selecting ‘COLOR’mode.
• The OSD key does not work for 3 seconds when switching to Color
or B/W, to ensure stable camera operation.
• The cameramayfocuslesswellunderinfraredilluminationthanunder
normal illumination.
• Since the camera may not focus as well under infrared illumination
at night as it does under normal illumination, install an Extra-low
Dispersion Lens to obtain sharp pictures.
Note
• You cannot set the DNR to ‘ON’or ‘OFF’when the AGC mode of the
EXPOSURE menu is ‘OFF’.
• When adjusting the noise reduction level of the DNR mode, remember
that the higher the level set, the more the noise level will be reduced
but that after image may also occur.
DAY/NIGHT
● EXTERN:Thismodeallowsyoutoapplyadesiredfiltertoexternalsignals.
30
31
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera

1. LENS DC
2. EXPOSURE
3. WHITE BAL ATW
4. BACKLIGHT OFF
5. DNR ON
6. DAY/NIGHT AUTO
7. IMAGE ADJ
8. SPECIAL
9. EXIT
MAIN SETUP
1. When the SETUP menu screen is displayed, select ‘IMAGE ADJ.’by using
the Up and Down buttons so that the arrow indicates IMAGE ADJ.
2. Select a desired mode using the Up and Down buttons.
● FREEZE : You can view still or moving pictures.
● V-REV : You can flip the picture vertically on the screen.
● H-REV : You can flip the picture horizontally on the screen.
■How to Use the Camera
● D-ZOOM : You can use a digital zoom of x1~x10.
● SHARPNESS : Asyouincrease thisvalue, thepicture outlinebecomes
stronger and clearer. Adjust this value appropriately
depending on the sharpness of the picture.
Note
• When H-REV or V-REV is selected, any text in the picture also will
be flipped horizontally or vertically.
• If you increase the SHARPNESS level too high, the picture may
become distorted or noise may appear.
IMAGE ADJ.
● RETURN : Select this to save the settings for the IMAGE ADJ. menu
and to return to the SETUPmenu.
IMAGE SETUP
1. FREEZE OFF
2. V-REV OFF
3. H-REV OFF
4. D-ZOOM OFF
5. SHARPNESS ON
6. RETURN
32
33
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera

1. LENS DC
2. EXPOSURE
3. WHITE BAL ATW
4. BACKLIGHT OFF
5. DNR ON
6. DAY/NIGHT AUTO
7. IMAGE ADJ
8. SPECIAL
9. EXIT
MAIN SETUP
1. When the SETUP menu screen is displayed, select ‘SPECIAL’by using the
Up and Down buttons so that the arrow indicates ‘SPECIAL’.
2. Select a desired mode using the Up and Down buttons.
● CAM TITLE : If you enter a title, the title will appear on the monitor.
① IftheSPECIALmenuscreenisdisplayed,usetheUpandDownbuttons
so that the arrow indicates ‘CAM TITLE’.
■How to Use the Camera
② Set it to ‘ON’by using the Left and Right buttons.
③ Press the SET button.
④ Use the 4 direction buttons to move to a desired letter and select
the letter by pressing the SET button. Repeat this to enter multiple
letters. You can enter up to 15 letters.
Note
• If you move the cursor to CLR and press the SET button, all the letters
are deleted. To edit a letter, change the cursor to the bottom left arrow
and press the SET button. Move the cursor over the letter to be edited,
movethecursortothelettertobeinsertedandthenpresstheSETbutton.
Note
• When the CAM TITLE menu is
‘OFF’, no title will be displayed
on the monitor screen even if you
enter one.
SPECIAL
SPECIAL
1. CAM TITLE OFF
2. SYNC INT
3. MOTION DET OFF
4. PRIVACY OFF
5. DIS OFF
6. COMM ADJ
7. LANGUAGE ENGLISH
8. RESET
9. RETURN
SPECIAL
1. CAM TITLE OFF
2. SYNC INT
3. MOTION DET OFF
4. PRIVACY OFF
5. DIS OFF
6. COMM ADJ
7. LANGUAGE ENGLISH
8. RESET
9. RETURN
Camera ID M
LK
JIH
GF
ED
CBA Z
YXW
VU
TSR
QPO
Nmlkjihgfedcba z
yx
wvu
ts
rq
pon 987
6543
2
1
.-
D
NES
OP
RLC→ ←
34
35
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera

⑤ Enter a title, move the cursor to ’POS’and press the SET button. The
entered title appears on the screen. Select the position to display the title
on the screen by using the 4 direction buttons and press the SET button.
When the position is determined, select ’END’and press the SETbutton
to return to the SPECIALmenu.
● SYNC : In areas where the supply is at 60Hz,
you can synchronize the output phase
of multiple cameras using the power
synchronization function (Line-Lock)
without using a synchronization signal
generator.
- INT: Internal Synchronization Type
- L/L: Power Synchronization Type, Line-lock
• Press the SETbutton.
• You can select a desired phase between 0 and 359.
● MOTION DET:
If you connect an alarm device to this camera,
you can monitor activity more efficiently, because
a signal is generated by the camera whenever
motion is detected. The motion detection signal
is output through the MD OUT port.
■How to Use the Camera
① When the SPECIALmenu screen is displayed, press the Up and
Down buttons so that the arrow indicates MOTION DET .
② Set up the mode using the 4 direction buttons.
- SENSITIVITY:Youcanselectupto8MDareas.WhenSENSITIVITY
numberishigh,motiondetectionsensitivityisincreasedtorecognize
even small movement.
- AREAMODE:DetermineswhethertousetheMDareaselected
in SENSITIVITY.
- SELPOS : Determines which of the 4 vertices of each MD area
is to be used.
- YPOS:DeterminesthecoordinateoftheverticalaxisforSELPOS.
- XPOS:DeterminesthecoordinateofthehorizontalaxisforSELPOS.
- FILL→SET : Fills in a selected MD area. Fills in a selected MD
area.The coloroffillingissequentiallyselectedasbrown,orange,
blue, cyan, yellowish green, yellow and red.
- RETURN : Select this to save the MOTION DET menu settings
and return to the SPECIAL menu.
● PRIVACY : Hide an area you want to hide
on the screen.
① When the SPECIALmenu screen is
displayed, press theUpandDownbuttons
so that the arrow indicates ‘PRIVACY’.
Note
• MD areas show only MOTION DETmenu. Therefore, MD areas don’t
display on the monitor screen.
Note
• When using AC power at 60Hz frequency, you can use the L/Ltype
synchronization.
• When the power is DC 12V, the SYNC. menu is fixed to the ‘INT’mode.
① Setupthemodeusingthe4directionbuttons.
-AREASEL:Youcanselectupto8areas.
-AREAMODE:
Determineswhethertousethe areaselected
intheAREASEL,andthe sizeand positionof
thearea.
36
37
Super DNR High Resolution Day/Night Camera Super DNR High Resolution Day/Night Camera