Blancett B170180 User manual

SEN-UM-02442-EN-01 (July 2017) Installation Data

Pickups for B1750 Meter

B170180 Quad-4 Hall Eect Sensor

DESCRIPTION

The B170180 Quad-4 Hall Effect Pickup is a microprocessor-based

sensor for use with the B1750 positive displacement flow meters.

The Quad-4 sensor can detect both uni- and bi-directional flow. The

sensor’s mode of operation is determined by an output selection

switch inside the housing. The Quad-4 sensor detects the rotation of

the flow meter gears and emits a frequency signal proportional to

flow. The output signal is a square wave pulse that has a duty cycle

of approximately 50%.

The Quad-4 signal outputs are protected with a self-resetting fuse.

This fuse has a 50 mA nominal trip point. When a trip occurs, turn off

power to the sensor and remove the output load to reset the fuse.

The sensor has a sourcing output configuration when jumpers JP1

and JP2 are shorting pins.

The Quad-4 sensor circuit board has a red and green LED. The red

LED is a status LED which, when the sensor is operating properly,

flashes once every 4 seconds. A fast flash indicates a failure of one or

more of the pickups. The green LED indicates the pulse of the input

signal. Signals above 20 Hz are solid green.

INSTALLATION

1. Make sure that the ow meter sensor cavity is free of debris prior

to installing the pickup.

2. Install the ow meter and sensor.

3. Cycle the power so the sensor functions properly.

Securing the Sensor to the Flow Meter

Use a 9/64 hex key to tighten internal screws.

1.38 in.

To secure the sensor to the ow meter,

use a 9/64 hex key to tighten the

internal screws.

Figure 1: Securing the sensor to the flow meter

Test Feature

The Quad-4 pickup is equipped with an output test feature for

readouts before the initial running of your system.

OTE:N Power must be cycled for new setting to take effect.

• Switch setting 8 causes the pickup to output a 10 Hz (+/- 20%)

Phase = +90° pulse output, simulating low flow conditions

without flow through the meter

• For sourcing outputs, place the shorting block across JP1 & JP2

(factory default)

• Switch setting 9 causes the pickup to output a 250 Hz

(+/- 20%) Phase = -90° pulse output, simulating medium flow

conditions without flow through the meter.

Electrical Connection for Pin Connector

Pin Number Function

1 NC

2 Output 2

3 NC

4 Output 1

5 Ground

6 Supply

Wiring Color Code

Pin Number Wire Color

Signal 2 2 Green

Signal 1 4 White

Ground 5 Black

Supply Voltage 6 Red

Quad-4 Operating Modes

Switch Output 1 Output 2

0 Flow Direction Signal 2

1 1 × frequency +90° phase

2 Flow Direction 2 × frequency

3 2 × frequency +90° phase

4 Flow Direction 4 × frequency

5 Both outputs 4 × frequency in phase

6 Reserved

7 Foward pulses Reverse pulses

8 Test: S1 & S2 == 10 Hz (± 20%) Phase = +90°

9 Test: S1 & S2 == 250 Hz (± 20%) Phase = -90°

RED LED

GREEN LED

JP1

SWITCH JP2

Figure 2: Pinout looking at male

connector on sensor

Figure 3: Top view of circuit board

with vew of LEDs and switch

Pickups for B1750 Meter, B170180 Quad-4 Hall Eect Sensor

www.badgermeter.com

BLANCETT is a registered trademark of Badger Meter, Inc. Other trademarks appearing in this document are the property of their respective entities. Due to continuous research,

product improvements and enhancements, Badger Meter reserves the right to change product or system specications without notice, except to the extent an outstanding