Blaupunkt Radio Professional User manual

Operating and installation instructions
Bedienungs- und Einbauanleitung
Mode d'emploi et de montage
Instruções de serviço e de montagem
Instrucciones de manejo e instalación
Istruzioni d'uso e di installazione
Gebruiksaanwijzing en inbouwhandleiding
Betjenings- og monteringsvejledning
Bruks- och monteringsanvisning
Käyttö- ja asennusohje
Instrukcja obsługi i montażowa
Kezelési és beszerelési útmutató
Инструкция по эксплуатации и монтажу
Návod kobsluze akmontáži
Návod na obsluhu ainštaláciu
Car Radio
|
CD
|
USB
|
SD
|
Bluetooth
Blaupunkt Radio Professional
Blaupunkt Radio Basic

2
Controls
1 SRC button
Select memory bank or audio source
2 On/O button
Short press: Switch on car sound system
In operation: Mute car sound system
Long press: Switch o car sound system
3 Infrared receiver
4 Volume control
In the menu: Change settings
Fast-Browse mode: Select folder and track
5 CD tray (Professional only)
6 Display
7 / button
In the menu: Select menu item
Radio mode: Start seek tuning
MP3/WMA mode: Change to next/previous
folder
/ button
In the menu: Change menu level
Radio mode: Adjust the stations
Other operating modes: Track selection
8 button (Eject) (Professional only)
Eject a CD
9 USB socket
: Front AUX-IN socket
; Keys 1 - 3 (Professional)
Keys 1 - 6 (Basic)
< MENU button
Short press: Call up/close menu
Long press: Start scan function
= button (Professional only)
• If no connection to a Bluetooth® device
exists, activate the pairing mode. The
display shows the currently stored PIN
(default "1234").
• If a connection to a Bluetooth® device
currently exists
Short press: Answer a call, speed dial
Long press: Activate voice dial
> button (Professional only)
Ending/rejecting a phone call
? SD card slot
Professional
Basic
2 75 6
10 915 1214 13 11
1 83 4
2 76
10 915 11
1123 4

3
ENGLISH
Contents
Safety notes ...................................................... 4
Symbols used.............................................................. 4
Road safety .................................................................. 4
General safety notes................................................. 4
Declaration of conformity......................................4
Cleaning notes.................................................. 5
Disposal notes................................................... 5
Scope of delivery .............................................. 5
Optional equipment ........................................ 5
Placing the device in operation....................... 5
Code protection......................................................... 5
Setting the reception area ..................................... 6
Switching on/o ........................................................ 6
Volume .......................................................................... 6
Switching demo mode on/o............................... 6
Trac information............................................ 6
Radio mode....................................................... 7
RDS.................................................................................. 7
Changing to radio mode or selecting
a memory bank .......................................................... 7
Tuning into a station ................................................7
Storing stations or calling stored stations........ 8
Scanning stations ...................................................... 8
Storing stations automatically (Travelstore).... 8
PTY.................................................................................. 9
CD/MP3/WMA mode......................................... 9
Basic information....................................................... 9
Changing to CD/MP3/WMA mode....................10
Inserting/ejecting a CD (Professional only)....10
Connecting/removing a USB data carrier.......11
Inserting/removing a memory card .................11
Selecting tracks ........................................................11
Selecting a folder (only in MP3/WMA mode)...11
Fast searching ...........................................................11
Interrupting playback (Basic only) ....................11
Scanning all tracks ..................................................11
Playing tracks in random order ..........................12
Repeatedly playing individual tracks or
directories ..................................................................12
Browse mode ............................................................12
Bluetooth® (Professional only)...................... 13
The Bluetooth® menu ............................................13
Pairing and connecting a Bluetooth®
device...........................................................................13
Telephone functions...............................................14
Bluetooth® streaming mode................................16
Additional functions in the Bluetooth®
menu............................................................................16
External audio sources................................... 17
Front AUX-IN socket................................................17
Sound settings................................................ 17
Calling and exiting the "AUDIO" menu............17
Making settings in the "AUDIO" menu.............18
User settings ................................................... 18
Calling the user menu and selecting
a menu.........................................................................18
Making settings in the "TUNER" menu............19
Making settings in the "DISPLAY" menu .........20
Making settings in the "VOLUME" menu ........20
Making settings in the "VARIOUS" menu........21
Factory settings .............................................. 21
Useful information ......................................... 22
Warranty .....................................................................22
Service .........................................................................22
Software update ......................................................22
Technical data................................................. 22
Installation instructions .............................. 346
Supplied mounting hardware..........................354
Optional equipment............................................ 355
Installation instructions...................................... 356
Removal ................................................................... 357
Pin assignment...................................................... 358
Connection diagram ........................................... 359
Microphone connection .................................... 360

4
Safety notes
The car sound system was manufactured accord-
ing to the state of the art and established safety
guidelines. Even so, dangers may occur if you do
not observe the safety notes in these instructions.
• Read these instructions carefully and com-
pletely before using the car sound system.
• Keep the instructions at a location so that they
are always accessible to all users.
• Always pass on the car sound system to third
parties together with these instructions.
In addition, observe the instructions of the devices
used in conjunction with this car sound system.
Symbols used
These instructions employ the following symbols:
DANGER!
Warns about injuries
CAUTION!
Warns about damaging the CD drive
DANGER!
Warns about high volume
The CE mark conrms the compliance
with EU directives.
쏅Identies a sequencing step
• Identies a listing
Road safety
Observe the following notes about road safety:
• Use your device in such a way that you can
always safely control your vehicle. In case of
doubt, stop at a suitable location and operate
your device while the vehicle is standing.
• Always listen at a moderate volume to pro-
tect your hearing and to be able to hear acous-
tic warning signals (e.g. police sirens). During
mute phases (e.g. when changing the audio
source), changing the volume is not audible.
Do not increase the volume during this mute
phase.
General safety notes
Observe the following notes to protect yourself
against injuries:
• Do not modify or open the device. The device
contains a Class 1 laser that can cause injuries
to your eyes (Professional only).
• Do not increase the volume during mute
phases, e.g. when changing the audio source.
Changing the volume is not audible during a
mute phase.
Use as directed
This car sound system is intended for installation
and operation in a vehicle with 12 V vehicle sys-
tem voltage and must be installed in a DIN slot.
Observe the performance limits in the technical
data. Repairs and installation, if necessary, should
be performed by a specialist.
Declaration of conformity
The Blaupunkt Technology GmbH declares that
the car sound system Basic complies with the
basic requirements and the other relevant regu-
lations of the directive 2004/108/EC and the car
sound system Professional complies with the basic
requirements and the other relevant regulations
of the directive 1999/5/EC.
Safety notes

5
ENGLISH
Cleaning notes | Disposal notes | Scope of delivery | Optional equipment | Placing the device in operation
Cleaning notes
Solvents, cleaning and scouring agents as well as
dashboard spray and plastics care product may
contain ingredients that will damage the surface
of the car sound system.
Use only a dry or slightly moistened cloth for
cleaning the car sound system.
Disposal notes
Do not dispose of your old unit in the house-
hold trash!
Use the return and collection systems available to
dispose of the old device.
Scope of delivery
The scope of delivery includes:
1 Car sound system
1 Operating/installation instructions
1 Support frame
2 Disassembly tools
1 Distance bolt (Basic)
1 Guide pin
1 Microphone (Professional)
1 Microphone adapter cable (Professional)
Optional equipment
Not part of the scope of delivery. Use only optional
equipment approved by Blaupunkt, such as:
• Amplier
• Amplier connecting cable
• IR remote control RC12H
Information is available on the Internet under
www.blaupunkt.com or via the Blaupunkt Service
Hotline service-bpeblaupunkt.com.
Placing the device in operation
Code protection
This car sound system is protected against theft
with a four-digit code number. You can specify
that the code number must be entered after every
interruption of the power supply from the vehicle
battery. With activated code query and without
this code number, the car sound system is useless
to a thief.
Notes:
• The code query is set to inactive at the
factory, but it can be activated (see the
chapter "User settings", section "Making
settings in the "VARIOUS" menu", menu
item "SEC CODE").
• The default setting of the code number is
"0000". The code number can be changed
(see the chapter "User settings", section
"Making settings in the "VARIOUS" menu",
menu item "CODE SET").
Entering the code number after a voltage
interruption
If the code query is activated, the four-digit code
number must be re-entered every time the device
is disconnected from the vehicle system voltage
(e.g. removal of the battery for repairs).
For each digit of the code number:
쏅Press the / button
7 to set the current
digit.
쏅Press the button
7 to conrm.
Note:
When entering the code, you may return to a
previous digit by pressing the button
7 .
After setting and conrming the fourth digit, the
car sound system is switched on.
Note:
If you enter an incorrect code number, "CODE
ERR" is briey displayed and the device is
blocked for 99 seconds. Afterwards you can
retry the entry.

6
Placing the device in operation | Trac information
Setting the reception area
This car sound system is designed for operation in
dierent regions with dierent frequency ranges
and station technologies. The factory default of
the reception area is "EUROPE". In addition, the re-
ception areas "USA", "S-AMERICA" and "THAILAND"
are available.
Note:
If you operate the car sound system outside of
Europe, you may rst have to set a suitable re-
ception area in the user menu (see the chap-
ter "User settings", section "Making settings in
the "TUNER" menu", menu item "AREA").
Switching on/o
Switching on/o with the On/O button
쏅For switch-on, press the On/O button
2 .
The car sound system switches on.
쏅To switch o the device, press and hold down
the On/O button
2 for longer than 2 sec-
onds.
The car sound system switches o.
Note:
If you switch on the car sound system while
the vehicle ignition is switched o, it auto-
matically switches o after 1 hour to preserve
the vehicle battery.
Switching on/o via vehicle ignition
The car sound system will switch o/on simulta-
neously with the ignition if the device is correctly
connected to the vehicle’s ignition as shown in the
installation instructions and you did not switch
the device o by pressing the On/O button 2 .
Volume
Adjusting the volume
You can adjust the volume in steps from 0 (o) to
50 (maximum).
쏅Turn the volume control
4 to change the
volume.
Muting the car sound system (Mute)
쏅Briey press the On/O button
2 to mute
the car sound system or to reactivate the pre-
vious volume.
During muting, the display shows "MUTE".
Switching demo mode on/o
The demo mode shows the functions of the car
sound system as scrolling text on the display. You
can turn the demo mode on or o:
쏅Switch o the car sound system if it is not
already turned o.
Basic
쏅Press and hold the buttons
7 and 1 LIST
; at the same time and press the On/O
button
2 .
Professional
쏅Press and hold the buttons
7 and >
at the same time and press the On/O but-
ton 2 .
The car sound system switches on.The display
briey shows "DEMO MODE" if you switched
on the demo mode. By pressing any button,
the demo mode is interrupted and you can
operate the device.
Trac information
In the reception area "EUROPE", an FM station can
identify trac reports by means of an RDS signal.
If priority for trac reports is switched on, a traf-
c report is automatically switched through, even
if the car sound system is currently not in radio
mode.
If priority is switched on, the display shows the
trac jam symbol ( ). "TRAFFIC" is displayed
during a switched-through trac announcement.
The priority is activated and deactivated in the
user menu (see the chapter "User settings", sec-
tion "Making settings in the "TUNER" menu", menu
item "TRAFFIC").

7
ENGLISH
Trac information | Radio mode
Notes:
• The volume is increased for the duration
of the switched-through trac announce-
ment.You can adjust the minimum volume
for trac announcements (see the chapter
"User settings", section "Making settings
in the "VOLUME" menu", menu item "TA
VOLUME").
• To cancel a switched-through trac an-
nouncement, press the SRC button
1 .
Radio mode
RDS
Many FM stations broadcast an RDS (Radio Data
System) signal in addition to their programme
in the reception area "EUROPE" that allows the
following additional functions:
• The station name is shown on the display.
• The car sound system recognises trac an-
nouncements and news broadcasts and can
automatically switch them through in other
operating modes (e.g. in CD mode).
• Alternate frequency: If RDS is activated, the car
sound system automatically selects the best
receivable frequency for the station that is cur-
rently set.
• Regional: At certain times, some radio sta-
tions divide their programme into regional
programmes providing dierent content. If
the REGIONAL function is activated, the car
sound system changes only to those alternate
frequencies on which the same regional pro-
gramme is being broadcast.
The functions RDS and REGIONAL are activated
and deactivated in the user menu (see the chap-
ter "User settings", section "Making settings
in the "TUNER" menu", menu items "RDS" and
"REGIONAL").
Changing to radio mode or selecting
a memory bank
The following memory banks are available in the
dierent reception areas:
Region Memory banks
EUROPE FM1, FM2, FMT, MW, LW, SW
USA FM1, FM2, FMT, AM, AMT, SW
S-AMERICA FM1, FM2, FMT, AM, AMT, SW
THAILAND FM1, FM2, FMT, AM, AMT, SW
쏅Press the SRC button
1 repeatedly until the
desired memory bank is displayed.
Notes:
• Up to 3 stations (Professional) or up to
6 stations (Basic) can be stored in each
memory bank.
• Memory banks can be activated or deacti-
vated via the user menu (see the chapter
"User settings", section "Making settings
in the "TUNER" menu", menu item "TUN
BAND" (band selection)). Deactivated
memory banks are skipped during the
source selection with the SRC button 1 .
Tuning into a station
There are various ways of tuning into a station:
Tuning into stations manually
쏅Briey press the / button 7 once or
several times to change the frequency in in-
crements, or long to quickly change the fre-
quency.
Note:
For the reception areas "EUROPE" and "USA":
In the FM waveband, the current selected
programme type is displayed and can be
changed if the PTY function is activated (see
the chapter "PTY").

8
Radio mode
Starting station seek tuning
쏅Press the / button
7 to start station
seek tuning.
The radio tunes into the next receivable
station.
Notes:
• For the reception area "EUROPE": In the FM
waveband, only trac information stations
are tuned into if the priority for trac infor-
mation ( ) is switched on.
• For the reception areas "EUROPE" and
"USA": In the FM waveband, the next
station with the currently selected pro-
gramme type is tuned into if the PTY func-
tion is activated (see the chapter "PTY").
• The sensitivity of seek tuning can be ad-
justed (see the chapter "User settings",
section "Making settings in the "TUNER"
menu", menu item "SEEK SENS").
Storing stations or calling stored
stations
쏅Select the desired memory bank.
쏅If necessary, set the desired station.
쏅Press a station button
; for approx. 2 sec-
onds to store the current station under the
button.
- or -
쏅Briey press a station button
; to call up the
stored station.
Scanning stations
The scan function is used to scan every receivable
station of the current waveband.
Note:
You can adjust the scan time for each sta-
tion (see the chapter "User settings", section
"Making settings in the "VARIOUS" menu",
menu item "SCAN TIME").
쏅Press the MENU button
< for approx. 2 sec-
onds to start scanning.
During the scan, the display alternately dis-
plays "SCAN" and the current frequency as
well as memory bank or station name.
쏅Briey press the MENU button
< to con-
tinue listening to the station that is currently
being received.
Storing stations automatically
(Travelstore)
Travelstore allows automatically scanning the
3strongest FM stations of the region (Professional)
or the 6strongest FM stations of the Region (Basic)
and storing them in the FMT memory bank. Any
previously stored stations in this memory bank are
deleted in the process.
In the reception areas "USA", "S-AMERICA" and
"THAILAND", you can also store 3 or 6AM stations
in the AMT memory bank.
쏅Select a memory bank of the desired wave-
band, e.g. FM1 or AM.
쏅Press the SRC button 1 for approx. 2 sec-
onds.
The tuner starts the automatic station seek
tuning; the display shows "FM TSTORE" or
"AM TSTORE". After the storing is completed,
the radio plays the station at memory location
1 of the FMT or AMT level.
Notes:
• For the reception area "EUROPE": If the
priority for trac information is switched
on ( ), only trac information stations
are stored.
• If the FMT or AMT memory bank is deac-
tivated (see the chapter "User settings",
section "Making settings in the "TUNER"
menu", menu item "TUN BAND"), it is au-
tomatically reactivated if you initiate the
Travelstore function.

9
ENGLISH
Radio mode | CD/MP3/WMA mode
PTY
In the reception areas "EUROPE" and "USA", an
FM station can transmit its current programme
type, e.g. CULTURE, POP, JAZZ, ROCK, SPORT or
SCIENCE. Hence, the PTY function allows a target-
ed search for broadcasts of a certain programme
type, e.g. for rock or sports broadcasts. Note that
PTY is not supported by all stations.
Note:
The PTY function is only available if it has been
activated (see the chapter "User settings", sec-
tion "Making settings in the "TUNER" menu",
menu item "PTY").
Selecting a programme type
쏅Briey press the / button
7 .
The currently selected programme type is
briey displayed, and you can select a dier-
ent programme type.
쏅If necessary, press the / button
7 re-
peatedly until the desired programme type
is selected.
Note:
In the reception area "EUROPE", you can ad-
just the language in which the programme
types are displayed (see the chapter "User
settings", section "Making settings in the
"TUNER" menu", menu item "PTY LANG").
Searching for stations
쏅Press the / button
7 .
During the seek tuning, the currently selected
programme type is shown on the display.
As soon as a station with the desired pro-
gramme type is found, it remains being tuned
into.
Notes:
• If no station with the selected programme
type is found, "PTY NONE" is briey dis-
played and 1 beep can be heard. The radio
will then retune to the station that it played
last.
• If the tuned radio station or another sta-
tion on the broadcasting network broad-
casts your selected programme type at a
later point in time, the car sound system
will automatically switch from the cur-
rently tuned station to the station whose
programme type matches the one you
selected. Note that this function is not sup-
ported by all stations.
CD/MP3/WMA mode
Basic information
Professional:
This car sound system can be used to play audio
CDs (CDDA) and CD-R/RWs with audio, MP3 or
WMA les as well as MP3 orWMA les on USB data
carriers and SD(HC)/MMC cards.
Basic:
This car sound system can be used to play MP3 or
WMA les on USB data carriers and SD(HC)/MMC
cards.
Notes:
• To ensure proper functioning, use only CDs
with the Compact-Disc logo.
• Blaupunkt cannot guarantee the awless
function of copy-protected CDs and all
CD blanks, USB data carriers and memory
cards available on the market.
Note the following information when preparing
an MP3/WMA data carrier:
• Naming of tracks and directories:
– Max. 32 characters without the le exten-
sion ".mp3" or ".wma" (the use of more
characters reduces the number of tracks
and folders that the car sound system can
recognise)
– No umlauts or special characters
• CD formats: CD-R/RW, Ø: 12 cm
• CD data formats: ISO 9669 Level 1 and 2, Joliet
• CD burn speed: Max. 16x (recommended)
• USB format/le system: Mass storage device /
FAT16/32

10
• Memory card le system: FAT16/32
• File extension of audio les:
– .MP3 for MP3 les
– .WMA for WMA les
•WMAles only without Digital Rights Manage-
ment (DRM) and created with Windows Media
Player version 8 or later
• MP3 ID3 tags: Version 1 and 2
• Bitrate for creating audio les:
– MP3: 32 to 320 kbps
– WMA: 32 to 192 kbps
• Maximum number of les and directories:
– USB medium: Up to 20,000 entries de-
pending on the data structure
– Memory cards: Up to 1,500 les (directories
and tracks) per directory
Changing to CD/MP3/WMA mode
쏅Press the SRC button 1 repeatedly until the
desired audio source is displayed:
• "CD": Inserted CD (Professional only)
• "SD(HC)": Inserted memory card
• "USB": Connected USB data carrier
• "AUX": Connected external audio source
Notes:
• The respective audio source can be se-
lected only if a corresponding data carrier
is inserted or a corresponding device is
connected.
• If the car sound system rst has to read
the data of a connected device or data car-
rier before the playback, the display shows
"READING". The duration of the reading
depends on the data volume and design of
the device or data carrier. If the device or
data carrier is defective or the transferred
data cannot be played back, a correspond-
ing message appears on the display (e.g.
"USB ERROR").
Inserting/ejecting a CD
(Professional only)
Inserting a CD
Risk of severe damage to the CD
drive!
Noncircular contoured CDs (shape CDs)
and CDs with a diameter of 8 cm (mini CDs) must
not be used.
We accept no responsibility for any damage to the
CD drive that may occur as a result of the use of
unsuitable CDs.
Note:
You must not hinder or assist the drive as it
automatically draws in the CD.
쏅Insert the CD with its printed side up into the
CD tray
5 until you feel a slight resistance.
The drive automatically draws in the CD and
checks its data. Afterwards, the playback
starts in CD or MP3 mode.
Note:
If the inserted CD cannot be played back, "CD
ERROR" is briey displayed and the CD is au-
tomatically ejected after approx. 2 seconds.
Ejecting a CD
Note:
You must not hinder or assist the drive as it
ejects the CD.
쏅Press the button
8 to eject an inserted
CD.
Notes:
• If a CD is ejected and not removed, the
drive will automatically draw it back in
again after approx. 10 seconds.
• You can also eject CDs while the car sound
system is switched o or whilst another au-
dio source is activated.
CD/MP3/WMA mode

11
ENGLISH
Connecting/removing a USB data
carrier
Connecting a USB data carrier
쏅Switch o the car sound system so that the
data carrier will be correctly registered.
쏅Pull the protective cap of the USB socket
9
to the front until it moves out of the socket
and fold it down.
쏅Connect the USB data carrier.
쏅Turn on the car sound system.
If the USB data carrier is initially selected as
audio source, the data are read rst.
Notes:
• If the connected USB data carrier cannot
be seen, "USB ERROR" is briey displayed.
• The time required for reading in the data
depends on the design and size of the USB
data carrier.
Removing a USB data carrier
쏅Switch o the car sound system so that the
data carrier will be correctly unregistered.
쏅Disconnect the USB data carrier.
쏅Close the protective cap of the USB socket
9 .
Inserting/removing a memory card
Inserting a memory card
쏅Switch o the car sound system so that the
memory card will be correctly registered.
쏅Open the cover of the card slot ? .
쏅Insert the memory card with its labelled side
up and its contacts rst into the card slot
?
until it clicks into place.
쏅Close the cover of the slot again.
쏅Turn on the car sound system.
Notes:
• If the inserted memory card cannot be
played, "SD ERROR" is briey displayed.
• The time required for reading in the data
depends on the design and size of the
memory card.
Removing the memory card
쏅Switch o the car sound system so that the
memory card will be correctly unregistered.
쏅Open the cover of the card slot
? .
쏅Push on the memory card until it disengages.
쏅Pull the memory card out of the card slot.
쏅Close the cover of the slot again.
Selecting tracks
쏅Press the / button 7 briey to change
to the previous/next track.
Note:
If the current track plays longer than 3 sec-
onds, pressing
7 once restarts the track.
Selecting a folder
(only in MP3/WMA mode)
쏅Press the / button 7 briey to change
to the previous/next folder.
Fast searching
쏅Press and hold down the button / 7
until the desired position has been reached.
Interrupting playback
(Basic only)
쏅Press the 3 ; button to interrupt the
playback ("PAUSE") or to continue it.
Scanning all tracks
The scan function scans all available tracks.
쏅Press the MENU button
< for approx. 2 sec-
onds to start the scan, or briey to continue
playing the currently scanned track.
During the scan, the display alternately dis-
plays "PLAY SCAN" and the playing time of
the current track.
Note:
The scan time can be adjusted (see the chap-
ter "User settings", section "Making settings
in the "VARIOUS" menu", menu item "SCAN
TIME").
CD/MP3/WMA mode

12
Playing tracks in random order
쏅Press the MIX button ; to change among
the playback modes:
Operation Display Meaning
CD* MIX ALL Mixing tracks
MP3/
WMA
MIX DIR Mixing tracks of
the current folder
MIX ALL Mixing tracks of
the data carrier
Gen. MIX OFF Regular playback
* Professional only
If the MIX function is switched on, the icon
MIX (mix all tracks) or MIX (mix tracks of
current folder) is shown on the display.
Repeatedly playing individual tracks
or directories
쏅Press the RPT button ; to change among
the playback modes:
Operation Display Meaning
CD* RPT TRACK Repeating tracks
MP3/
WMA
RPT TRACK Repeating tracks
RPT DIR Repeating
folders
Gen. RPT OFF Regular playback
* Professional only
If the RPT function is switched on, the icon
(repeat tracks) or (repeat
folders) is shown on the display.
Browse mode
In Browse mode, you can directly search for and
select a certain track on the MP3/WMA data carrier
without interrupting the current playback.
Calling the browse mode
쏅Press the 1 LIST button ; to call up the
browse mode.
The icon ashes on the display. In ad-
dition, the icon (folder) or icon (track)
appears. The rst or current folder on the data
carrier is being displayed.
Notes:
• The rst folder is displayed only if the
browse mode has been called for the rst
time after inserting or connecting the data
carrier. Afterwards, the current folder is
displayed whenever the browse mode is
called.
• You can exit the browse mode at any time
by pressing the 1 LIST button
; .
쏅Press the / button
7 once or several
times to select a dierent folder.
쏅Press the button
7 to display the tracks of
the selected folder.
The rst track of the folder is shown on the
display.
Note:
Pressing the button 7 returns you to the
folder list.
쏅Press the / button
7 once or several
times to select a dierent track.
쏅Press the button
7 to play the track.
The playback starts. You are exiting the
browse mode.
Fast browsing
Fast browsing enables faster access to tracks. In-
stead of the arrow keys
7 , you use the volume
control 4 to select list entries:
Function Browse
mode
Fast browse
mode
Selecting
entries in lists /
7
Volume
control 4
Conrming
entries
7 7
Return to the
higher level
7 7
CD/MP3/WMA mode

13
ENGLISH
Fast browsing is switched on or o in the user
menu (see the chapter "User settings", section
"Making settings in the "VARIOUS" menu", menu
item "BROWSE").
Note:
With activated fast browsing, you cannot
change the volume in browse mode. To do
so, rst exit the browse mode by pressing
the button 1 LIST
; or starting the track
playback.
Bluetooth®
(Professional only)
You can connect the car sound system via Blue-
tooth® with other Bluetooth®-ready devices, such
as cell phones or MP3 players. This allows you to
use the car sound system with its microphone as
hands-free system for connected cell phones and
control the audio output of other Bluetooth® de-
vices and play them back via the loudspeakers of
the car sound system (Bluetooth® streaming).
Bluetooth® technology is a wireless connection of
short range. For this reason, Bluetooth® devices
must be located near the car sound system (in the
vehicle) to establish and maintain a connection.
To establish a Bluetooth® connection, you must
rst pair the car sound system and the Bluetooth®
device. When you pair the devices, a Bluetooth®
connection is subsequently established automati-
cally. This connection remains in eect as long as
the Bluetooth® device is within range. If the con-
nection is interrupted, e.g. because you moved
the cell phone outside the range, the connection
is automatically re-established as soon as you are
back within range.
You can connect only one cell phone and stream-
ing device with the car sound system at a time.
If you connect a new device with the car sound
system, the connection to a currently connected
device may automatically be interrupted. How-
ever, the car sound system leaves up to 5 dierent
Bluetooth® devices paired, and you can quickly
and easily connect any of these devices with the
car sound system again.
The Bluetooth® menu
In the Bluetooth® menu, you nd all the functions
for pairing, connecting and managing Bluetooth®
devices.
Calling the Bluetooth® menu
쏅Briey press the MENU button
< to open
the user menu.
쏅Press the / button
7 repeatedly until
the "BLUETOOTH" menu item is selected.
쏅Press the button
7 to open the Blue-
tooth® menu.
쏅Press the / button
7 repeatedly until
the desired menu item is selected.
쏅Perform the setting (see the following sec-
tions).
쏅Briey press the MENU button
< to exit the
menu.
Notes:
• The Bluetooth® menu is automatically ex-
ited approx. 30 seconds after the last but-
ton activation and you are returned to the
display of the current audio source.
• In the menu, you can press the button
7 in each case to return to the higher
menu level.
Pairing and connecting a Bluetooth®
device
Notes:
• You can pair up to 5 Bluetooth® devices
with this car sound system. If you register a
sixth one, the Bluetooth® device registered
rst is deleted.
• If a connection with a Bluetooth® device
currently exists, this connection is auto-
matically disconnected if you pair and
connect another device.
If a connection to a Bluetooth® device exists,
쏅select the "PAIRING" menu item in the
Bluetooth® menu and press the button
7 .
쏅Press the button
7 again to activate the
pairing mode.
CD/MP3/WMA mode | Bluetooth®

14
Bluetooth®
If no connection to a Bluetooth® device exists,
쏅press the button = to activate the pair-
ing mode.
The display shows "PAIRING" the currently
stored PIN (default "1234"). In addition, the
Bluetooth® icon ashes. The car sound sys-
tem can now be recognised by a Bluetooth®
device for approx. 2minutes and connected.
쏅Select the car sound system (Bluetooth®
name: "BP PROFESSIONAL") from the device
list of your Bluetooth® device to establish the
connection.
쏅If necessary, enter the PIN displayed by the car
sound system at the Bluetooth® device.
The display may briey show "PAIRED", fol-
lowed by "CONNECTED", as soon as the car
sound system and the Bluetooth® device have
been paired and connected.
Notes:
• If no connection can be established, the
display briey shows "CONNECT FAILED".
• If no connection can be established to the
previously connected Bluetooth® device
after switching on the car sound system,
the display briey shows "NO DEVICE".
• After switching on, the car sound system
automatically attempts to reconnect the
previously connected Bluetooth® device.
During this time, the Bluetooth® icon
ashes.
Telephone functions
Answering/rejecting an incoming phone call
With an incoming call, the display alternately
shows "IN CALL" and the number of the caller. The
current audio source is muted and a ring tone is
played via the loudspeakers of the car sound sys-
tem.
Note:
If the number of the caller is not being trans-
mitted, the display shows "IN CALL" instead
of the number. If the number of the caller is
stored together with a name in the car sound
system, the name of the entry and the num-
ber are displayed (see the section "Storing a
phone number in the car sound system" in
this chapter).
쏅Press the button
= to answer the call.
"CALL" and the duration of the ongoing call
are displayed.
쏅Press the button > to reject the call or
to end the current call.
The display shows "END CALL".
Notes:
• During the call, you can adjust the volume
with the volume control
4 or mute the
microphone and the loudspeakers with a
short press of the On/O button 2 .
• You can preset the minimum volume for
the call playback in the user menu (see
the chapter "User settings", section "Mak-
ing settings in the "VOLUME" menu", menu
item "TEL VOL").
Making a call
쏅In the Bluetooth® menu, select the "DIAL NEW
NUMBER" menu item.
쏅Press the button
7 to open the entry
menu.
You can now enter a phone number with up
to 20 digits:
쏅Turn the volume control
4 to select a digit
for the respective position.
쏅Press the or button
7 to reach the next
or previous position.
Notes:
• You can also reach the next position by
pressing the ON/O button
2 .
• While entering the phone number, you
cannot change the volume or mute the car
sound system.
쏅Press the button
= to call the number
entered.
"CALLING" and the dialed number are alter-
nately shown on the display.

15
ENGLISH
Bluetooth®
As soon as your calling party answers the call,
the display shows "CALL" and the time of the
current phone call.
Upon ending the call, the display briey
shows "END CALL".
Making a call with voice dial
Note:
This function is only available if the connected
cell phone supports voice dial.
쏅In the Bluetooth® menu, select the "VOICE
DIAL" menu item.
쏅Press the button
7 to activate voice rec-
ognition.
- or -
쏅Press the button
= for approx. 2 sec-
onds to activate the voice recognition with
the speed dial.
The car sound system is muted and the dis-
play shows "SPEAK NOW".
쏅Say the name of the desired calling partner.
Notes:
• If no Bluetooth® connection is established
when voice recognition is activated, the
display briey shows "VOICE DIAL FAILED".
• If the spoken name is not being recognised
or the time for the voice recognition has
already expired, the display briey shows
"VOICE DIAL FAILED".
• You can cancel the voice recognition by
pressing the button
> .
• Please note that the duration of the voice
recognition is limited and depending on
the respective cell phone.
Storing a phone number in the car sound
system
You can store three phone numbers in the car
sound system and place calls with the speed dial
(see the following section).
쏅Enter the phone number as described in the
section "Making a call".
쏅Press the desired memory button 1 - 3
; for
approx. 2 seconds to store the number.
You can now enter a name with up to 15 char-
acters:
쏅Turn the volume control 4 to select a char-
acter for the respective position.
쏅Press the or button
7 to reach the next
or previous position.
Note:
You can also reach the next position by press-
ing the ON/O button
2 .
쏅Press the memory button 1 - 3
; again for
approx. 2 seconds to store the number and
name.
The display briey shows "NUMBER SAVED".
Afterwards, you are returned to the Blue-
tooth® menu and the "DIAL NEW NUMBER"
menu item.
Note:
A number previously stored on the memory
button is replaced.
Speed dial for any phone number or for the
number dialed last or a stored number
With speed dial, you can make a call without rst
having to select the corresponding function in the
Bluetooth® menu.
To call the number dialed last,
쏅press the button
= .
The display shows the number dialed last.
Note:
If no cell phone is currently connected, the
Bluetooth® menu is opened. The "PAIRING"
menu item is selected.
쏅Press the button
= to call the number.
"CALLING" and the dialed number are alter-
nately shown on the display.

16
Bluetooth®
To call a stored number,
쏅press the button = .
쏅Press a memory button 1 - 3
; to call the
stored number.
Note:
If no number is stored under the selected
memory button, the display briey shows
"NO NUMBER".
쏅Press the button
= to call the number.
"CALLING" and the dialed number are alter-
nately shown on the display.
To call any number,
쏅press the button
= .
쏅Press the On/O button
2 to open the entry
menu and enter a number (enter the phone
number as described in the section "Making
a call").
쏅Press the button
= to call the number.
"CALLING" and the dialed number are alter-
nately shown on the display.
Bluetooth® streaming mode
Starting the Bluetooth® streaming mode
쏅Press the SRC button
1 repeatedly until "BT
STREAM" appears on the display.
The playback starts.
Notes:
• The Bluetooth® streaming mode can be
selected only if a suitable streaming device
is connected.
• If the connection to the streaming de-
vice is lost during playback, the display
briey shows "DISCONNECTED" and the
car sound system changes to the previous
audio source.
Selecting tracks
쏅Press the / button
7 briey to change
to the previous/next track.
Additional functions in the
Bluetooth® menu
Changing the Bluetooth® PIN
The factory-set Bluetooth® PIN of the car sound
system is "1234"; e.g. it must be entered on the
cell phone when pairing a cell phone.This PIN can
be changed.
쏅In the Bluetooth® menu, select the "PIN EDIT"
menu item.
쏅Press the button
7 to open the entry
menu.
You can now enter the PIN:
쏅Turn the volume control
4 to select a digit
for the respective position.
쏅Press the or button
7 to reach the next
or previous position.
Note:
While entering the PIN, you cannot change
the volume of the car sound system.
쏅Press the button 7 repeatedly until you
reach past the last position to conrm the PIN
entered and return to the Bluetooth® menu.
Managing paired devices
In the Bluetooth® menu, you can manage the
paired Bluetooth® devices (cell phones and
streaming devices such as MP3 player).
In the device lists for cell phones and stream-
ing devices, the Bluetooth® names of the paired
devices are displayed. You can do the following:
• Disconnecting the connection to the currently
connected Bluetooth® device
• Establishing a connection to one of the paired
Bluetooth® devices
• Unpairing a Bluetooth® device
쏅In the Bluetooth® menu, select the menu item
"PHONE LIST" or "STREAMING LIST".
쏅Press the button
7 to open the selected
list.
The rst device on the list is displayed.

17
ENGLISH
Note:
If no device is paired, "NO DEVICE" is briey
displayed.
쏅Press the / button 7 once or several
times to select another device.
쏅Press the button
7 to select between the
following options:
To connect the selected device,
쏅press the / button
7 repeatedly until
the "CONNECT DEVICE …" menu item is se-
lected.
쏅Press the button
7 to connect the device.
As soon as the device is connected, "CON-
NECTED" is briey displayed and you are re-
turned to the Bluetooth® menu.
Note:
If no connection can be established, the
display briey shows "CONNECT FAILED". If
the device is already connected, the display
briey shows "CONNECTED".
To disconnect the connection to the selected de-
vice,
쏅press the / button
7 repeatedly until
the "DISCONNECT DEVICE …" menu item is
selected.
쏅Press the button
7 to disconnect the de-
vice.
The display briey shows "DISCONNECTED"
and you are returned to the Bluetooth® menu.
To unpair the selected device,
쏅press the / button
7 repeatedly until
the "DELETE DEVICE …" menu item is selected.
쏅Press the button
7 to unpair the device.
The display briey shows "DELETED" and you
are returned to the Bluetooth® menu.
Unpairing all paired devices
쏅In the Bluetooth® menu, select the "DELETE
ALL PAIRED DEVICES" menu item.
쏅Press the button
7 to unpair all cell
phones or streaming devices.
The display briey shows "ALL DEVICES
DELETED".
External audio sources
Front AUX-IN socket
Danger!
Increased risk of injury from
connector.
In case of an accident, the protruding connector
in the front AUX-IN socket may cause injuries. The
use of straight plugs or adapters leads to an in-
creased risk of injury.
For this reason, we recommend using angled jack
plugs.
As soon as an external audio source, such as a
portable MP3 player is connected to the front
AUX-IN socket
: , it can be selected with the SRC
button 1 . "AUX" then appears on the display.
Sound settings
The following sound settings can be changed in
the "AUDIO" menu:
• Adjusting bass and treble
• Setting the left/right volume distribution
(Balance) or front/rear (Fader)
• Adjusting the increase of bass at low volume
(X-Bass)
• Selecting a sound prole (Presets)
Note:
To increase the volume and sound volume
in the driver's cab, an amplier or active sub-
woofer can be added and connected to the
car sound system.
Calling and exiting the "AUDIO"
menu
쏅Briey press the MENU button < to open
the user menu.
쏅Press the / button
7 repeatedly until
the "AUDIO" menu item is selected.
쏅Press the button
7 to open the "AUDIO"
menu.
Bluetooth® | External audio sources | Sound settings

18
쏅Press the / button 7 repeatedly until
the desired menu item is selected.
쏅Perform the setting (see the next section).
쏅Briey press the MENU button
< to exit the
menu.
Notes:
• The menu is automatically exited approx.
30 seconds after the last button activation
and you are returned to the display of the
current audio source.
• In the menu, you can press the button
7 in each case to return to the higher
menu level.
Making settings in the "AUDIO"
menu
BASS
Bass level. Settings: –7 to +7.
쏅Press the button 7 to open the submenu.
쏅Turn the volume control
4 to perform the
setting.
TREBLE
Treble. Settings: –7 to +7.
쏅Press the button
7 to open the submenu.
쏅Turn the volume control
4 to perform the
setting.
BALANCE
Left/right volume distribution. Settings: L9 (left)
to R9 (right).
쏅Press the button
7 to open the submenu.
쏅Turn the volume control
4 to perform the
setting.
FADER
Front/rear volume distribution. Settings: R9 (rear)
to F9 (front).
쏅Press the button
7 to open the submenu.
쏅Turn the volume control
4 to perform the
setting.
Sound settings | User settings
X-BASS
Increase of bass at low volume. Settings: OFF, 1, 2,
3 (highest increase).
쏅Press the button 7 to open the submenu.
쏅Turn the volume control
4 to perform the
setting.
PRESETS
Selecting equalizer presettings. Settings: POP,
ROCK, CLASSIC, EQ OFF (no presetting).
쏅Press the button
7 to open the submenu.
쏅Turn the volume control
4 to perform the
setting.
User settings
Calling the user menu and selecting
a menu
쏅Briey press the MENU button < to open
the user menu.
In the user menu, the user settings can be found in
the following menus:
• TUNER
• AUDIO (see chapter "Sound settings")
• DISPLAY
• VOLUME
• VARIOUS
• BLUETOOTH
(Professional only, see chapter "Bluetooth®")
쏅Press the / button
7 repeatedly until
the desired menu is selected.
쏅Press the button
7 to open the selected
menu.
쏅Press the / button
7 repeatedly until
the desired menu item is selected.
쏅Perform the setting (see the following sec-
tions).
쏅Briey press the MENU button
< to exit the
menu.

19
ENGLISH
User settings
Notes:
• The menu is automatically exited approx.
30 seconds after the last button activation
and you are returned to the display of the
current audio source.
• In the menu, you can press the button
7 in each case to return to the higher
menu level.
Making settings in the "TUNER"
menu
RDS
Switching the RDS function on or o. Settings: ON,
OFF.
쏅Press the button 7 to open the submenu.
쏅Turn the volume control
4 to change be-
tween the settings.
TRAFFIC (trac information)
(only for reception area EUROPE)
Only possible in FM radio mode: Switching prior-
ity for trac announcements on or o. Settings:
ON, OFF.
쏅Press the button
7 to open the submenu.
쏅Turn the volume control
4 to change among
the settings.
If priority is switched on for trac information, the
display shows the icon .
TUN BAND (band selection)
Activating or deactivating memory banks.
Memory banks that can be deactivated:
Region Memory banks
EUROPE FM2, FMT, MW, LW, SW
USA FM2, FMT, AM, AMT, SW
S-AMERICA FM2, FMT, AM, AMT, SW
THAILAND FM2, FMT, AM, AMT, SW
Settings in each case: ON, OFF.
쏅Press the button
7 to open the submenu.
쏅Press the / button
7 repeatedly until
the desired memory bank is displayed.
쏅Press the button
7 to change the setting.
쏅Turn the volume control
4 to toggle be-
tween the settings ON (activate memory
bank) and OFF (deactivate memory bank).
Deactivated memory banks are skipped during
the source selection with the SRC button
1 .
Note:
If a memory bank is deactivated, the stations
stored in this memory bank are retained.
REGIONAL
(only for reception area EUROPE)
Only possible in FM radio mode: Switching
REGIONAL function on or o. Settings: ON, OFF.
쏅Press the button 7 to open the submenu.
쏅Turn the volume control
4 to change be-
tween the settings.
SEEK SENS
Setting the sensitivity of station seek tuning.
Settings: LO1 (lowest) – HI6 (highest).
쏅Press the button
7 to open the submenu.
쏅Turn the volume control
4 to change be-
tween the settings.
PTY
Switching the PTY function on or o. Settings: ON,
OFF.
쏅Press the button
7 to open the submenu.
쏅Turn the volume control
4 to change be-
tween the settings.
PTY LANG
(only for reception area EUROPE)
Select the language for the display of the pro-
gramme types. Settings: ENGLISH, DEUTSCH (Ger-
man), FRANCAIS (French).
쏅Press the button
7 to open the submenu.
쏅Turn the volume control
4 to select a lan-
guage.

20
AREA (reception area)
Select the reception area for the radio reception.
Settings: EUROPE, USA, S-AMERICA, THAILAND.
쏅Press the button 7 to open the submenu.
쏅Press the / button
7 to select a recep-
tion area.
쏅Press the button
7 to set the reception
area.
쏅Press the button
7 to conrm the selected
reception area.
Making settings in the "DISPLAY"
menu
DIM DAY/DIM NIGHT
Setting the display brightness for the day (DIM
DAY) or the night (DIM NIGHT). Settings: 1 – 16.
쏅Press the button 7 to open the submenu.
쏅Turn the volume control
4 to perform the
setting.
If your car sound system is installed as described
in the installation instructions and your vehicle
features the corresponding connection, the dis-
play brightness for day and night is switched by
switching the vehicle lighting on or o.
SCROLL
Select the display of scrolling text (e.g. when
displaying MP3 le names) either as single display
or continued display. Settings: X1 (single display),
ON (continued display).
쏅Press the button
7 to open the submenu.
쏅Turn the volume control
4 to change be-
tween the settings.
Making settings in the "VOLUME"
menu
ON VOLUME
Setting the power-on volume. Settings: 1 – 45.
쏅Press the button 7 to open the submenu.
쏅Turn the volume control
4 to set the desired
power-on volume.
LAST VOL
If you select the setting LAST VOL, every time you
switch on the radio, the volume level that was set
the last time you switched the radio o is activated
again. Settings: ON, OFF.
Danger!
High volume
The power-on volume can be unex-
pectedly high if the LAST VOL setting is selected
and a high volume was set the last time the radio
was switched o.
Always set the device to a moderate volume.
쏅Press the button
7 to open the submenu.
쏅Turn the volume control
4 to change be-
tween the settings.
TA VOLUME
(only for reception area EUROPE)
Setting the minimum volume for trac announce-
ments. Settings: 1 – 40.
쏅Press the button
7 to open the submenu.
쏅Turn the volume control
4 to perform the
setting.
TEL VOL
(Professional, only with connected cell phone)
Adjusting the minimum volume for telephone
calls. Settings: 1 – 40.
쏅Press the button
7 to open the submenu.
쏅Turn the volume control
4 to perform the
setting.
Note:
During the call, you can adjust the volume
with the volume control
4 .
BEEP
Switching the conrmation beep on or o. Set-
tings: ON, OFF.
쏅Press the button
7 to open the submenu.
쏅Turn the volume control
4 to perform the
setting.
User settings