Blaupunkt GTx 1 Series User manual

Operating and Installation Instructions
2-WAY COAXIAL SPEAKERS
GTx 1xxx SERIES
GTx 1352
GTx 1662
GTx 1402
GTx 1692

Disclaimer
In no event shall Blaupunkt be liable for any
direct, indirect, punitive, incidental, special
consequential damages to property or life and
whatsoever arising out of or connected with the
use or misuse of our products.
USA & CANADA: This product is not intended
for sale in the United States and Canada. If
purchased in the U.S. or Canada, this product is
purchased on as-is basis. No warranty, whether
expressed or implied is provided in the U.S. or
Canada.
Recycling and Disposal
Do not dispose of your old unit in
the household trash!
Use the return and collection
systems available to dispose of
the old device.
This manual may be updated from time to time
without any notice.
solely via the right or left channel is also pos-
sible since the low-frequency portion of the
music is generally identical on both channels.
1
INTRODUCTION
Proper system planning is vital in order to
maximize the device’s performance and road
safety. Plan your installation carefully to avoid
compromising performance reliability of the
system. Consult an authorized Blaupunkt delaler
for installation or reparation. Read the manual
carefullt before operating the device for the
rst time.
Safety Notes
Ensure to folow below safety notes during
installation and wiring connection: -
•
•
•
•
Installation and Connection Instructions
•
•
•
Voltage Supply
•
•
•
Disconnect the negative terminal of the
battery. Refer to the safety notes of the vehcle
manufacturer.
Ensure positions of the holes are nowhere near
the vehicle component to avoid any damage
during drilling.
Ensure cross section of the cable is no less
than 2.5mm if the positive and negative
cables are too long.
Incorrect installation may result in malfunction
of the device or the car sound system.
Select a dry and well-ventilated location to
install the device.
The device must not be installed in overly
exposed location such on therear shelf, rear
seat etc.
The installation location must be suitable for
screw holes and have stable ground support.
Use the supplied power extension cable to
connect to the positive battery terminal.
Firmly and carefully connect the ground lead
to a bare metal point on the vehicle chassis.
The control of the device should be a
two-channel control, either via the preampli-
er output of the car sound system. A control

Pair of 3.5”2-way coaxial speaker with Polypropylene Cone Composition including mounting
hardware
•
•
•
•
•
•
•
Max. Power Handling : 60W
Normal Output Power (RMS) : 20W
Impedance : 4ohms
Frequency Response : 120Hz - 20,000Hz
Sensitivity : 90±3dB
Mounting Depth : 41mm
Diameter Hole : 78mm
2
SPECIFICATION
GTx 1352
4.8mm
105mm
53mm
41mm
70mm
78mm
119mm
88mm
Accessories
Screws (4x32mm) x2 U Clips x2

Pair of 4.0”2-way coaxial speaker with Polypropylene Cone Composition including mounting
hardware
•
•
•
•
•
•
•
Max. Power Handling : 70W
Normal Output Power (RMS) : 22W
Impedance : 4ohms
Frequency Response : 100Hz - 20,000Hz
Sensitivity : 90±3dB
Mounting Depth : 47mm
Diameter Hole : 95mm
3
SPECIFICATION
GTx 1402
4.5mm
117mm
67mm
142mm
47mm
95mm
70mm
Accessories
Screws (4x32mm) x4 U Clips x4

Pair of 6.5”2-way coaxial speaker with Polypropylene Cone Composition including mounting
hardware
•
•
•
•
•
•
•
Max. Power Handling : 110W
Normal Output Power (RMS) : 33W
Impedance : 4ohms
Frequency Response : 70Hz - 20,000Hz
Sensitivity : 90±3dB
Mounting Depth : 56mm
Diameter Hole : 145mm
4
SPECIFICATION
GTx 1662
4.5mm
156mm
75m
m
173mm
56mm
145mm
80mm
Accessories
Screws (4x32mm) x4 U Clips x4

Pair of 6.0”x 9.0”2-way coaxial speaker with Polypropylene Cone Composition including mounting
hardware
•
•
•
•
•
•
•
Max. Power Handling : 115W
Normal Output Power (RMS) : 35W
Impedance : 4ohms
Frequency Response : 60Hz - 20,000Hz
Sensitivity : 90±3dB
Mounting Depth : 74mm
Diameter Hole : 153mm x 220mm
5
SPECIFICATION
GTx 1692
119mm
4.5mm
167mm
105mm
252mm
80mm
220mm
74mm
179mm
153mm
Accessories
Screws (4x32mm) x4 U Clips x4

6
INSTALLATION
SPECIFICATION
GTx 1352
GTx 1662
GTx 1402
GTx 1692
Problems Possible Causes Solutions
Speaker does not
work
Incorrect or loose wiring
connection.
Ensure proper wiring connections of
speaker.
Fraying or broken cables. Repair or replace if the cables are damaged.
Speaker is damaged. Replace with a new speaker.
Distorted and hissing
sound
Voice coil or speaker cone
is damaged.
Replace with a new speaker.
If any of the following problem occur, please resort to Troubleshooting for the possible solutions.
Consult Blaupunkt authorized dealer if problem persist.

Designed and engineered by Blaupunkt Competence Centre
GTx 1352
4 111 21 042 58 01
GTx 1402
4 111 21 040 58 01
GTx 1662
4 111 21 039 58 01
GTx 1692
4 111 21 041 58 01