Blossom Pillar MCL1 2032L User manual

Specifcation & Installation Guide
[ ]
www.blossomus.com
MCL1 2032 (L/R)
Pillar
Asta
MCL2 2032 (L/R)
20"
20"
24"
24"
30"
30"
MCL1 2432 (L/R)
MCL2 2432 (L/R)
MCL1 3032
MCL2 3032
Combined with two 24"
(MCL1 2432L + MCL1 2432R)
Combined with two 30"
(MCL1 3032 x 2)
48" 60"
Combined with two 24"
(MCL2 2432L + MCL2 2432R)
Combined with two 30"
(MCL2 3032 x 2)
48" 60"
MEDICINE
CABINET

IMPORTANT SAFETY INSTRUCTIONS
ELECTRIC CONNECTIONS
When using an electrical furnishing, basic precautions should always be followed, including the
following:
WARNING: To reduce the risk of burns,fire,electric shock or injury to persons. Use
this furnishing only for its intended use as described in these instructions. Do not
use attachments not recommended by the manufacturer. Never drop or insert any
object into any opening.Do not use outdoors.
WARNING: Risk of electric shock. Connect this furnishing to a properly grounded
circuit only. See grounding instructions.
CAUTION: This product must be connected to a grounded metal permanent
wiring system or an equipment-grounding conductor must be run with the circuit
conductors and connected to the equipment grounding terminal or lead on the
product.
WARNING: An Electrical option cabinet must be wired to a 20 Amp GFI (Ground
Fault Interrupter) protected circuit when used in bathrooms and all other locations
required by the National Electric Code.
ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENCED ELECTRICIAN.
WARNING: Shut off power before wiring the cabinet.
CAUTION: Requires 120 VAC 20 Amp GFI protected Circuit.
HARDWARE AND TOOLS
DIMENSIONS
GROUNDING INSTRUCTIONS:
Line/Black
Field Wire
Grouund/Green
Neutral/White
L
N
L
N
2
Make connections
The electric wire comes through
the access hole in the side of the
cabinet.
* Wire terminal plate is not included.
Neutral to white.
Line to black.
Ground to green.

HARDWARE AND TOOLS
DIMENSIONS
Hardware Tools (not includes)
NO. Draw QTY(pcs)
A Top mounting bracket 2-3
BBottom mounting
bracket 1
C Hardware screw 6-10
D Glass side panel 2
E Glass Shelf 3
F Shelf support bracket 6
G Connector 2
Item
Model No A B C Rough in size
Pillar
MCL1 2032L MCL1 2032R 20" 32" 5" 18-3/8" x 30-3/8" x 4"
MCL1 2432L MCL1 2432R 24" 32" 5" 22-3/8" X 30-3/8" x 4"
MCL1 3032 / 30" 32" 5" 30-3/8" x 30-3/8" x 4"
Asta
MCL2 2032L MCL2 2032R 20" 32" 5" 18-3/8" x 30-3/8" x 4"
MCL2 2432L MCL2 2432R 24" 32" 5" 22-3/8" X 30-3/8" x 4"
MCL2 3032 /30" 32" 5" 30-3/8" x 30-3/8" x 4"
NOTE: Determine overall medicine cabinet
dimensions. If recess medicine cabinet,determine
rough-in (Wall Cut-out) dimensions.
NOTE: All rough-in dimensions for reference only!
A-Cabinet's Width
B-Cabinet's Height
C-Cabinet's Depth
3
Electric Drill
Screw Driver
1/8" Drill Bit
Silicone
Lever
Pencil or Marker
Tape Measure

PRIOR TO MOUNTING
CONNECTING CABINETS(OPTIONAL RECESS MOUNTING)
RECESS MOUNT INSTALLATION CONTINUED
4
1
3
2
4
Carefully remove side mirror panels for recess mount
installation.
While supporting the door release(the lever under the hinge
arm),slide the door off the frame.
Connect cabinets with connectors provided. Measure single or combined connected cabinet rough in size.
Remove door(s) prior to mounting your cabinet.Start with
unplugging the door from the cabinet.
Take off the door(s) carefully and lay it down on a safe area.
For recess mount only!

RECESS MOUNT INSTALLATION CONTINUED
L
N
L
N
L
N
L
N
L
N
L
N
3” mininum
5
4
2
5
3
1
6
Draw the perimeter of the cabinet on the wall.
Connect electrical wires before inserting the cabinet into the
opening.
Affix using hardware screws into the studs.Position cabinet in cutout opening.
Be careful to avoid
squeezing the wiring
while insert the
cabinet.
Cut the marked perimeter with suitable tool.
Frame the opening for the cabinet based on the
measurements.

SURFACE MOUNT INSTALLATION
3” mininum
L
N
L
N
6
1
3
6
2
4
7
5
8
Level and mark the cabinet's locationon the wall. Attach bottom bracket to wall.
With assistance rest the cabinet on the
mounting bracket and hold in place.
Attach the top mounting bracket to
the wall using a screw gun.
Top mounting brackets must be
attached to furring strip/channel or wall
studs.
Insert top mounting bracket into the top
of the cabinet.
Test the fit of the cabinet before Final
assembly.
Make sure cabinet is leveled and
fully inserted into the groove of
the bottom bracket.
Connect the electrical wires.
Make sure top brackets are locked in the
grooves.
Bottom mounting
brackets must be attached to
furring strip/channel or wall
studs

FINAL ASSEMBLY
7
OPTIONAL DOOR ADJUSTMENT
Doors may need to be adjusted after the
initial shipping of the cabinet. The cabinet
doors have a three-way adjustment feature.
Height, side-to side, level and depth can be
adjusted. With the hinge slightly closed you
can access the middle screw for up/down
adjustment.
With the hinge fully extended you can access
the front and back screws. These screws will
move the door side to side and in and out.
1. Slide the doors into place by pinching the end of the hinges.
2. Plug the door into the cabinet.
1. Adjust the shelf support brackets position:
Unscrew the screws for shelf support bracket then slide the bracket up or down can adjust the bracket into the desired
location.A level can be used to make sure left and right brackets are level. Screw the brackets to secure in position.
2. Insert the shelves into shelf support brackets at left and right sides.
3. Screw the rubber screws of shelf support brackets to fasten the glass shelves.

How to use touch sensor switches:
Touch the left switch to turn on/off the LED lights and Mirror Defogger.
Touch the Dimmer switch to adjust the LED light color, Press and hold the dimmer switch to dim or
brighten the lights brightness. Dimmer switch stores the current light level intensity when switched off and on.
Use and Maintenance:
The interior is constructed of mirrored glass and aluminum. Use only a damp cloth to clean. Ammonia or vinegar-
based cleaners can damage mirrors.
When cleaning, spray the cloth, not the mirror, or surrounding surfaces. Do not use abrasive cleansers on any part
of the light fixture.
prior notice.
luxury made simple
Blossom Kitchen & Bath Supply Corporation
(718)-366-0088 | [email protected] | www.BlossomUS.com