BLUE MANGO TECH BMH-S128 User manual

Distributed by
PRINTED IN KOREA
P/N : 388037075
INSTRUCTION MANUAL
- Before attempting to connect or operate this product, please read these instructions carefully and
save this manual for future use.
- The design and specifications are subject to change without prior notice to improve product’s quality.
FULL HD MEGA PIXEL
ZOOM CAMERA

The lightning flash with an arrowhead symbol
within an equilateral triangle is intended to alert
the user to the presence of uninsulated
dangerous voltage within the product's enclosure
that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying
the product.
REGULATORY INFORMATION : FCC Part 15 WARNING -
Do not install this equipment in a confined
space such as a bookcase or similar unit.
Disposal of your old appliance
1.
When this crossed-out wheeled bin symbol
is attached to a product it means the product
is covered by the European Directive
2002/96/EC
2.
All electrical and electronic products should
be disposed of separately from the municipal
waste stream via designated collection facilities
appointed by the government or the local
authorities
3. The correct disposal of your old appliance
will help prevent potential negative conse-
quences for the environment and human
health
4.
For more detailed information about disposal
of your old appliance, please contact your
city office, waste disposal service or the shop
where you purchased the product.
To disconnect power from the mains, pull out the main
cord plug. When installing the product, ensure that the
plug
is easily accessible.
WARNING - Wiring methods shall be in accordance with
the National Electric Code, ANSI/NFPA 70.
WARNING - To reduce a risk of fire or electric shock, do
not expose this product to rain or moisture.
CAUTION - This installation should be made by a qualified
service personrel and should conform to all local codes.
CAUTION - To avoid electrocal shock, do not open the
cabinet. Refer servicing to qualified personnel only.
CAUTION -
The apparatus should not be exposed to
water (dripping or splashing) and no objects filled with
liquids, such as vases, should be placed on the apparatus.
WARNING - This is a class A product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take adequate
measures.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION :
FCC WARING - This equipment may generate or use
radio frequency energy. Changes or modifications to
this equipment may cause harmful interference unless
the modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference
in which case the user will be required to correct the
interference at his own expense.
- A suitable conduit entries, knock-outs or glands shall
be provided in the cable entries of this product in the
end use.
-Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall
be provided with brushings.
03

1. Read these instructions - All these safety and operating
instructions should be read before the product is operated.
2. Keep these instructions - The safety, operating and user
instructions should be retained for future reference.
3. Heed all warnings - All warnings on the product and in
the operating instructions should be adhered to.
5. Do not use this apparatus near water - For example :
near a bath tub, wash bowl, kitchen sink, laundry tub,
in a wet basement, near a swimming pool, etc.
6. Clean only with dry cloth - Unplug this product from
the wall outlet before cleaning. Do not use liquid cleaners.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions. -
Slots and openings in the cabinet are provided for
ventilation, to ensure reliable operation of the product,
and to protect it from overheating. The openings should
never be blocked by placing the product on a bed, sofa,
rug or other similar surface. This product should not
be placed in a built-in installation such as a bookcase
or rack unless proper ventilation is provided and the
manufacturer’s instructions have been adhered to.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
4.
Follow all instructions - All operating and user instructions
should be followed.
9.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
10.
Only use attachments/accessories specified by the
manufacturer.
12. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
04 05
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS
11. Unplug this apparatus during lightning storms or
when unused for long periods of time.

06 07
CONTENTS FEATURES
Features
SPECIAL FUNCTION ..............................
DISPLAY ..............................................
SPECIFICATION ........................................
DRAWING ................................................
TROUBLESHOOTING ................................
26P
28P
30P
34P
36P
FEATURES .....................................................
PACKAGE COMPONENTS ...............................
SYSTEM CONFIGURATION .............................
PART NAMES AND FUNCTIONS .....................
CONNECTIONS .............................................
EXTERNAL DEVICE CONNECTIONS ...............
VIDEO OUT ...................................................
MENU OPERATION ........................................
MAIN MENU ..................................................
FOCUS ......................................................
EXPOSURE ...............................................
WHITE BALANCE ......................................
IMAGE ......................................................
INTELLIGENCE .........................................
7P
8P
9P
10P
12P
13P
14P
15P
16P
17P
18P
21P
22P
24P
• 1/2" Sony CMOS sensor
• x12, x30 Optical Zoom
• Full HD Resolution
1920x1080p / 30fps(25fps),1920x1080p / 60fps(50fps), 1280x720p / 30fps(25fps), 1280x720p / 60fps(50fps)
• Day & Night (ICR)
• WDR (Wide Dynamic Range)
• DNR (Digital Noise Reduction, 2D+3D)
• DIS (Digital Image Stabilization)
• EX-SDI (Long Reach)
• Privacy Mask Function
• On Screen Display
• Intelligent Motion Detection
• Multi-Protocol(VISCA, Pelco-D, Pelco-P)

08 09
PACKAGE COMPONENTS SYSTEM CONFIGURATION
RS485
RS485
RS485
DVR
Keyboard
TV Monitor
VIDEO
VIDEO
VIDEO
(HDMI)
[Optional Remote Controller]
CAMERA
MANUAL
CABLE
· ·
··
·
·
·
Not used
Far / Right
Tele/ Up
Menu/ Set
Wide / Down
Near / Left

10 11
PART NAMES AND FUNCTIONSPART NAMES AND FUNCTIONS
【1】Camera installation bracket
The braket can be fixed at the top or bottom of the
camera.
【1】【1】OSD / Zoom / Focus control
【2】HDMI
【3】DIGITAL-OUT
【4】HD-SDI
【5】EX-SDI
【6】ANALOG-OUT
【7】CVBS
【8】HD-TVI
【9】Power LED
【10】Control Terminal
1: RS-485 (+)
2: RS-485 (-)
3: Motion Detection Out
4: No Connection
5: Ground
6: Day&Night Input (Low : Night, High : Day)
【11】AD Key
1: GND
2: AD-key
3: GND
【12】Power : DC12V
【1】 【2】
【3】
【4】
【5】
【6】
【7】
【8】
【9】
【10】
【11】 【12】

12 13
CONNECTIONS EXTERNAL DEVICE CONNECTIONS
Basic connection
The peripheral devices (DVR, monitor, lens, etc), DC adaptor
and cables are not supplied.
1. Connecting the monitor.
Make the video signal connection between the camera and the
monitor or time lapse monitor or DVR.
2. Use a commercially available DC12V adaptor.
Connect an DC 12V power source to the DC 12V input terminal
on the back of the camera.
3. Insert the plug of this power cord into a wall outlet.
The POWER indicator will light. Adjust the picture on the monitor
using the Brightness and Contrast controls etc.
RS-485 COMMUNICATION
Connect to an external controller of RS-485 format.
Motion Detection Out
When the motion detection function is working.
DC3.3V is outputed to OUT pin and GND pin.
Day & Night input
Day/Night mode of the camera can be switched by
signal from an external device.
To use this function, <DAY&NIGHT> setting of the
camera should be set to the <EXT>.
Note : Use a relay unit if the voltage or current of the
connected
device exceeds the ratings.
To monitor’s Video Input
or Camera Input
2
3
1
DC12V

14 15
MENU OPERATIONVIDEO OUT
This camera utilizes an on-screen user MENU. To set items
on the menu, use the following buttons on the side panel.
Tele(Up) button : Zoom in, Tele (Moves the cursor
upwards. Use this button to select an item or
adjust the parameters.)
Wide(Down) button : Zoom out, Wide (Moves the
cursor downwards. Use
this button to select an
item or adjust the parameters.)
Far(Right) button : Adjust focus in Manual Mode
(Moves the cursor to the right. Use this button to
select or adjust the parameters of the selected
item. The parameter changes each time this
button is pressed.)
Near(Left) button : Adjust focus in Manual Mode
Moves the cursor to the left. Use this button to
select or adjust the parameters of the selected
item. The parameter changes each time this
button is pressed.)
Set button : Executes selections and displays a
submenu for an item with the mark.
ANALOG OUT
Select CVBS and HD-TVI video out
by switch setting.
DIGITAL OUT
Select HD-SDI and EX-SDI video out
by switch setting.

16 17
FOCUSMAIN MENU
Camera menu is subject to change without prior notice to upgrade and quality increase and we may use
slip sheet for the change.
Please check the camera version and the slip sheet if the camera menu and this manual menu is not matched.
MAIN MENU
Functions can be setup using “Menu Key Command” of Visca protocol.
The menu consists of the “Main Menu” and “Sub Menu”.
The main menu is displayed where 7 camera functions can be selected.
To the push of each main menu selection, the sub-menu is displayed
If you want save the menu, select [SAVE].
If you want not save the menu, select [EXIT]
(After select , Power off -> on)
If you want default the menu, select [DFLT]
MENU
FOCUS
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
[EXIT] [SAVE] [DFLT]
FOCUS
MENU
FOCUS
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
[EXIT] [SAVE] [DFLT]
FOCUS
MODE
DISTANCE
ZOOM SPEED
LENS REFRESH
E.ZOOM
ZOOM PRESET
[BACK] [SAVE] [DFLT]
◈MODE : Select auto focus mode
► AUTO, ONE PUSH, MANUAL
◈DISTANCE : Select minimum distance in focus between camera and object.
► 0.1 / 1.0 / 3.0 / 5.0 / 10.0 m(x12 Camera) ►0.1 / 1.5 / 3.0 / 5.0 / 10.0 m(x30 Camera)
◈ZOOM SPEED : Select Zoom Speed
► 0 (Slow) ~ 7 (Fast)
◈LENS REFRESH : Lens origin calibrated automatically.
►ONE PUSH↲ / ON (1 day ~ 10 days)
◈ E .ZOOM : Select maximum digital zoom magnification.
► OFF / ON (max x2 ~ x19, x21, x23, x25, x28, x32)
◈ ZOOM PRESET : Select zoom preset
► PRESET # : Select Zoom preset number (1 ~ 5)
► MODE : OFF / ON↲
▷ON↲: Adjust the Zoom Position
AUTO
1.0m
ONE PUSH
OFF
7

EXPOSURE
MODE
AGC
SHUT SPEED
IRIS
DSS
FLICKERLESS
BRIGHTNESS
WDR/BLC
DAY&NIGHT
[BACK] [SAVE] [DFLT]
AUTO
ON
---
---
OFF
OFF
OFF
8
18 19
EXPOSURE EXPOSURE
◈ DSS : Select maximum DSS (Digital Slow Shutter)
* 60 / 50 fps mode
► OFF / x2, x4, x8
* 30 / 25 fps mode
► OFF / x2, x4
◈FLICKERLESS : Select Flickerless mode
► OFF / ON (remove screen flicker)
◈BRIGHTNESS : Adjust brightness level
► 0(dark) ~ 20(bright) steps
◈ WDR/BLC : Select WDR(Wide Dynamic Range) or BLC(Back Light compensation)
► WDR↲
▷LEVEL : Adjust WDR level.
► LOW, MID-LOW, MIDDLE, MID-HIGH, HIGH
※ WDR doesn’t work in Manual Exposure Mode and Shutter Priority Mode.
※When WDR on, CVBS output is disabled.
► BLC↲
▷POSITION : Adjust the window position
▷ SIZE : Adjust the window size
※Can’t use WDR and BLC at the same time.
(When WDR On, BLC is Off. And when BLC is On, WDR is Off)
※ BLC doesn’t work in Manual Exposure Mode.
EXPOSURE
MENU
FOCUS
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
[EXIT] [SAVE] [DFLT]
◈ MODE : Select Exposure Mode
►AUTO / IRIS.P / SHUT.P / MANUAL
◈AGC : Select Auto Gain Control
► OFF / ON (AUTO, SHUT.P or IRIS.P Mode)
► 0 ~ 10 (MANUAL Mode)
◈SHUT SPEED : Can be set in SHUT.P or MANUAL mode
* 60 / 50 fps mode ► x8, x4, x2, 1/60(50), 1/120(100), 1/250, 1/700, 1/1000,
1/1600, 1/2500, 1/5000, 1/7000, 1/10000, 1/30000 sec
* 30 / 25 fps mode ► x4, x2, 1/30(25), 1/60(50), 1/120(100), 1/250, 1/700, 1/1000,
1/1600, 1/2500, 1/5000, 1/7000, 1/10000, 1/30000 sec
◈IRIS : Iris level can be set in IRIS.P or MANUAL mode
► 0 ~ 20

20 21
EXPOSURE WHITE BALANCE
◈DAY&NIGHT : Select Day&Night
► MODE : AUTO↲ / EXT-IN↲ / DAY / NIGHT↲
▷AUTO
► DELAY : 0 ~ 255 sec
► THRS : 0 ~ 28
Day↔Night switching level in Auto Mode.
Switching in lower lux with lower threshold level.
► GAP : LOW, MID-LOW, MIDDLE, MID-HIGH, HIGH
Margin between Day→Night switching level and Night→Day switching level.
► IR DETECTION : Setting IR Detection mode. (ON / OFF)
► IR DET LEVEL : Setting IR Detection level. (LOW, MID-LOW, MIDDLE, MID-HIGH, HIGH)
► BURST : OFF / ON
▷EXT-IN
► DELAY : 0 ~ 255 sec
► BURST : OFF / ON
► POLARITY : External Input polarity (ACTIVE LOW / ACTIVE HIGH)
▷NIGHT
► BURST : OFF / ON
WHITE BALANCE
MENU
FOCUS
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
[EXIT] [SAVE] [DFLT]
WHITE BAL
MODE
RED GAIN
BLUE GAIN
CHROMA
[BACK] [SAVE] [DFLT]
AUTO
- - -
- - -
10
◈AWB : Select WHITE BALANCE mode
► AUTO / ONE PUSH↲ / MANUAL / INDOOR / OUTDOOR
▷AUTO : Automatically adjusts color according to the available lighting.
▷ ONE PUSH : It is a fixed white balance mode that may be automatically
readjusted only by pressing ONE PUSH
▷MANUAL↲: Color can be corrected when the user increases or decreases
“RED GAIN” or “BLUE GAIN”.
▷ INDOOR : Set color temperature to be Indoor light (3700°K)
▷ OUTDOOR : Set color temperature to be Outdoor light (5100°K)
◈ RED GAIN : Adjust R gain value ► 0 ~ 20 steps
◈ BLUE GAIN : Adjust B gain value ► 0 ~ 20 steps
◈ CHROMA : Adjust CHROMA gain value ► 0 ~ 20 steps

◈SHARPNESS : Adjust sharpness level
► 0 ~ 10 steps
◈ACE : Select Digital WDR (Wide Dynamic Range)
► OFF / LOW / MIDDLE / HIGH
◈DEFOG : Carry out defog function
► OFF / ON↲
▷ MODE : AUTO / MANUAL
▷ LEVEL : LOW / MIDDLE / HIGH
※Can’t use DEFOG and ACE at the same time (when DEFOG is On, ACE is Off)
◈FREEZE : Select real or still mode
► OFF / ON
◈GAMMA : Select GAMMA
► 0.45 / 0.55 / 0.65 / 0.75
22 23
IMAGE IMAGE
IMAGE
MENU
FOCUS
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
[EXIT] [SAVE] [DFLT]
◈HLC : Select High Light Compensation.
When extremely bright light is projected to the camera masking is used on the portion
to prevent partial saturation on the monitor.
▷ MODE : OFF / ON / NIGHT
▷ LEVEL : 0 ~ 20 steps
▷ COLOR : 0 ~ 13 steps
◈DNR : Select Digital Noise Reduction
► OFF / LOW / MIDDLE / HIGH / AUTO
◈MIRROR : Select a flip mode
► OFF / H / V / H&V
▷ H : You can flip the picture horizontally on the screen
▷V : You can flip the picture vertically on the screen
▷ H&V : You can flip the picture horizontally & vertically on the screen
IMAGE
HLC
DNR
MIRROR
SHARPNESS
ACE
DEFOG
FREEZE
GAMMA
[BACK] [SAVE] [DFLT]
MIDDLE
OFF
OFF
OFF
OFF
0.55
7

24 25
INTELLIGENCE INTELLIGENCE
INTELLIGENCE
MENU
FOCUS
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
[EXIT] [SAVE] [DFLT]
INTELLIGENCE
PRIVACY
MOTION
DIS
OFF
OFF
OFF
[BACK] [SAVE] [DFLT]
◈PRIVACY : Hide an area you want to hide on the screen
► OFF / ON↲
▷ MASK# : Select mask area number (1 ~ 24)
▷ MODE : Mask enable or disable (OFF / ON)
▷POSITION : Adjust the mask position
▷ SIZE : Adjust the mask size
▷ COLOR : Select mask color (0 ~ 13)
▷ TRANS : Select mask transparency level (0 ~ 4)
◈MOTION : When there is movement of the subject in the screen, there will be an motion detection
► OFF / ON↲
▷ AREA# : Setting 3 areas(1~3) of motion detection
▷ MODE : OFF / ON (Limit and define areas of motion detection)
▷ SENSITIVITY : Adjust sensitivity of MD (0 ~ 20 steps)
More sensitive to setting to low step with sensitivity
▷POSITION : Adjust the Area position
▷ SIZE : Adjust the Area size
▷ INTERVAL :Select the alarm interval time (0 ~ 255sec)
▷ DWELL TIME : Select the duration time about changing MD mode (0 ~ 255sec)
▷ ZOOM PRESET : Select Motion Zoom Preset Mode and Position (OFF / ON↲)
◈ DIS : Select Digital Image Stabilizer mode
► OFF / ON↲
▷ RANGE : Setting the image compensation range. (10%, 20%, 30%)
▷FILTER : Setting the sensitivity to hold DIS function in worst case. (LOW, MIDDLE, HIGH)
▷AUTO C : Setting Auto Centering mode (OFF, HALF, FULL)
OFF
OFF
OFF

26 27
SPECIAL FUNC SPECIAL FUNC
◈ HD PRI. : Select HD output priority (HD-SDI/HDMI)
※ Can’t use HD-SDI and HDMI at the same time in 1080p/60(50)fps
HD-SDI priority : Format is 1080p60(50), If HD-SDI cable is connected, HD-SDI is ON
and HDMI is OFF automatically.
HDMI priority : Format is 1080p60(50), If HDMI cable is connected, HDMI is ON(detection)
and HD-SDI is OFF automatically.
※ Other formats can output HD-SDI/HDMI both.
HD-SDI : 1080p/30(25)fps, 720p/30(25)fps, 720p/60(50)fps
HDMI : 1080p/30(25)fps, 720p/60(50)fps
◈COMM : Set up the camera ID, baud rate, protocol
▷ID : Select the camera ID
► 1 ~ 255
▷BAUD RATE : Select serial communication speed
► 2400 / 4800 / 9600 / 19200 / 38400 / 57600 / 115200bps
▷PROTOCOL : Select operating protocol
► VISCA / PELCO-D / PELCO-P / UPDATE
SPECIAL FUNC
MENU
FOCUS
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
[EXIT] [SAVE] [DFLT]
◈ DEFECT : Compensates for bad pixels that may occur. Occurs when the whole screen is
in full black or if there is bad pixelation and it changes the THRS values until the screen is fixed.
※When you use this function, you have to block the lens for blocking lights into the lens.
◈ IMAGE RANGE : Select image bit range. (Full : 100%, Compressed : 75%)
► FULL, COMP, USER↲
▷ LEVEL : Select user mode level (0 ~ 32)
◈ SYSTEM : Select NTSC(30/60fps) or PAL(25/50fps).
◈ HD FORMAT : Select Digital output (1080p/30(25)fps, 1080p/60(50)fps,
720p/30(25)fps, 720p/60(50)fps)
※1080p60(50) format is available in the TVI switch is off.
SPECIAL FUNC
DEFECT
IMAGE RANGE
SYSTEM
HD FORMAT
HD PRI.
COMM
[BACK] [SAVE] [DFLT]
COMP
NTSC
1080p/30fps
HD-SDI

28 29
DISPLAYDISPLAY
DISPLAY
MENU
FOCUS
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
[EXIT] [SAVE] [DFLT]
◈DISP SEL : Select display item.
► OFF / ON↲
▷ ID : OFF / ON
▷ TITLE : OFF / ON
▷ ZOOM RATIO : OFF / ON
▷ SYSTEM MSG : OFF / ON (MD Alarm)
◈ SET TITLE : Select camera title menu (Text edit– max 40 characters)
◈INIT SEL : Select display initial message.
► OFF / ON↲
▷ ID : OFF / ON
▷ BAUDRATE : OFF / ON
▷ PROTOCOL : OFF / ON
▷ VERSION : OFF / ON
▷ INIT MSG : OFF / ON
DISPLAY
DISP SEL
SET TITLE
INIT SEL
SET INIT MSG
LANGUAGE
[BACK] [SAVE] [DFLT]
ON
ON
ENGLISH
◈ SET INIT MSG : modify initial message. (Text edit – max 40 characters)
◈LANGUAGE : Select language.
► English / Simplified Chinese / Traditional Chinese / Japanese
※ Character Table of Text edit Mode
i

30 31
SPECIFICATION SPECIFICATION
Model
Image Sensor
Total Pixels
Active pixels
Scanning system
Sync. System
Resolution
Min. illumination
Video Output
S/N Ratio
1/2" Sony CMOS Sensor
1952 (H) x 1241 (V) = 2.42M Pixels
1937 (H) x 1097 (V) = 2.12M Pixels
Progressive Scan
Internal
Digital ; 1080p/60(50)fps, 1080p/30(25)fps, 720p/60(50)fps, 720p/30(25)fps
Analog : 700TVL
Color : 0.15 lux , BW : 0.01lux
Color DSS : 0.0375 lux , BW DSS : 0.002 lux
HD-SDI, EX-SDI, HDMI, TVI, CVBS
more than 50dB (AGC off)
Lens type
Zoom Ratio
Focal Length
Aperture Ratio
Angle of View (D, H, V)
x12 Day & Night Zoom Lens
Optical x12, Digital x32 Zoom
f = 7.0 mm ~ 84.0 mm
F1.5 (wide) ~ F1.9 (tele)
x30 Day & Night Zoom Lens
Optical x30, Digital x32 Zoom
f = 6.0 mm ~ 180.0 mm
F1.5 (wide) ~ F4.3 (tele)
Wide
Tele
58.3°
6.5°
51.1°
5.0°
30.0°
3.2°
Mode / Distance / Zoom Speed / Lens Refresh / E.Zoom / Zoom Preset
Auto / One Push / Manual
Focus
Mode
Wide
Tele
68.6°
2.65°
61.2°
2.32°
35.7°
1.31°
Model
Distance
Zoom Speed
Lens Refresh
E.Zoom
Zoom Preset
Exposure
Mode
Gain Control (AGC)
Shutter Speed
Iris
Digital Slow Shutter (DSS)
Flickerless
Brightness
WDR/BLC
Day&Night
White Balance
Image
HLC
DNR
0.1 / 1.0 / 3.0 / 5.0 / 10.0 m
0(Slow) ~ 7(Fast)
One Push / 1 ~ 10Day
Off / MAX x2 ~ x32
5 Preset
Mode / AGC / Shut Speed / Iris / DSS / Flickerless / Brightness / WDR/BLC / D&N
Auto / Iris. Priority / Shut. Priority / Manual
Off / On
1/30(25) ~ 1/30,000 sec
0 ~ 20
Off / x2 / x4 (/ x8 : 60 or 50 fps mode only)
Off / On
0 ~ 20 steps
OFF / WDR / BLC
Auto / Day / Night / Ext-in
Auto / One Push / Manual / Indoor / Outdoor
HLC / DNR / Mirror / Sharpness / ACE / Defog / Freeze / Gamma
Off / On / Night Only
Auto / Off / Low / Middle / High
0.1 / 1.5 / 3.0 / 5.0 / 10.0 m

32 33
SPECIFICATIONSPECIFICATION
Model
Mirror
Sharpness
ACE
Defog
Freeze
Gamma
Intelligence
Privacy Mask
Motion Detection
Digital Image Stabilizer
Special Func
Defect DET
Image Range
System
HD Format
Comm
Display
Off / H / V / H&V
0 ~ 10 steps
Off / Low / Middle / High
Off / On(Auto / Manual)
Off / On
0.45 / 0.55 / 0.65 / 0.75
Privacy / Motion / DIS
Off / On (24 positions)
Off / On (3 positions)
Off / On
Defect / Image Range / System / HD Format / HD-Pri / COMM
One push
Full / Comp. / User
NTSC / PAL
1080p/30(25)fps / 1080p/60(50)fps / 720p/30(25)fps / 720p/60(50)fps
ID : 1 ~ 255
Baud Rate : 2400 / 4800 / 9600 / 19200 / 38400 / 57600 / 115200
Protocol : VISCA / Pelco-D / Pelco- P / Update
Disp Sel / Set Title / Init Sel / Set Init Msg / Language
Model
Disp Sel (Off / On)
Set Title
Init Sel (Off / On)
Set Init Msg
Language
OSD Text
Power Source
Power Consumption
Power Input
Video Output
Storage Temperature
Operating Temperature
ID / Title / Zoom Ratio / System Message
Text Edit
ID / Baud Rate / Protocol / Version / Init. Message
Text Edit
English / Simplified Chinese / Traditional Chinese / Japanese
0 ~ 9 , A ~ Z , a ~ z
9V to 15V DC
400mA
Connector
Connector
-20℃ ~ +60℃((Humidity : 0%RH ~ 90%RH)
-10℃ ~ +50℃((Humidity : 0%RH ~ 90%RH)

34 35
DRAWINGDRAWING
67
74
13.5 10
125 8.6
55.5 14
1/4-20 UNC 2B
Unit : mm
x12 Camera
72.6
80
37
12
154
10
8.5
1470.95
1/4-20 UNC 2B
Unit : mm
x30 Camera

35 36
TROUBLESHOOTING
• Nothing appears on the screen.
-Please check the power connection.
-Please check the video signal line connection.
• The video image is not clear.
-Please clean the lens with a clean cloth or brush.
-Please adjust that the screen is not exposed directly to a bright light.
-Please move the camera if necessary.
• The screen is dark.
-Please adjust the contrast feature of the monitor.
-If you have an intermediate device, set the 75 Ω /Hi-Z properly, and check the terminals.
-Please adjust the brightness level.
• The MOTION DETECTION function is not working
-Please check if “MOTION DETECTION” mode is turned on.
-Please check if the MD Sensitivity is too high.
-Please check the setting of the MD AREA.
• The WDR function is not working
-Please check if the WDR Level is too low.
-Please check if the AE Mode is set to MANUAL. The WDR doesn’t work in MANUAL,
Shutter priority Exposure mode.
• Colors are not quite right.
-Please check if the camera is facing directly into sunlight or fluorescent light.
• The Day&Night function doesn’t work.
- Please check if the AGC of EXPOSURE menu is set to OFF.
- The Auto Day&Night doesn’t work in AGC OFF status.
Trouble shooting
If there are problems in operation, please refer to the items below.
If the problem persists, please contact the agent you purchased this product from.