Blue Thumb Fountain Vase User manual

ENJOY YOUR FOUNTAIN AT NIGHT
BY ADDING LIGHTS!
Email a Picture of your completed installation to
[email protected]
*Blue Thumb proudly manufactures their products in Saginaw, Michigan
3 Pack Fountain Light Kit
Blue Thumb Item# PB2897
Fountain Vase
Installation Manual

STEP 1
Clear/level area
based on the size
of the basin type
plus 1-2” width
and length.
STEP 2
Dig hole to size
and depth of
the basin. Keep
in mind the
basin should sit
approximately
1” below grade
once installation is
complete.
STEP 3
Level the bottom of
the hole with sand
or small gravel and
tamp to ensure no
settling occurs after
installation.
STEP 4
Set basin in the hole
and verify that the
box top is level and
approximately 1”
below grade.
If you will be using
a liner bib, ensure
surrounding area
gently slopes toward
the basin to ensure
water makes its way
back to the basin.
STEP 5
Backll void between box and soil with a self-compacting material such
as sand or pea gravel. When using excavated soil be sure to regularly
compact with a tamper. If your basin included a cardboard cover leave
it in place while you backll to prevent soil from falling into the basin.
The pictures used to
illustrate the installation
are of the Altum AquaBox,
but the procedures are the
same for all Blue Thumb
basins.

STEP 7
Lay the vase on its side and simply attach the
hose to the vase using the quick-disconnect
connector. The vase should be centered on
the basin as best as possible to prevent water
from blowing out on windy days. Verify that
the vase is level and is properly standing on
the grate.
STEP 8
Using the provided plastic
shims to ensure the vase is
level. The vase should never
stand uneven or unstable.
STEP 10
After the basin is properly lled and your vase is running at the
desired effect, cover the top of the basin using the Blue Thumb
Polished Pebbles to nish of the beautiful look.
If you have additional questions please visit us online at
bluethumbponds.com or call us at 888-619-3474.
STEP 9
Fill the basin with clean water and
test the fountain by plugging the
pump power cord into a nearby
electrical GFCI outlet. Water will
start owing from the fountain.
Depending on the desired effect
you may need to adjust the ow
of water.
STEP 6
Before installing the vase you
should check that the inside of
the basin is clean.
Remove any dirt that has
entered the basin using a wet/dry
vacuum.
Next, add the pump to the basin
and attach the kink-free hose
to the pump using the quick-
disconnect.
If you have a “closed-top”
vase you can adjust the
ow by turning the red
handle on the ball valve
located inside the basin on
the discharge of the pump.
If you have an “open-top”
style vase you can adjust
the ow by turning the red
handle on the ball valve
located on the standpipe
inside the vase.
Then, run the other end of the kink-free hose up through the basin to attach to
the vase in the next step.

LIMITED WARRANTY INFORMATION
All Blue Thumb basins are covered under warranty against material and
workmanship defects for a period of 5 years from the date of purchase.
The warranty is a limited warranty and will be void if the damage is the
result of improper installation or use such as, but not limited, to the
following:
• Use of the basin for anything other than its intended use as a fountain.
• Improper installation of the components
• Alteration of any kit component
• Exposure to extreme heat/freezing conditions that exceed the range of
0°F to 120°F (-15° C to 45°C)
• Exceeding the specied maximum load capacity or point load capacity
of the particular basin.
• Damage resulting from extreme weather conditions such as hurricanes,
tornadoes, earthquakes, etc.
• Damage resulting from any purposeful destruction such as vandalism.
The Blue Thumb mag-drive pumps are covered under a limited warranty
for a period of 5 years. DO NOT cut the cord of the pump- this will
void the warranty. Please see the instruction manual for details on the
warranty.
The ceramic vase is covered under a warranty against material and
workmanship defects for a period of 1 year from the date of purchase.
Damage caused by excess weather or winter conditions Is not covered
under the warranty.
The vases featured in our collection are naturally rustic, as they are
intentionally glazed unevenly, and contain variations in both color and
texture. No two pieces are alike, but all share an inherent beauty.
SEASONAL CLEANING
Every spring and fall drain the basin and replace with fresh water. Vacuum
basin if you notice excess debris that may clog your pump. If your fountain
contains an anti-splash mat cover remove any leaves and debris from it and
rinse thoroughly.
WINTERIZING FOUNTAIN
Removing your pump and storing during the winter months is the most
important step. We recommend you dissassemble and clean the pump, placing
it in a bucket of water and storing it in an area that will not freeze. This will helps
keep the seals wet and prevent the impeller from sticking.
Do not drain the basin for the winter. It is best to keep the basin lled with water
to avoid heaving during the freezing of the soil. In the spring, drain the basin
and replace with fresh water.
Move vases indoors to prevent cold weather damage. DO NOT allow water to
sit inside of a ceramic vase fountain and freeze. This will cause the fountain to
crack. NOTE: Winter damage is not covered under warranty.
If your fountain is too heavy to move we recommend covering it with a Fountain
Cover or tarp. Any cover should sufce so long as it repels the water and
doesn’t allow build up in or on the fountain.
REGULAR MAINTENANCE
Weekly- Add water to the basin as necessary. The pump needs to be
submerged at all times and not be allowed to run dry. Simply add water using
your garden hose. If you nd the water is running low frequently then reduce
the ow of the pump by adjusting the ball valve or add a splash apron around
the perimeter of the basin so that you catch & retain more of the water in
motion.
ROUTINE WATER TREATMENT
Use Blue Thumb water treatments weekly at rst and eventually bi-monthly or
monthly depending on product selection, time of season, and conditions of the
fountain.
CONTROLLING WATER LOSS & LOW WATER ISSUES
Low Water Shut-Off
This will turn the pump off once water drops below
the sensor attached to the pump preventing the
pump from overheating and causing permanent
damage.
*Keep in mind that every fountain is unique and experiences different
site conditions and water quality changes. Please contact us directly to
discuss your specic requirements or visit our website for more information
regarding the proper care of your fountain at bluethumbponds.com.
Muck
Buster
Use to remove
the build-up of
sludge in the
basin that leads
to clogging and
decreased ow
of the pump.
AquaFix
Dry
Use to spot
treat rocks
showing
signs of hairy
algae.
Fountain
Clear
Helps prevent
stains, mineral
deposits,
& organic
contaminants
from forming in
the basins and
on the fountain.
AquaFix
Liquid
Use weekly
to prevent
the build-up
of algae on
the fountain.
Fountain
Lime Buster
Safely removes
limescale and
calcium deposits
on the fountain.
Prolongs the life
of the pump by
removing limescale
build-up in and
around the pump.
Automatic Water Fill Kit - #ABDAUTO
For use with all Blue Thumb Fountain Basins