blukii Smart Key Go Mini User manual

Manual Smart Key Go Mini
16.01.2023
Made in Germany
Manual Smart Key Go Mini
Features
•Three connection modes: Open connection (convenience mode), Bluetooth
pairing (pairing mode), AES 128-bit encryption Challenge response
system (secure mode)
•Can be combined with a variety of accessories such as blukii Key-Fob,
blukii Clip or blukii Drop
•Bluetooth Low Energy® 4.2
•Setting of all parameters via blukii Configurator App
Intended Use
Smart Keys are Bluetooth transmitters that communicate with surrounding devices at certain intervals. They are used to
authenticate objects.
•This document is part of the product. It contains important information for installation and operation. Store it carefully.
•Any other use than described in these instructions is not permitted. The manufacturer assumes no liability for personal
injury or damage resulting from improper use.
•The product must not be modified
•If the product is damaged, it may no longer be used.
•Only operate the device within the technical specifications.
•The product should be operated in dry and dust-free locations.
•The product must not be exposed to strong mechanical loads.
•The Key must be protected from strong heat.
•Do not operate the device near flammable gases and vapours.
•Do not remove any stickers or labels from the product. These contain important product and safety information.
Assembly of Go Mini accessories
The Smart Key Go Mini can be used alone or in combination with numerous accessories. To install the optional accessories,
proceed as follows:
•Key Fob Go Mini:Peel off the protective strip from the double-sided adhesive tape. Insert the Smart Key with the label
facing up into the Key Fob Go Mini.
•Clip Go Mini:Peel off the protective strip from the double-sided adhesive tape. Insert the Smart Key with the label facing
upwards into the Clip Go Mini.
•Drop Go Mini:Place the Smart Key Go Mini in the ground. Put the top on slightly twisted and then turn it to the position
that the outer contour of the top and bottom part are flush.

Manual Smart Key Go Mini
16.01.2023
Made in Germany
Configuration via blukii Configurator App
Parameter changes be made directly via the blukii Configurator app. To do this, proceed as follows:
1. Place your smartphone near the corresponding Key and start the blukii Configurator app
2. Select the blukii for which you want to make changes
3. Then tap in the "Device Info" view on the blue edit button at the bottom right and wait until the connection to the Key has
been established.
4. Make the desired changes and apply them by clicking on the "Save" button
Changing batteries
To change the battery of your Smart Key Go Mini, please proceed as follows:
1. Open the battery cover and remove the battery.
2. Pay attention to the battery instructions in the next section
3. Insert the new battery with the positive pole on top. Push the battery diagonally against the side battery contact before
pushing it completely down.
4. Close the battery cover
Battery notes
•Do not use rechargeable batteries!
Rechargeable Batteries usually have a higher internal resistance and lower voltages. This can lead to incorrect runtime
estimation and reduced operating time.
•Use high quality batteries!
A Sony CR2032 button cell is suitable for operating your Smart Key Go Mini
•Risk of explosion!
oDo not recharge, short-circuit or disassemble batteries!
oImmediately remove empty batteries from the Smart Key Go Mini
oKeep batteries away from children and avoid contact with eyes, skin and mucous membranes. If you come into
contact with battery acid, wash out immediately with clear water and consult a doctor.
Help in case of errors
Error
Cause
Remedy
Smart Key is not detected in the
Configurator app
The slider for the RSSI value is too low
Raise the threshold to get more distant
Keys on the display
Smart Key is not detected in the
Configurator app
The Smart Key is out of range
Make sure that the Key is in the
immediate range of your smartphone

Manual Smart Key Go Mini
16.01.2023
Made in Germany
Technical specifications
Advertising
Beacon protocols
blukii Smart Key Protocol
Advertising interval
0,1s to 10s (adjustable)
Default: 1,9s
Radio
Standard
Bluetooth 4.2 (Bluetooth Low Energy)
Controller
Texas Instruments CC2640
Range
Up to 50m
Frequency range
2.402 to 2.480GHz
TX-Power (adjustable)
High(5dBm) / Medium(0dBm) / Low(-9dBm) / Lowest(-20dBm)
Antenna
Customized OnBoard SMD-Antenna
Encryption
Modus 1
Open connection (convenience mode)
Modus 2 (Default)
Bluetooth Pairing (Pairing Mode)
Modus 3
AES 128Bit-Verschlüsselung Challenge-Response-System
(Secure Mode)
Battery
Type
Lithium-manganese-dioxide
Model
Sony CR2032 3V/220mAh
Capacity
220mAh
Replaceable
Yes
Lifetime at Advertising interval 0,3s (TX-Power: +5dBm)
0,14 years
Lifetime at Advertising interval 1s (TX-Power: +5dBm)
0,5 years
Lifetime at Advertising interval 1,9s (TX-Power: +5dBm)
0,9 years
Mechanical specifications
Enclosure material
Copolyester
Colour
white
Protection Class
IP62
Flammability rating
UL94HB
Dimensions
22x7mm
Weight
6g
Environmental requirements
Operating temperature
-20°C to +60°C (Lifetime drops sharply under 0°C )
Certifications
CE (2014/53/EU, 2011/65/EU)

Manual Smart Key Go Mini
16.01.2023
Made in Germany
Disposal
According to European guidelines and the German Electrical and Electronic Equipment Act (ElektroG), Smart Keys must not be
disposed of with household waste.
After use, dispose of Smart Keys at a responsible collection point for old electrical and electronic devices.
Smart Keys contain batteries. These batteries must not be disposed of with household waste. Please take them to an appropriate
collection point in an unloaded state.
CE Declaration
hard&softWERK GmbH declares herewith that the device is compliant with the basic requirements and the relevant rules in
directives 2014/53/EU und 2011/65/EU.
Service
More information about your Smart Key:
Contact: https://www.blukii.com/en/contact
Further documents: https://www.blukii.com/en/resources
Phone: [phone]
Mail: [e-mail]
hard&softWERK GmbH
Bahnhofstraße 10
D-78112 St. Georgen im Schwarzwald