Extron electronics FOX II T HD 4K User manual

1
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications bef
ore connecting the
pr
oduct to the po
wer source.
FOX II T HD 4K • Setup Guide
This guide provides quick start instructions for an experienced installer to set up and operate
the Extron FOX II T HD 4K Fiber Optic Transmitter. The transmitter is compatible with all Extron
FOX II receivers.
WARNING:The FOX II T HD 4K outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use with caution.
Plug the attached dust caps into the optical transceivers when the ber cable is unplugged.
CLASS 1 LASER PRODUCT, see the FOX II T HD 4K User Guide, at www.extron.com.
AVERTISSEMENT : Le FOX II T HD 4K émet une lumière invisible en continu (conforme à la classe1) qui peut être dangereux
pour les yeux, à utiliser avec précaution. Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur lorsque
le câble bre optique est débranché.
Produit laser de classe1, voir le FOX II T HD 4K User Guide sur www.extron.com (en anglais).
Installation
Step 1 — Mounting
FOX II T HD 4K Transmitter Rear Panel
100-240V ~ 0.5A MAX
50-60 Hz
HDMI LOOP THRU
LRRS-232
OPTICAL
Tx
RESET
LINK LINK
Rx
RS-232 IR
ALARM
Tx Rx G1 2
LR
Tx Rx Tx RxG
AUDIO
INPUTS AUDIO
RETURN OUT
REMOTE
OVER
FIBER
FOX T HD 4K
Turn off or disconnect all equipment power
sources and mount the transmitter as required.
For mounting details and considerations, see the
FOX II T HD 4K User Guide at www.extron.com.
Step 2 — Input and Output Connections
a. Connect an HDMI video source to the HDMI input connector.
HDMI LOOP THRU
b. If desired, connect an HDMI video display to the Loop-Thru connector for a local display.
c. Connect an audio input device to either the Audio 3.5 mm mini jack or the Audio 5-pole captive screw connector.
LR
AUDIO
See the drawing below step 2d to make connections on the captive screw connector.
d. For optional returned audio, connect an audio output device to the Audio Return Out 5-pole captive screw connector.
LR
AUDIO
RETURN OUT
See the drawing below to make connections on the captive screw connector.
ATTENTION:
• For unbalanced audio, connect the sleeves to the
ground contact. DO NOT connect the sleeves to the
negative (–) contacts.
• Pour l’audio asymétrique, connectez les manchons au
contact au sol. Ne PAS connecter les manchons aux
contacts négatifs (–).
NOTE: For returned audio, above, you must also do the following:
• Connect an audio input device to the Audio Return In 5-pole captive screw connector on the receiver.
• Install the optional Receiver-Tx-to-transmitter-Rx cable in step 3b.
e. If you want the FOX II units to pass serial or IR data or control signals, such as for serial Rx TxGnd
Tx RxGnd
IR Device
RS-232 Device
RS-232 IR
Tx Rx Tx RxG
OVER
FIBER
control of a projector, connect the master device to the transmitter and the slave device to the
receiver via the Over Fiber 5-pole captive screw connector.
NOTE: For returned RS-232 and IR responses (from the receiver to the transmitter, you must
install the Receiver-Tx-to-transmitter-Rx cable in step 3b.
Unbalanced Stereo Output Balanced Stereo Output
Unbalanced Stereo Input Balanced Stereo Input
Do not tin the wires!
Tip
No Ground Here
No Ground Here
Tip
LR
Sleeves
Tip
Ring
Tip
Ring
LR
Sleeves
Tip
Ring
Tip
Ring
LR
Sleeves
Tip
Sleeve
Sleeve
Tip
LR

2
FOX II T HD 4K • Setup Guide (Continued)
f. For remote monitoring of the status of the Rx optical link, connect a locally constructed or obtained device to the two
RS-232 ALAR
M
Tx Rx G
12
REMOTE
rightmost Alarm poles of the Alarm and Remote RS-232 5-pole captive screw connector. The unit shorts both poles
together when no light is detected.
NOTE: The transmitter Alarm port reports the status of the link from the receiver.
g. For remote control of a unit and loading rmware, connect a host device, such as a computer or control system, to either of the
following ports:
Configuration port — The front panel mini USB connector.
CONFIG
NOTE: Extron recommends performing firmware updates via the Configuration port only.
Remote RS-232 port — The rear panel Remote RS-232 port, the 3 leftmost poles of this 5-pole captive screw connector.
RS-232 ALAR
M
Tx Rx G
12
REMOTE
The protocol for the Remote port is as follows:
• 9600 baud •no parity •8 data bits
• 1 stop bit •no ow control
Step 3 — Throughput Connections
Receiver
T
ransmitter
11
22
22
11
OPTICAL
Tx
LINK
LINK
Rx
OPTICAL
Tx
LINK
LINK
Rx
NOTE: See the two fiber cable connection drawing at right. You can connect the transmitter to a compatible receiver
in one of two ways:
• One way (transmitter to receiver) only, perform step 3a.
• Two way (transmitter to receiver and return), perform steps 3a and 3b.
a. Connect the ber between the Tx port on the transmitter and the Rx port on the receiver (1, at right).
b. If you want the receiver to return serial data (such as responses from a controlled device) to the transmitter, connect
a cable between the Tx port on the receiver and Rx port on the transmitter (2).
Tx Link and Rx Link LEDs — When lit, the link is active (light is output [Tx] or received [Rx]).
NOTE:The Link LEDs indicate transmission of light only, not whether there is data encoded in the optical link.

3
Operation
After the receiver, the transmitter, and their connected devices are powered up, the system is fully operational. If any problems are
encountered, verify that the cables are routed and connected properly and that the display device has a compatible resolution and refresh
rate. If problems persist, call the Extron S3 Sales & Technical Support Hotline. See the contact numbers on the last page of this guide for
the Extron ofce nearest you.
Indications
CONFIG SIGNAL
VIDEO AUDIO
HDCP
INPUT
RETURN OUT
SELECT
EDID
Power LED — Indicates that power is applied to the unit.
Video LEDs —
Signal LED — Lights when the unit detects an input video signal.
HDCP LED — Lights when the input signal is HDCP encrypted.
Audio LEDs —
Input LED — Lights when an analog audio or PCM digital audio signal remains above -35 dBV. The LED goes unlit if the audio signal
level drops below the threshold for 10 seconds or longer.
Return Out LED — Lights when analog audio is present on the transmitter Return Audio Output connector.
EDID
EDID Select rotary switch — Set this switch to one of the positions shown in the table below to select the source of the DDC or a specic
resolution.
Position 0 — An EDID that has previously been captured from a connected display or manually imported via an SIS command or the
Product Conguration Software.
Position 1 — The EDID is selected via the remote or USB port on the transmitter only, using an SIS command or the Extron Product
Conguration Software.
Position 2 — Use the EDID from the display connected to the receiver.
NOTE:EDID from the display connected to the receiver requires connection of both ber cables.
Position 3 — Use the EDID from the display
connected to the transmitter loop-through.
Positions 4 through E — Specify a resolution.
The table at right identies the resolutions
associated with the switch positions. All
resolutions are at 60 Hz with the exception of
4096x2160 (E), which is 30 Hz.
Position F — No EDID assigned.
Pos. Source or resolution Pos. Resolution Pos. Resolution
0 User recorded EDID 6 1366x768 C 2048x2160
1 Selected via RS-232 7 1440x900 D 2560x1600
2 Display on Rx output 8 1680x1050 E* 4096x2160
3 Display on Tx loop-through 9 1920x1080 F N/A
4 1280x720 A 1920x1200
5 1280x800 B 2048x1536
* 30 Hz

4
68-2300-50 Rev. Ax
04 15
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX [phone] FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2015 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
FOX II T HD 4K • Setup Guide (Continued)
Application Diagram
STANDBY
CLASS2 WIRING
12
XPA1002
LEVEL
1
1212
LIMITER/
PROTECT
SIGNAL
2
INPUTS OUTPUT
REMOTE
00
VOL/MUTE
10V 50mA
100-240V 1.3A,50-60Hz
100-240V~ -.-AMAX
50-60 Hz
DISPLAYPORT
LR
RS-232
OPTICAL
Tx
RESET
LINK
LINK
Rx
RS-232 IR
ALARM
Tx Rx G 1 2
L R
Tx Rx Tx RxG
AUDIO
OUTPUTS
AUDIO
RETURN IN
REMOTE
OVER
FIBER
FOX R DP 4K
POWER
12V
--AMAX
G
Tx Rx RTSCTS
COM1
G
TxRx
COM2
VC G
VOL RELAYS
1 2 C
12 3 4 G
DIGITALI/O
PWR OUT = 6W
eBUS
+V +S -S G
LAN
IPCP PRO 250
IR/S
SG
100-240V~ 0.5AMAX
50-60 Hz
HDMI LOOP THRU
L R
RS-232
OPTICAL
Tx
RESET
LINK
LINK
Rx
RS-232 IR
ALARM
Tx Rx G 1 2
L R
Tx Rx Tx RxG
AUDIO
INPUTS
AUDIO
RETURN OUT
REMOTE
OVER
FIBER
FOX T HD 4K
POWER
SDCARD USB
PLAY STATUS
HDMI
Downscaled
to 1080p
4K HDMI
4K Media Player
MODEL80
Extron
Extron
Help System
Off
Display
Room
Control
Off
Mute
Screen
Lighting
December15, 2013 - 7:58 AM
Audio
Control
Volume
Mute
Tuner
123
VCR
LaptopPC DVD Doc
Cam
Tuner
On
Channel
Last
Presets
More
Presets
3
2
1
6
5
4
9
8
7
Enter
0
RS-232
Ethernet
Ethernet
Audio
4K DisplayPort
Extron
SI 28
Surface-mount
Speakers
Extron
XPA 1002
Power
Amplier
4K Display
Local
Monitor Up to 30 km (18.75 miles)
Singlemode Fiber
SM Model
Audio
RS-232
Extron
FOX T HD 4K
Fiber Optic Transmitter
Extron
FOX R DP 4K
Fiber Optic Receiver
Extron
TLP Pro 72
0T
7" Table Top
TouchLink Pro
Touchpanel
TCP/IP
Network
Extron
IPCP Pro 250
IP Link Pro
Control Processor