BLVD urbn User manual

OWNER’S MANUAL
Read and understand this entire manual before using
this product! DO NOT RETURN TO STORE.
NOTE: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect exact appearance of actual product.
Specifications subject to change without notice.
Please have your product along with the 19 character product I.D. code with you
before contacting BLVD for warranty assistance and/or replacement parts.
Product I.D. Code: _____________ - ____________ - ____________
ELECTRIC SCOOTER
NOTE: The unit must be traveling at least 5 km/h (3 mph) before motor will engage.
Kick to start to at least 5 km/h (3 mph) while applying the throttle to engage motor.

11
CONTENTS
SAFETY WARNINGS
Safety Warnings.............................................................................................1-2
Before You Begin...............................................................................................3
Assembly and Set-Up.................................................................................... 4-5
Charging the Battery.........................................................................................5
Pre-Ride Checklist .............................................................................................6
Usage ..............................................................................................................7-8
Repair and Maintenance..............................................................................9-10
Troubleshooting Guide ....................................................................................11
Warranty..........................................................................................................13
Contact Information ........................................................................................15
INTRODUCTION: BLVD URBN ELECTRIC SCOOTER
THE BLVD URBN IS BASED ON THE LATEST COMMUTER SCOOTERS FOR ADULT USERS AND SHOULD
ONLY BE RIDDEN CAREFULLY AND RESPONSIBLY BY APPROPRIATELY MATURE AND RESPONSIBLE
RIDERS EXERCISING CAUTION AND RESPECTING APPLICABLE LAWS.
The BLVD URBN Scooter is part of a new generation of electric scooter mobility, making access to such technology
more useful and appropriately available for mature riders in environments which present desirable opportunities
for local travel and commutes – but which also, necessarily and importantly, can present additional levels of risk of
accident due to use around cars, pedestrians and public streets.
The BLVD URBN, therefore, is necessarily both similar to, and in many respects different from, previous scooters.
This product is not a toy for young riders! BLVD emphasizes, therefore, the importance of riders to understand
the risks associated with using literally any wheeled product around vehicle or pedestrian traffic and the specific
risks of riding an electric scooter. Bluntly put, you could get hurt and your actions could cause injury to others. You
must be cautious, alert and take reasonable precautions to minimize such risks of falls, impacts or other problems.
Generally, the BLVD URBN has longer battery life, multiple speed options (Low Mode up to 16 km/h (10 mph) and Sport
Mode up to 25 km/h (15.5 mph)), and a more efficient hub motor propulsion system which makes it more amenable to
“commute” uses. The user must be, and is, responsible for determining whether local laws permit use of the BLVD
URBN in varying circumstances (Laws surrounding the use of e-scooters on public and private property differ by
state. For regulations around the use of e-scooters in your particular state, please confirm your local laws before
purchasing. For more information visit ; QLD Transport, NSW Transport, VIC Roads, SA Transport, WA Transport,
TAS Transport, ACT Transport, and NT Transport. For updated laws on the use of e-scooters in New Zealand please
contact the New Zealand Ministry of Transport). The rider must be, and is, responsible for acting maturely, carefully,
and with respect for local rules of the road when riding, and the rider must be, and is, responsible for assessing and
minimizing effects of potentially adverse riding conditions including darkness or impaired visibility, fog, rain, snow,
hail, ice or electrical storms, which increase dangers inherent in operating any scooter. The rider must be, and is,
responsible for adjusting riding behavior and braking distance to suit the weather and traffic conditions, and also to
recognize that riding in low visibility conditions decreases your ability to see and be seen, especially on public streets
and around vehicles or pedestrians. The BLVD URBN head- and tail-lights may reduce such risks, and riders also are
encouraged to seek to enhance their visibility/conspicuity through use of higher visibility garments, lights or other
reflective materials when riding in reduced visibility circumstances. BLVD absolutely recommends that any rider wear
a proper helmet to minimize potential head injuries.
Use of the BLVD URBN scooter is recommended for mature riders -- using age 18+ (the generally recognized age of
“legal consent”) as a guide. Riders of the BLVD URBN certainly must respect and adhere to all locally applicable laws
and rules applicable to the use of such products.
WARNING: Riding a BLVD URBN does present potential risks and
caution is required. Like any riding product, a BLVD URBN has inherent hazards
associated with its use (for example, falling off or riding it into a hazardous
situation). Like any riding product, the BLVD URBN can and is intended to move
and it is therefore, of course, possible to lose control or otherwise get into
dangerous situations. Riders must recognize that if such things occur, a rider
can be seriously injured or die even when using safety equipment and other
precautions. RIDE AT YOUR OWN RISK AND USE COMMON SENSE.
WARNING: Always check and obey any local laws or
regulations which may affect the locations where the BLVD URBN may
be used. Keeping away from cars and motor vehicle traffic provides
the highest protection against risk of traffic-related injuries, of course.
For mature riders seeking to operate this product as legally permitted
for commuting applications, the increased risks presented by traffic
certainly emphasizes that the need for caution, personal responsibility
and compliance with local laws is imperative and is the rider’s
responsibility. Only use where allowed and with caution.
WARNING: PARENTAL AND ADULT RESPONSIBILITY AND
SUPERVISION IS NECESSARY TO ASSURE USE BY MATURE RIDERS:
Because products, like the BLVD URBN electric scooter, can and do present
potential hazards plainly associated with their use, it is well recognized
THE NEED FOR EXERCISE OF PARENTAL RESPONSIBILITY IN SELECTING
RIDING PRODUCTS APPROPRIATE TO THE AGE OF A CHILD, OR PARENTAL
SUPERVISION IN SITUATIONS IN WHICH CHILDREN OF VARIOUS AGES
MAY HAVE ACCESS TO THE SAME RIDING PRODUCTS, IS IMPORTANT. Not
every product is appropriate for every age or size of child, and different age
recommendations are found within this category of product which are intended
to reflect the nature of the hazards and the expected mental or physical ability,
or both, of a child to cope with the hazards.
WARNING: NOT FOR RIDERS UNDER AGE 18 OR HEAVIER THAN
100 KG (220 LB). DO NOT EXCEED THE WEIGHT LIMIT OF
100 kg (220 lb) – including backpacks and other items that might be carried.
Exceeding the weight limit could injure the rider and damage the
BLVD URBN. Rider weight alone also does not necessarily mean a person’s
size is appropriate to fit or maintain control of the BLVD URBN. Keep this

22
SAFETY WARNINGS
product away from small children and remember that this product is not a toy
and is intended for use only by persons who are, at a minimum, completely
comfortable and competent while operating the product.
BLVD recommends that children under the age of 18 not be permitted to use
this product. This recommendation is based not just on age or weight or height;
it reflects consideration of expected maturity and skills as well as physical
size. The recommended rider age of 18 years or older is only an estimate and
can be affected by the rider’s size, weight, or skills – not every rider 18 years
old or older will be suited to the product. Certainly, any rider unable to fit
comfortably on the BLVD URBN should not attempt to ride it, but a parent’s
decision to allow his or her child to ride this product should be
based on the child’s maturity, skill, and ability to follow rules. BLVD
emphasizes that adults are strongly advised not to disregard BLVD’s
recommendations or permit younger children to ride the BLVD URBN.
Keep this product away from small children and remember that it is
intended for use only by persons who are, at a minimum, completely
comfortable and competent while operating.
Persons with any mental or physical conditions that may make them susceptible
to injury, impair their physical dexterity or mental capabilities to recognize,
understand, and follow safety instructions and to be able to understand
the hazards inherent in the use of any ride-on product, should not use or be
permitted to use products inappropriate for their abilities. Persons with heart
conditions, head, back or neck ailments (or prior surgeries to these areas of the
body), or pregnant women, should be cautioned not to operate such products.
DO NOT EXCEED THE WEIGHT LIMIT OF 100 kg (220 lb). Rider weight
does not necessarily mean a person’s size is appropriate to fit or
maintain control of the BLVD URBN.
CHECK AND MAINTAIN PRODUCT CONDITIONS
Before use, check to confirm that covers and guards are in place and in
serviceable condition. Check that the brakes and lights are functioning properly,
that the front tire is inflated properly and has sufficient tread remaining and
that the rear wheel is free of flat spots from wear. The product should be
maintained and repaired in accordance with the manufacturer’s specifications,
using only the manufacturer’s authorized replacement parts, and should not be
modified from the manufacturer’s original design and configuration.
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Do not activate the throttle unless you are on the BLVD URBN and in a safe,
outdoor environment suitable for riding. The electric scooter must be
moving at least 5 km/h (3 mph) before the motor will engage. Once the
throttle is activated the BLVD URBN will move forward.
The normal powered top speed of this product will be approximately
25 km/h (15.5 mph), which can be affected by conditions, such as rider weight,
inclines and battery charge level. Avoid excessive speeds that can
be associated with downhill rides.
Maintain a hold on the handlebars at all times. Do not touch the brakes or motor
on your scooter when in use or immediately after riding, as these parts can
become very hot.
Ride defensively. Watch out for potential obstacles that could catch your wheel
or force you to swerve suddenly or lose control. Be careful to avoid pedestrians,
skaters, skateboards, scooters, bikes, children or animals who may enter your
path, and respect the rights and property of others.
The BLVD URBN is intended for use on flat, dry surfaces, such as pavement or
level ground, without loose debris, such as sand, leaves, rocks or gravel. Wet,
slick, bumpy, uneven or rough surfaces may impair traction and contribute to
possible accidents. Do not ride your product in mud, ice, puddles or water.
Watch out for potential obstacles that could catch your wheel or force you
to swerve suddenly or lose control. Avoid sharp bumps, drainage grates, and
sudden surface changes.
Do not attempt or do stunts or tricks. The BLVD URBN is not made to withstand
abuse from misuse, such as jumping, curb grinding or any other type of stunts.
Racing, stunt riding, or other maneuvers also enhance risk of loss of control, or
may cause uncontrolled rider actions or reactions.
Never allow more than one person at a time to ride the product.
Riding at night or when visibility is limited increases risks of accident or injury.
Should the BLVD URBN scooter be ridden in such conditions, use of lights
and additional measures to increase rider visibility and scooter conspicuity
are advised.
Never use near steps or swimming pools.
The BLVD URBN electric scooter can operate more quietly than other motorized
products may operate. Use care when in the vicinity of pedestrians or others who
may have difficulty hearing your approach. Use handbell (not included) to sound
warnings when appropriate.
Do not allow hands, feet, hair, body parts, clothing, or similar articles to come in
contact with moving parts or wheels while the motor is engaged.
Do not touch electric motor or brakes when in use or immediately
after riding.
Never use headphones or a cell phone to talk or text when riding.
Never ride your product while under the influence of drugs
or alcohol.
Never hitch a ride with a vehicle.
PROPER RIDING ATTIRE
Always wear proper protective equipment, such as an approved safety helmet
(with chin strap securely buckled), elbow pads, and kneepads. A helmet may be
legally required by local law or regulation in your area. A long-sleeved shirt, and
long pants are recommended. Always wear shoes and keep shoelaces tied and
out of the way of the wheels and motor. Never ride barefooted or in sandals.
USING THE CHARGER
The charger supplied with the product should be regularly examined for damage
to the cord, plug, enclosure and other parts. In the event of such damage, the
product must not be charged until the charger has been repaired or replaced.
Use only with the recommended charger.
Use caution when charging.
The charger is not a toy. Charger should be operated by an adult.
Do not operate charger near flammable materials.
Unplug charger and disconnect from product when not in use.
Always disconnect from the charger prior to wiping down and cleaning your
product with damp cloth.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE WARNINGS
FURTHER INCREASES RISK OF SERIOUS INJURY. USE AT YOUR OWN
RISK AND WITH APPROPRIATE AND SERIOUS ATTENTION TO SAFE
OPERATION. USE CAUTION.

Charger
(Note: Charger design may
vary from one shown)
3
Need Help? Visit our website for product support, a list of authorized service centers and customer service contact information at
www.blvdscooters.com. Please have the product I.D. code (located on the white label of your product) available for better assistance.
Additional Customer Service contact information is listed at the back of this manual.
3
BEFORE YOU BEGIN
Remove contents from box. Remove the separators that protect the components from damage during shipping.
Inspect the contents of the box for scratches in the paint, dents that may have occurred during shipping. Because
your scooter was partially assembled and packed at the factory, there should not be any problems, even if the box
has a few scars or dents.
MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY ASSEMBLY OR
MAINTENANCE PROCEDURES.
Estimated Assembly and Set-Up Time
BLVD recommends assembly by an adult.
Allow up to 15 minutes for assembly, not including initial charge time.
Allow up to 8 hours for charge (see page 5 for charging information).
WARNING:
DO NOT USE NON-BLVD PARTS
WITH YOUR BLVD ELECTRIC
SCOOTER. BLVD scooters have
been built to certain BLVD design
specifications. The original
equipment supplied at the time
of sale was selected on the basis
of its compatibility with the
frame and all other parts. Certain
aftermarket components may not
be compatible. Use of non-BLVD
parts will void the warranty.
Note: Electric scooter must
be moving at least 5 km/h
(3 mph) while applying
throttle to engage motor.
Product ID Locations:
(See locations to the left)
1. Side of Deck
2. Charger
3. UPC Side of Box (Not Shown)
Box Contents:
• BLVD URBN
• Charger
• Owner’s Manual
• 4 mm Allen Wrench
• 2.5 mm Allen Wrench
• Tire Valve Adapter
Required Tools
Throttle
LED Headlight
Front Fender
Kickstand
Rear Fender
LED Tail/Brake Light
Handle Hook
1.
Folding Latch Button
Folding Latch
Brake Lever
Steer Tube
ON/OFF Switch
Headlight ON/OFF Switch
LED Battery Indicator
2.5 mm Allen Wrench
(Included)
4 mm Allen Wrench
(Included)
Tire Valve Adapter
(Included)
2.
Handle Latch

44
ASSEMBLY AND SET-UP
Attaching the Handlebars
Required Tool: 4 mm Allen Wrench (included)
Unfolding the Scooter for First Time Use
1Before inserting the handlebars
onto the Steer Tube, pull the connector
through and remove the rubber
protector. Discard rubber protector.
2Using a 4 mm Allen wrench,
remove the four (4) Allen screws and
washers from the handlebar.
3Plug in connector. Slide the stem
onto the Steer Tube. Be careful
not to pinch wire. Tighten the four
(4) handlebar screws and washers
securely with a 4 mm Allen wrench.
1 To unfold scooter, disengage the Handle Latch (A)
from the Handle Hook (B) and stow the Handle Latch
against the Steer Tube.
2 With the Steer Tube upright, secure the Folding
Latch (C) by pushing open Folding Latch up against the
Steer Tube to lock in place. Once secured, pull out on the
Folding Latch (C) to test that it’s engaged and locked.
WARNING: Keep fingers
clear of the pivoting mechanism
when folding or unfolding the
scooter. Make sure others are
standing clear.
B
C
A
Inflating the Front Tire
The front tire is inflated when shipped, but it invariably may lose some pressure between the point of manufacturing
and your purchase. Always inflate tire to the correct PSI before first time use.
Lower air pressure can result in a shorter ride time.
Periodically check front tire. Reinflate when needed.
1 Remove the valve cap and using a bicycle style tire pump equipped for a Schrader-type valve, inflate the front tire
to the correct PSI indicated on the sidewall of the tire. Replace the valve cap.
WARNING: Do not use the
electric scooter for the first time
until you have inflated the front tire
to the correct PSI. Failure to do so
may damage your electric scooter
and void your warranty.
WARNING: Do not
overinflate, as this could damage
the tire or wheel.
Note: The pressure air supplies
found at gasoline stations are
designed to inflate high-volume
automobile tires. If you decide to
use such an air supply to inflate your
electric scooter tire, first make sure
the pressure gauge is working, then
use very short bursts to inflate to
the correct PSI. If you inadvertently
overinflate the tire, release the
excess pressure immediately.

55
CHARGING THE BATTERY
Charger
(Note: Charger design may vary from
one shown)
1Plug the charger plug into wall
outlet. The light on the charger
should be green.
Note: If green light (LED) does not
turn on, try a different outlet.
2Note: Make sure power button is
in the OFF position. Plug the charger
into the charger port. The light on
the charger should turn red during
charging. The light will turn green
again when charging is complete.
Your BLVD URBN may not have a fully charged battery; therefore you must charge the battery prior
to use. Be sure to charge the battery in a clean, dry location away from direct sunlight, flames or sparks.
• Initial charge time: 8 hours.
• Recharge time: up to 8 hours, even if the light
turns green.
• Always charge the battery immediately after riding.
• Fully charge battery before storing for extended
periods of time.
• Unplug charger from the wall outlet when not in use.
• Failure to recharge battery periodically may result in a
battery that will not accept a charge.
• Make sure the power button is turned OFF when
product is not in use. If the power button is left on for
an extended period of time, the battery may reach a
stage at which it will no longer hold a charge.
• Run time: Up to 60 minutes of continuous ride time.
Run time may vary depending on riding conditions,
rider weight, climate, and/or proper maintenance.
• Constant starting and stopping may shorten ride time.
• Battery life can vary depending on proper
maintenance and usage of the product.
• Do not charge at or below 0°C (32°F).
Charger
WARNING: Use ONLY with
the recommended charger. Batteries
are only to be charged under adult
supervision. The charger is not a
toy. Always disconnect the charger
before wiping down and/or cleaning
the BLVD URBN with a damp cloth.
The charger supplied with the
BLVD URBN should be regularly
examined for damage to the cord,
plug, enclosure and other parts. In
the event of such damage, the BLVD
URBN must not be charged until it
has been repaired or replaced.
Chargers have built-in overcharge
protection to prevent battery from
being over-charged.
Note: If the charger gets warm
during regular use, this is a normal
response and is no cause for
concern. If your charger does not get
warm during use, it does not mean
that it is not working properly.
Wall outlet - Green (stand by)
Wall outlet and unit - Red (charging)
Wall outlet and unit - Green (charged)
Note: Continue charging unit even if
light turns green prior to 8 hours.
WARNING: Battery charge
can deplete over time. Periodically
recharge battery when not in use.
Model Voltage
(Nominal) Vdc
Capacity
(Nominal) Ah
Charge
Temperature Range
Operating
Temperature Range
BLVD URBN 36 7.65 0° to 40°C
32° to 104°F
-20° to 40°C
-4° to 122°F
ASSEMBLY AND SET-UP
Inflating the Rear Tire
Required Tool: Tire Valve Adapter (included)
The rear tire is inflated when shipped, but it invariably may lose some pressure between the point of manufacturing
and your purchase. Always inflate tire to the correct PSI before first time use.
Lower air pressure can result in a shorter ride time.
Periodically check front tire. Reinflate when needed.
1 Remove the valve cap and install the tire valve adapter. Using a bicycle style tire pump equipped for a Schrader-type
valve, inflate the rear tire to the correct PSI indicated on the sidewall of the tire. Remove adapter and replace the valve
cap. Store tire valve adapter for future use.
WARNING: Do not use the
electric scooter for the first time
until you have inflated the rear tire
to the correct PSI. Failure to do so
may damage your electric scooter
and void your warranty.
WARNING: Do not
overinflate, as this could damage
the tire or wheel.
Note: The pressure air supplies
found at gasoline stations are
designed to inflate high-volume
automobile tires. If you decide to
use such an air supply to inflate your
electric scooter tire, first make sure
the pressure gauge is working, then
use very short bursts to inflate to
the correct PSI. If you inadvertently
overinflate the tire, release the
excess pressure immediately.

66
PRE-RIDE CHECKLIST
Lights
Check the head- and tail-lights for proper function. When
you activate the lights (reference “How to Ride on page 7 of
this manual), the headlight and taillight should illuminate.
Brakes
Check the brake and brake lights for proper function. When
you squeeze the brake lever (on handlebar) the brakes
should provide positive braking action and tail/brake light
should illuminate. When you apply the brakes with the
throttle on/engaged, the brake cut-off switch should cut
power to the motor.
Wheels
Periodically inspect the wheels for excessive wear.
Tire
Periodically inspect the front tire for excess wear and
replace as needed. Regularly check the tire pressure and
inflate as needed.
Frame, Fork and Handlebars
Check for cracks or broken connections. Although broken
frames are rare, it is possible for an aggressive rider to run
into a curb or object and wreck, bend or break a frame. Get
in the habit of inspecting your scooter on a regular basis.
Hardware/Loose Parts
Before every ride, check all parts, such as nuts, bolts,
fasteners, etc., to ensure they are secure and assembled
correctly. There should not be any unusual rattles or sounds
from loose parts or broken components. If the product is
damaged, do not ride. Reference “Safety Warnings”
on pages 1 and 2 of this manual.
Safety Gear
Always wear proper protective equipment, such as an approved
safety helmet (with chin strap securely buckled), elbow pads,
and kneepads. A helmet may be legally required by local law or
regulation in your area. A long-sleeved shirt and long pants are
recommended. Always wear shoes and keep shoelaces tied and
out of the way of the wheels and drive system. NEVER RIDE
BAREFOOTED OR IN SANDALS.
Laws and Regulations
Always check and obey any local laws or regulations.
Insurance
Do not assume that your existing insurance policies necessarily
provide coverage for electric product use. Check with your
insurance company for information regarding insurance.
Storage
Prolonged exposure to UV rays, rain and the elements may
damage the enclosure materials, store indoors when not in use.
Need Help? Visit our website for product support, a list of authorized service centers and customer service contact information at
www.blvdscooters.com. Please have the product I.D. code (located on the white label of your product) available for better assistance.
Additional Customer Service contact information is listed at the back of this manual.

7
Need Help? Visit our website for product support, a list of authorized service centers and customer service contact information at
www.blvdscooters.com. Please have the product I.D. code (located on the white label of your product) available for better assistance.
Additional Customer Service contact information is listed at the back of this manual.
USAGE
7
How to Ride
Do not activate the thumb throttle unless you are on the BLVD URBN and in a safe, outdoor environment suitable for riding.
Put kickstand up.
Press the power button (A) for two seconds, the LEDs on the battery display will light up. Press the power button
(A) for two seconds again to turn the unit off.
Headlight and Taillight: To activate the headlight and taillight the product must be powered ON. Press the power
button (A) once to activate the headlight and taillight. To deactivate the headlight and taillight, press the power
button once again.
Get on the scooter and place both hands on the handlebars. Kick to start (B), and then press down on the thumb
throttle (C).
How to Stop
For controlled stops, apply the brake by pressure on the rear-fender brake or electronic brake (on handlebar).
BLVD recommends that you practice applying the brake options at various speeds and in an open area free from
obstructions before riding your scooter around others.
When the brake is applied the tail/brake light will glow brighter. The brake light is always functional and
independent of the other lights being activated.
Option 1 - Press the electronic brake (on handlebar), the power will cut off and then product will slow to a stop.
Option 2 - Step on the rear-fender brake, the power will cut off and then product will slow to a stop.
Note: The BLVD URBN electric scooter features Regenerative Braking. Regenerative braking is a means of
recovering and converting kinetic energy into stored power. Using the scooter’s electric motor, energy that is usually
lost during deceleration and braking is captured and converted back to stored power extending run time and range.
Regenerative braking only recovers a small amount of energy at a time but can be significant over the course of a full
battery cycle. As always specifications and the amount of recovered regeneration varies with rider weight, terrain,
and environmental conditions.
Note: Electric scooter must
be moving at least 5 km/h
(3 mph) while engaging
throttle to engage motor.
Speed Mode
Power Button
Light
Battery
Capacity
Speed
C
A
B
WARNING: The brakes are
capable of skidding the rear tire
and throwing an unsuspecting rider.
Practice in an open area free from
obstacles until you are familiar with
the brake function. Avoid skidding to
a stop as this can cause you to lose
control and/or damage the rear tire.
Note: As an additional safety
feature, the scooter is designed to
cut power to the motor when the
brakes are applied.
Note: Motor will re-engage,
(without having to kick to start), if
brakes are released and throttle is
applied before scooter has slowed
down to under 5 km/h (3 mph).
Note: Practice riding only in wide
open areas clear from curbs,
parking blocks and other obstacles.
Impacting the wheels against
any hard surface can damage the
wheels. Wheels are not covered
under the limited warranty.OPTION 2OPTION 1

88
USAGE
WARNING: Keep fingers clear
of the pivoting mechanism when
folding or unfolding the scooter.
Make sure others are standing clear.
Changing the Speed Mode
There are two modes for speed. The BLVD URBN is set on the Sport 25 km/h (15.5 mph) speed setting at the factory.
Press power button twice quickly to select the speed mode.
Folding Scooter
1The Sport mode max speed is up
to 25 km/h (15.5 mph) as shown by
an “S” at the top of the display .
2 The Low mode max speed is
up to 16 km/h (10 mph) .
B
ADC
1 To fold scooter, press and hold down the
Folding Latch Button (A) while pulling the Folding
Latch (B) open.
2 To use the Steer Tube as a carrying handle, deploy
the Handle Latch (C) and engage the Handle Hook (D)
on the frame.
Note: The BLVD URBN display
setting at the factory is in miles.
If you would like to change
the display to reflect kilometers,
press the power button quickly
three (3) times to select the
desired mode.

9
REPAIR AND MAINTENANCE
9
Adjusting the Folding Mechanism
Required Tool: 2.5 mm Allen Wrench (included)
1 Fold scooter according to folding scooter
instructions on page 8. Using a 2.5 mm Allen wrench,
loosen screw A. Using a 2.5 mm Allen wrench adjust
screw B.
2 Tighten screw Aand unfold to complete adjustment.
Turn power switch “OFF” before beginning repair or maintenance:
• Read the instructions
• Remove charger plug
• Turn the power off
• Secure the product under repair
• Exercise caution around
exposed parts
• Contact BLVD customer service
if unsure about any repair or
maintenance
• Repair and maintenance should
be performed by an adult only
A
B
A

1010
REPAIR AND MAINTENANCE
WARNING: Risk of fire - no user serviceable parts.
Cleaning Your Scooter
Wipe with a damp cloth to remove dirt and dust. Do not use industrial cleaners or solvents as they may damage the
surfaces. Do not use alcohol, alcohol-based or ammonia-based cleaners as they may damage or dissolve the plastic
components or soften the decals or decal adhesive.
Battery Care and Disposal
Do not store in freezing or below freezing temperatures. To properly maintain your battery and ensure maximum
battery life, carefully read the “Charging the Battery” section on page 5 of this owner’s manual.
Recycling Lithium-ion
Batteries: Lithium-ion batteries are
recyclable. You can help preserve
our environment by returning your
used rechargeable batteries to the
collection and recycling location
nearest you.
Caution: Do not handle damaged
lithium-ion batteries.
CONTAINS LITHIUM-ION BATTERY PACK. BATTERIES MUST BE RECYCLED.
Disposal: Your electric scooter uses a lithium-ion battery pack which must be recycled or disposed of in an
environmentally safe manner. Do not dispose of a battery pack in a fire. The battery pack may explode.
Do not dispose of a battery pack in your regular household trash. The incineration, land filling or mixing of batteries
with household trash is prohibited by law in most areas. Return exhausted batteries to a federal or state approved
lithium-ion battery recycler.
Charger
The charger supplied with the electric scooter should be regularly examined for damage to the cord, plug,
enclosure and other parts and in the event of such damage, the product must not be charged until it has been
repaired or replaced.
Use ONLY with the recommended charger.
Not intended for use at elevations greater than 2000 m above sea level.
Wheels
Wheels and drive system are subject to normal wear and tear. It is the responsibility of the user to periodically
inspect wheels for excess wear and replace hub motor components as required.
Need Help? Visit our website for product support, a list of authorized service centers and customer service contact information at
www.blvdscooters.com. Please have the product I.D. code (located on the white label of your product) available for better assistance.
Additional Customer Service contact information is listed at the back of this manual.

11
Need Help? Visit our website for product support, a list of authorized service centers and customer service contact information at
www.blvdscooters.com. Please have the product I.D. code (located on the white label of your product) available for better assistance.
Additional Customer Service contact information is listed at the back of this manual.
11
TROUBLESHOOTING GUIDE
Problem Possible Cause Solution
Does not work out of the box Unit must be traveling at least 5 km/h (3
mph) before motor will engage
Undercharged battery
Kick to start to at least 5 km/h (3 mph) while engaging throttle to
engage motor.
Check lights on charger:
Plugged into wall - Green
Plugged into wall & unit - Red (charging)
Plugged into wall & unit - Green (charging complete)
No lights/Blinking lights - Replace charger
No longer works No lights on charger
Undercharged battery
Battery will not hold a charge
Check power to wall outlet and/or try a different outlet.
Check lights on charger:
Plugged into wall - Green
Plugged into wall & unit - Red (charging)
Plugged into wall & unit - Green (charging complete)
No lights/Blinking lights - Replace charger
Replace battery.
Short run time/runs slow Rider’s weight
Riding conditions
Battery not fully charged
Old/damaged battery
Do not exceed 100 kg (220 lb.) maximum weight limit.
Use only on flat, dry surfaces. Avoid inclines and areas with
heavy debris.
Charge product - refer to page 5 for charging information.
Replace battery.
Charge battery at least once a month when not in use.
For more troubleshooting tips, a list of available replacement parts or to locate an authorized Service Center in your area,
visit our website at www.blvdscooters.com or call toll free 1800 956 630 (AU) / 0800 003 221 (NZ) to speak to a live Customer Service Representative.
*Product(s) should be turned OFF and fully charged prior to doing any Troubleshooting.
NOTE: All troubleshooting steps should be performed by an adult only.

1313
WARRANTY
BLVD Limited Warranty
The manufacturer warranties this product to be free of manufacturing
defects for a period of 12 months from date of purchase. This Limited
Warranty does not cover normal wear and tear, tire, tube or cables, or any
damage, failure or loss caused by improper assembly, maintenance, storage
or use of the BLVD URBN.
This Limited Warranty will be void if the product is ever:
• used in a manner other than for recreation or transportation;
• modified in any way;
• rented.
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
BLVD does not offer an extended warranty. If you have purchased an
extended warranty, it must be honored by the store at which it was
purchased.
For your records, save your original sales receipt with this manual and write
the serial number below.
__________________________________________
WARNING: Changes or modifications to this unit not expressly approved by BLVD, could void the user’s authority to operate the equipment.

NOTICE: INSURANCE
YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR
ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC
RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED,
YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.

1515
CUSTOMER SERVICE CONTACT INFORMATION
Need Help? Visit our website for product support, a list of authorized service centers and customer service contact information at
www.blvdscooters.com. Please have the product I.D. code (located on the white label of your product) available for better assistance.
Additional Customer Service contact information is listed below:
BLVD Scooters c/o The Brand Exchange Pty Ltd
401 Riversdale Road
Hawthorn East
VIC 3123
1800 956 630 (AU) / 0800 003 221 (NZ)
www.blvdscooters.com
[e-mail]
Printed in China for The Brand Exchange Pty Ltd.
Copyright © 2021. 2020 BLVD and the BLVD logo design are trademarks of The Brand Exchange Pty Ltd.
US_210915