Bock Water heaters 100PDVI-250-XA 225 User manual

Power Direct Vent
Independent Vent System
Gas Water Heaters
80 to 100 gallons/150,000 to 250,000 BTU
PVC Independent vent
Sealed combustion
Low NOx construction available
Electronic ignition and controls
Non-CFC foam insulation
Automatic blower motor
Glass-lined storage tank
Hand hole cleanout
Sediment reduction system
Standard and ASME construction
NSF kit available
Complies with SCAQMD low NOx requirements
Design certified by CSA International (formerly AGA/CGA)
3-Year Limited Tank/1-Year Limited Parts Warranties
Energy Saver
80% Thermal Efficient

www.bockwaterheaters.com
110 South Dickinson Street , Madison, Wisconsin 53703
Toll Free 800.794.2491 • Phone [phone] ● Fax [phone]
80029 Rev 6/08
Natural Gas use the sux "NA", Example: 80PDVI-150-NA
LP on 80PDVI-250 and 100PDVI-250 only. Use sux "XA" to order. Example: 80PDVI-150-XA
ASME Construction available on the 80PDVI-250 and 100PDVI-250 only; Use sux "A" to order; Example: 80PDVI-250-NA-A
For Low NOx compliance to meet SCAQMD requirements, place an "LN" in the model number; Example: 80PDVILN-250-NA
T=Top, F=Front, R=Rear
These models meet or exceed theThermal Eciency and Standby Loss Requirements of ASHRAE 90.1b current standard.
115V A.C. Required
T&P Valve, Brass Drain Valve, Dielectric Fittings, Magnesium Anode Rods: Factory Installed
Pressures (all): Working Pressure, 150 psi; Tested Pressure, 300 psi
Warning: Installation should be in accordance with all national and/or local codes. In the absence of local codes, refer to NFPA 54 or ANSI Z21.10.1.
Caution: The recommended maximum hot water termperature setting for normal residential use is 120°F. Bock recommends a tempering valve or anti-scald
valve be installed and used according to the manufacturer’s directions to prevent scalding.
Energy Saver
Power Direct Vent
Independent Vent System
Gas Water Heaters
This product is available from:
MODEL
NUMBER
STORAGE
(GAL)
RATED
INPUT
(BTU/HR)
1ST HR
DEL GAL
@ 100°F
RISE
RECOVERY GPH
@ DEGREE RISE
DIMENSIONS (INCHES) SHIPPING WEIGHT
A
HEIGHT
B
DIA.
C
TOP
WATER
CONN.
D
F&R
HOT
CONN.
E
F&R
COLD
CONN.
F
GAS
CONN.
G
TOP
VENT
HEIGHT
WATER
CONN.
GAS
CONN.
DIA.
RELIEF
VALVE
OPEN.
STD
(LBS)
ASME
(LBS)40°F 100° F 140° F
80PDVI-150 80 150,000 204 364 145 104 63-1/2 28-1/4 65-1/8 51-5/16 20-3/16 17-1/4 68-3/16 1-1/12(T&F)
2(R) 3/4 3/4 645 N/A
80PDVI-200 80 199,999 253 485 194 139 63-1/2 28-1/4 65-1/8 51-5/16 20-3/16 17-1/4 68-3/16 1-1/12(T&F)
2(R) 3/4 3/4 645 N/A
80PDVI-250 83 250,000 301 606 242 173 63-1/2 28-1/4 65-1/8 51-5/16 20-3/16 17-1/4 73-1/16 1-1/12(T&F)
2(R) 3/4 1 645 720
100PDVI-150 100 150,000 219 364 145 104 74-1/8 28-1/4 74-1/8 60-5/16 20-11/16 17-1/4 77-3/16 1-1/12(T&F)
2(R) 3/4 3/4 735 N/A
100PDVI-200 100 199,999 266 485 194 139 74-1/8 28-1/4 74-1/8 60-5/16 20-11/16 17-1/4 77-3/16 1-1/12(T&F)
2(R) 3/4 3/4 735 N/A
100-PDVI-250 100 250,000 312 606 242 173 74-1/8 28-1/4 74-1/8 60-5/16 20-11/16 17-1/4 82-1/16 1-1/12(T&F)
2(R) 3/4 1 735 815
Propane Gas Inputs (LP) 1ST HR.
DEL GAL.
@ 100° F
RISE
RECOVERY GPH @
DEGREE RISE
40° F 100° F 140° F
80PDVI-250-XA 225,000 BTUH 274 545 218 156
100PDVI-250-XA 225,000 BTUH 288 545 218 156
(LN) LowNOx Burners 1ST HR.
DEL GAL.
@ 100° F
RISE
RECOVERY GPH @
DEGREE RISE
40° F 100° F 140° F
80PDVILN-150 150,000 BTUH 201 364 145 104
80PDVILN-200 180,000 BTUH 250 436 175 125
80PDVILN-250 220,000 BTUH 298 533 213 152
100PDVILN-150 150,000 BTUH 215 364 145 104
100PDVILN-200 180,000 BTUH 245 436 175 125
100PDVILN-250 220,000 BTUH 283 533 213 152
ACGD
E
B
F