bodhi 5059413795015 User manual

IMPORTANT: PUT ALL SCREWS INTO PLACE BEFORE TIGHTENING EACH ONE GRADUALLY IN SEQUENCE.
THIS IS IMPORTANT TO ENSURE THAT ALL THE BOLTS LINE UP CORRECTLY TO START WITH
ASSEMBLY & PRODUCT CARE
DINING TABLE 2060/2660x1000x740MM
5059413795015
Thank you for purchasing this PRODUCT. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product
You will need Allen Key (included)
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the retailer from
whom you bought this product.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE
CARE WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 15 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.

IMPORTANT: PUT ALL SCREWS INTO PLACE BEFORE TIGHTENING EACH ONE GRADUALLY IN SEQUENCE.
THIS IS IMPORTANT TO ENSURE THAT ALL THE BOLTS LINE UP CORRECTLY TO START WITH
Read this leaflet in full before commencing assembly.
Fittings and parts checklist
Part
Description
Image
Qty
A
Leg
2
B
Table Top
1
C
Middle Table Top
1
D
M6x10mm Allen Bolt
12
E
M6 Washer
12
F
M6 Allen Key
1

IMPORTANT: PUT ALL SCREWS INTO PLACE BEFORE TIGHTENING EACH ONE GRADUALLY IN SEQUENCE.
THIS IS IMPORTANT TO ENSURE THAT ALL THE BOLTS LINE UP CORRECTLY TO START WITH
Step by step assembly instructions
Step One
Place the Table Top (B) on a flat surface, insert the Legs (A) into the holes provided at the four
corners of the tabletop.
IMPORTANT: We would advise that at this stage the top remains inside the original packaging, or
lay onto a clean carpet or banket to avoid damage to the surface.
Step Two
With the Table Top (B) upside down, using Washer (E) and Bolt (D), fix the Legs (A) into the bolt
holes provided with Allen Key (F), hand tight.
IMPORTANT: We would advise that at this stage the top remains inside the original packaging, or
lay onto a clean carpet or banket to avoid damage to the surface.

IMPORTANT: PUT ALL SCREWS INTO PLACE BEFORE TIGHTENING EACH ONE GRADUALLY IN SEQUENCE.
THIS IS IMPORTANT TO ENSURE THAT ALL THE BOLTS LINE UP CORRECTLY TO START WITH
Step Three
Carefully lift and stand product in upright position.
Step Four
Push the Table Top (B) in arrow direction to leave enough space for the Middle Table Top (C).
Step Five
Put the Middle Table Top (C) in between the Table Top (B) (as shown in below picture on the left).
Pull the Table Top (B) inward to be together with the Middle Table Top (C). Make sure the position
is correct.

IMPORTANT: PUT ALL SCREWS INTO PLACE BEFORE TIGHTENING EACH ONE GRADUALLY IN SEQUENCE.
THIS IS IMPORTANT TO ENSURE THAT ALL THE BOLTS LINE UP CORRECTLY TO START WITH
Step Six
Pull the Table Top (B) inward from both sides. Lock the buckle underneath the Table Top (B).
Finish.

IMPORTANT: PUT ALL SCREWS INTO PLACE BEFORE TIGHTENING EACH ONE GRADUALLY IN SEQUENCE.
THIS IS IMPORTANT TO ENSURE THAT ALL THE BOLTS LINE UP CORRECTLY TO START WITH
OUTDOOR FURNITURE
Thank you for purchase, we hope you enjoy your furniture for the upcoming summer and years to
come. Below are a few points about your furniture, please read and retain for future reference.
Safety Instructions
Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a
competent person. No liability will be accepted for damage or injury caused by incorrectly insalled
or assembled furniture.
Moving Furniture:
Never drag furniture when moving it, always lift it.
When lifting or moving a table always do so from under frame and not the table top.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage
or injury.
It is recommended that before moving heavy objects to a new location they are completely dis-
assembled to avoid personal injury or damage to the furniture. Please be careful to retain all
fittings when doing this.
Load Caution:
Never overload an item such as a shelf that may be beyond what the shelf is reasonably expected
to hold.
Please do not sit or place an amount of weight onto the edge of a tabletop as this may cause the
table to topple.
Single Chairs/Arm Chairs are designed for sitting one person only. Sit whilst supporting your back
only at a resting position. If any parts are missing or damaged, please stop using Chair until parts
are replaced. WARNING: DO NOT USE CHAIRS TO STAND ON. DO NOT ROCK OR TOPPLE
CHAIR BACKWARDS.
Treatment:
We recommend that when applying oil, mineral spirits, or bleach, gloves and safety goggles are
worn.

IMPORTANT: PUT ALL SCREWS INTO PLACE BEFORE TIGHTENING EACH ONE GRADUALLY IN SEQUENCE.
THIS IS IMPORTANT TO ENSURE THAT ALL THE BOLTS LINE UP CORRECTLY TO START WITH
Care and Maintenance
WHEN CARED FOR PROPERLY, THIS HAND CRAFTED FURNITURE WILL PROVIDE YOU
WITH YEARS OF ENJOYMENT AT YOUR HOME.
If your furniture requires assembly, put all screws into place before tightening each one gradually
in sequence. This is important to ensure that all the bolts line up correctly to start with.
The frame of the furniture is all-weather proof. However, although cushions are showerproof, you
will need to store your cushions away when not in use to keep them at their best. They can be
sponge cleaned with a gentle detergent. Avoid machine washing as this may affect the Fire
Retardant coating.
We recommend using a parasol over dining sets on sunny days to protect from direct sunlight. In
Windy conditions don’t forget to store your furniture away especially a parasol.
Glass
If your furniture includes glass, please note that it is tempered glass. This is a toughened safety
glass so in case of an accident it crumbles to a safe shape rather than breaking into dangerous
shards.
Be aware that if a liquid is on the glass to mop it up immediately, because when it is in direct
sunlight it can act as a magnifier and can cause the frame under the Glass to melt, especially
Rattan.
When moving your furniture ensure that it is carried and not dragged as this weakens the glass. If
you remove the glass, lay it flat onto a soft protective surface like a blanket, rather than upright to
avoid chipping, and always onto a soft protective blanket.
REMEMBER:
1. Do not use the glass as a chopping surface. Do not strike the glass with hard or pointed objects.
2. Do not sit or stand on horizontal glass surfaces.
3. Do not place very hot or very cold items against or in close proximity to glass surface(s).
4. The surface should be protected with coasters, trivets or placemats.
5. All spills should be blotted up immediately. Do not wipe the spill or this may spread it. Clean the
surface with a clean soft cloth (non-abrasive) and mild detergent or stone soap.

IMPORTANT: PUT ALL SCREWS INTO PLACE BEFORE TIGHTENING EACH ONE GRADUALLY IN SEQUENCE.
THIS IS IMPORTANT TO ENSURE THAT ALL THE BOLTS LINE UP CORRECTLY TO START WITH
Metal (Outdoor)
Metal furniture is weatherproof powder coated paint which requires minimal maintenance:
Cleaning your metal furniture is very simple. Use a soft cotton cloth and clean with mild detergent
or water, using a towel immediately dry the furniture afterwards.
Due to the outdoor nature of these products, some rusting is to be expected. This is the natural
aging process of these products. Metal furniture is usually damaged due to rust, as a precaution a
soft wax after cleaning will help seal it.
If it has a few spots of rust, you can treat it with rust remover, following the manufacturers
guidelines. (some finishes are made to look like rust)
Smudges and smears can be removed from metal furniture by using a window cleaner and a
paper towel.
Rattan
If product has Rattan, you may find that the end of the weave has become loose, this isn’t a
manufacturing error it is the end of the weave and simply needs to be tucked back into place. Your
product has been individually woven by hand therefore a uniform appearance is unlikely, a slant to
the weave is common with a rattan item especially with different tones of weave.
Rope
If product includes rope, you may find that the end of the weave has become loose, this isn’t a
manufacturing error it is the end of the weave and simply needs to be tucked back into place. Your
product has been individually woven by hand therefore a uniform appearance is unlikely, a slant to
the weave is common with a rope item especially with different tones of weave.
General Wood, unpainted (Outdoor)
Never use sharp items on the surface of the product. For example knives and utensils may
damage the product. Make sure all surfaces are protected from heat and liquids by mats and
coasters. Wipe up spills immediately and ensure that a mat or pad is placed under paper if you are
writing.
Extendable dining tables should be left extended for the first few months to avoid an uneven
appearance.

IMPORTANT: PUT ALL SCREWS INTO PLACE BEFORE TIGHTENING EACH ONE GRADUALLY IN SEQUENCE.
THIS IS IMPORTANT TO ENSURE THAT ALL THE BOLTS LINE UP CORRECTLY TO START WITH
Furniture with a hard lacquer, wax polish or painted surface should be dusted with a dry cloth.
Waxed furniture will need to be given a coat of beeswax a couple of times a year to help maintain
its luster.
Spray polishes are best avoided as they contain silicones which may spoil the furniture’s surface
by building up over time.
Painted Wood (Outdoor)
Never use sharp items on the surface of the product. For example knives and utensils may
damage the product. Make sure all surfaces are protected from heat and liquids by mats and
coasters. Wipe up spills immediately and ensure that a mat or pad is placed under paper if you are
writing.
Extendable dining tables should be left extended for the first few months to avoid an uneven
appearance.
Hand painted brush stroke finish's will hold up to everyday wear and tear quite nicely. However, it
is important to remember that your piece is still a wood piece of furniture and should be cared for
as such.
Painted furniture still requires regular dusting with a damp cloth. When very soiled wash with a
solution of mild, non-abrasive detergent and warm water. Wring a cloth nearly dry and work on a
small section at a time, then rinse with clear water drying after.
Never leave water to settle on the surface as this will cause damage. Any liquid spilled onto the
item should be cleaned up immediately using an absorbent cloth.
AVOID chemical cleaners or liquid furniture polish including direct contact with greasy substances.
As with all natural wood products, there will be some movement within the parts as the furniture
acclimatises to its surroundings, you may see slight chipping and cracks where panels meet, this is
a completely natural occurrence with ALL painted products using natural solid timbers.
Painted surfaces can be carefully touched up with matching paint.
There will be various brush lines, slubs, and little inconsistencies in the painted finish, this is all
part of the relaxed handfinished look and feel of hand painted collections.
WHEN CARED FOR PROPERLY, THIS HAND CRAFTED FURNITURE WILL PROVIDE YOU
WITH YEARS OF ENJOYMENT AT YOUR HOME.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE