BOERPLAY SOLE030.140 User manual

SOLE030.140
Revolving plate

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 140 B
Instapduizel
8-8-2016
BOER
SPEELTOESTELLEN
Afmetingen Dimensions
0,00 m
0,13 m
1,15 m
0,48 mØ

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 140 B
Instapduizel
8-8-2016
BOER
SPEELTOESTELLEN
Obstakelvrije zone Obstacle free zone
Obstakelvrije zone
Obstacle free zone
Opvangzone
Impact area
3,48 m
1,50 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 140 B
Instapduizel
8-8-2016
BOER
SPEELTOESTELLEN
Bodemplan Groundplan
0,64 m
0,72m
1,42 m 1,42 m
0,64m1,42m
1,42m
Grondmarkering
Ground level marker
0,42m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 140 B
Instapduizel
8-8-2016
BOER
SPEELTOESTELLEN
Modules Modules
OpmerkingBenamingRev.Bew.VolgnrProgr.Type
#
Nr
245 kiloPoermodel 7 002007OBTMO
11
Instapduizelraaideel
B
002010ROTMO
1
2
uizelAnker
C003070ROTMO13
2
3
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoo dmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven speci iek de maten van de verbindingen aan
- De modules met buizen zijn op de tekeningen bemaat op bovenkant kopplaat
- Overige modules zijn bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 - Graa de gaten volgens het bodemplan
2 - Plaats 1
3 - Plaats 3 en verbind deze aan 1
4 - Plaats 2 en verbind deze aan 3
5 - Controleer o het toestel voldoet aan de a metingen zoals op blad 'a metingen'
6 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Controleer de a metingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions o the posts and loors
- The detailed dimensions show the speci ic dimensions o the connections
- The modules which contain tubes are dimensioned at the top o the langes
- Other modules are dimensioned at the top (climbing walls, caps or the posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Place 1
3 - Place 3 and attach it to 1
4 - Place 2 and attach it to 3
4 - Check that the equipment con orms to the dimensions shown on sheet 'dimensions'
5 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the asteners
2 - Check the dimensions o the sa ety area with regard to the play equipment
1
Typeplaatje
Identification plate
B

LOGBOOK
(Onderstaand logboek kan gebruikt worden om te voldoen aan de eisen, gesteld in artikel 14 van het Warenwetbesluit Attractie- en Speeltoestellen)
Type indication Pioneer Play
Product code SOLE030.140
Name of equipment Instapduizel
Maximum height of fall 0,2 m
Year of construction 2017
Certificate 09100312653
inspection authority Liftinstituut B.V.
Buikslotermeerplein 381, A'dam - 1025 XE Amsterdam
Name manufacturer BOERplay
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
name installer
Description of equipment Revolving plate
Location of equipment
Data about the owner of the play equipment
Name:
Address:
Postcode and town:
Contact person:
Telephone number:
Data about the administrator of the play equipment
Name:
Address:
Postcode and town:
Contact person:
Telephone number:
SOLE030.140
Revolving plate

LOGBOOK
Inspection and maintenance intervals
Nr.
Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and missing parts.
Inspect bolts, screws and nuts for absence, jams, corrosion
and wear.
Add missing parts, secure joints, apply missing fixing
agent and replace corroded parts.
1
2
Chec suspension for wear. Replace worn parts and/or remove non-functioning
parts.
1
3
Inspect rotating parts such as hinges, rolling-element
bearings, etc. for wear and acceptability.
Replace worn parts and/or remove non-functioning
parts.
1
4
Chec wood for splinters, unacceptable damage and signs of
rot. Especially at ground level.
Repair damage. Replace affected wood. Smoothen
splintered wood and sharp edges.
1
5
Inspect foundation for stability, tearing and coverage. Restore foundation and covering material.
3
6
Examine rubber and synthetic parts for wear, damage and
brea . Replace original parts.
3
7
Inspect metal for corrosion and damage in the coating. Restore any damaged coating (after removing rust and
applying primer).
6
Chec ropes, cables, chains and nets for wear and damage.
Steel cables and nets which are tensioned must be chec ed
for tension.
Replace parts where necessary. Steel cables and nets
must be tensioned.
3
9
Inspect equipment for unsafe changes and additions. Remove unsafe additions and correct unsafe changes.
1
10
Inspect safety surfaces. Restore and repair where necessary.
1
Remarks
1. If used intensively, all points require extra attention.
2. Extreme weather conditions and locations may require a higher inspection frequency. Discuss this with
the supplier.
3. Vandalism-sensitive locations require stricter inspections, possibly daily.
4. Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly.
Examples are poisonous plants, glass shards, etc. Frequency depends on strain.
5. Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area.
6. Replacement parts can be ordered at the manufacturer with the part numbers on the module drawing.
Drawings can be found in de user guide.
7. The impact area shall be provided with impact attenuating surface according to the specified falling
height.
. This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7".

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD OBT 007 002
Poermodel 7
245 kilo
13-2-2014
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
OpmerkingBenamingRev.Bew.VolgnrProgr.Type
#
Nr
M16 - VZ 8.8Zeskantmoer 015016017BSV
41
M16 x 50 - VZ 8.8arrosseriering 050016035BSV
4
2
245 kgPoermodel 7
245007POEOBT13
3
2
1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD ROT 010 002 B
Draaideel
Instapduizel
8-8-2016
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#Nr
3,5 x 19 - RVS A2-70
elfb. schroef
019004005BSR12
1
M10 - RVS A2-70
Borgmoer
010010010BSR62
BORG RVS M10DOPMOER 020010011BSR63
M10 x 60 - RVS A2-70
Verzonken bout
060010024BSR124
M10SLUITRING 002010030BSR65
M10 x 30 x 2,5CARROSSERIERING 030010035BSR66
BlauwTelbol helft
050036BOLKST2
7
Rood
Telbol helft
030036BOLKST28
Geel
Telbol helft
010036BOLKST29
Donut RoodBeschermdop M10-M12
030010DONKST610
6 MM ROODOPVULDOPJE 030006DOPKST6
11
Dop roodBeschermdop M10-M12
030010DOPKST612
Instapduizel
Platform
DRBM
003ROTOHO
1
13
DraaischijfAfwerk plaat
051025ROTOPE
114
InstapduizelGripbeugel
A
320027ROTSME115
4 10 52 12
1
9
15
7
8
13
14
4
11
6
3

Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
M10 x 16 - RVS A2-70
Bolkopbout ISO 7380
016010023BSR21
55 x 2,00 - VZ 8.8
Ci clip DIN 471
002055041BSV12
Ø75 x Ø55 x 10
Oliekee ing
055075OKRKST13
DuizelankeAfstandbus
009ROTKST
14
Duizel
Stop PA6010ROTKST1
5
6009 2RSR - 75x45Kogellage 6009 075045KOGLAG26
DuizelAnke
B
905046ROTSME
17
Duizel
As
C304047ROTSME18
Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD ROT 070 003 C
Anke
Duizel
28-11-2016
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
7
6
4
6
3
2
5
8
1