BOERPLAY Tumble bars Trio H1.45-1.20-1.00 User manual

Tumble bars Trio H1.45-1.20-1.00
BBPE040.4B
Powered by TCPDF (www.tcpdf.org) 1 / 1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 040 4B
Duikel trio
Boer Basic play ZO
15-7-2019
BOER
SPEELTOESTELLEN
Hoofdafmetingen Main dimensions
0,00 m
1,00 m
1,20 m
1,27 m
1,45 m
1,82 m
0,00 m
0,05 m
0,10 m
Typeplaatje
Identification plate
B

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 040 4B
Duikel trio
Boer Basic play ZO
15-7-2019
BOER
SPEELTOESTELLEN
Obstakelvrije zone Obstacle free zone
Obstakelvrij WAS
Obstacle free WAS
Opvangzone
Impact area
Obstakelvrij EN-11 6
Obstacle free EN-1176
3,49 m
3,00 m
5,42 m
R1,50m
R1,50m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 040 4B
Duikel trio
Boer Basic play ZO
15-7-2019
BOER
SPEELTOESTELLEN
Bodemplan Groundplan
0,50 m
Grondmarkering
Ground le el marker
1,50 m 1,50 m
0,25 m o
0,55 m 0,80 m 0,80 m 0,80 m 0,55 m
5,42 m
R1,50m
R1,50m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 040 4B
Duikel trio
Boer Basic play ZO
15-7-2019
BOER
SPEELTOESTELLEN
Modules Modules
OpmerkingBenamingRevBew.VolgnProgrType#Nr
Boer Basic playRailing
AA
009
BBP
MOD
1
Boer Basic play ZOAanbouwduikel 1,1 m
AB
024
BBP
MOD22
Boer Basics ZO
Staander 0,95m los
B
047
BBP
MOD2
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoofdmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven specifiek de maten van de verbindingen aan
- De modules met buizen zijn op de tekeningen bemaat op bovenkant
kopplaat
- Overige modules zijn bemaat op de bovenkant (klimwanden,
paalkappen, etc.)
Montagevolgorde:
1 - Graaf de gaten volgens het bodemplan
2 - Plaats twee keer 2 en twee keer 3
3 - Plaats drie keer 1, verbind deze aan 2 en 3
4 - Controleer of het toestel voldoet aan de afmetingen zoals op blad
'afmetingen'
5 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions of the posts and floors
- The detailed dimensions show the specific dimensions of the connections
- The modules which contain tubes are dimensioned at the top of the flanges
- Other modules are dimensioned at the top (climbing walls, caps for the
posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Place two times 2 and two times 3
3 - Place three times 1, attach them to 2 and 3
4 - Check that the equipment conforms to the dimensions shown on sheet
'dimensions'
5 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the fasteners
2 - Check the dimensions of the safety area with regard to the play equipment
1
2
3

LOGBOOK
Type indication Figura Play
Article number BBPE040.4B
Product Name Tumble bars Trio H1.45-1.20-1.00
Maximum fall height 1,5 m
Construction year 2023
Certificate 133368
Inspection body Keurmerkinstituut
Groeneweg 2e, Zoetermeer
2718AA Zoetermeer
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

© Copyright BOERplay 22-2-2022 Revision: A MOD BBP 009 x
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR

© Copyright BOERplay 22-2-2022 Revision: A MOD BBP 009 x
SME.BBP.013
x
1
BSR.002.005.050
x
6
KST.ROR.006.000
x
6
BSR.014.005.052
x
6
Metalen staanders
Pfosten aus Metall
Postes de metal
Poteaux en métal
Metal posts
NL
DE
ES
FR
Plastic or wooden posts
NL
DE
ES
FR
Kunststof of houten staanders
Pfosten aus Kunststoff oder Holz
Postes de plástico o madera
Poteaux en plastique ou en bois
Detail A (2x)
1
/1
AA
ø5mm
BSR.014.005.052
18 mm
ø3mm x 30
KST.ROR.006.000
BSR.002.005.050
50 mm
... mm
Check 'order of assembly'
controleer 'Montagevolgorde'
überprüfen Sie die ,Montagereihenfolge'
verifica el 'Orden de esemblado'
vérifiez  Ordre de montage 
NL
DE
ES
FR

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD BBP 024 B A
Aanbouwduikel 1,1 m
Boer Basic play ZO
15-7-2019
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
4, x 1 - RVS A2-70
Klinknagel bolkop
052005014BSR41
Rond 6Lamellenstop
006013LAMKST12
DuikelStaander 1,75m
905029BBPOME13
Paalkap 100x100C204100
KAP
OME
14
100 x 100
Voetplaat
C
VZP
903
VRB
OME1
5
4
2
3
5
1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD BBP 047 B
Staander 0,95m los
Boer Basics ZO
15-7-2019
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
OpmerkingBenamingRev.Bew.Volgnr.Progr.Type#Nr.
4,8 x 18 - RVS A2-70
linknagel bolkop
052005014BSR41
Rond 6Lamellenstop
006013
LAM
ST
1
2
0,95m vloerStaander 2,3m
905050
BBP
OME
1
3
AluminiumPaalkap 100x100
B204100APOME14
100 x 100VoetplaatC
VZP
903
VRB
OME
15
Grondmarkering
Ground level marker
502
4
3
2
5
1
Powered by TCPDF (www.tcpdf.org)