Bogen Nyquist NQ-S1810CT-G2 User manual

1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2020, Bogen Communications, Inc.
OF THE POSSIBILITY OF SUCH DAMAGES OR
LOSSES. Some States do not allow the exclusion or
limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply
to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from
State to State.
Products that are out of warranty will also be
repaired by Bogen Factory Service Department
-- same address as above or call 201-934-8500, at
owner’s expense. Returned products which do not
qualify for warranty service, may be repaired or re-
placed at Bogen’s option with a previously repaired
or refurbished items. The parts and labor involved
in these repairs are warranted for 90 days when
repaired by the Bogen Factory Service Department.
All parts and labor charges as well as shipping
charges will be at the owner’s expense.
All returns require a Return Authorization number.
For most efficient warranty or repair service, please
include a description of the failure.
9/2019
Publication Number 740-00123
2006
NQ-S1810CT-G2
Nyquist
Gen-2 VoIP
Ceiling Speaker
Installation
With the Nyquist Series Gen-2 VoIP Ceiling
Speaker, there is no need for external amplifiers,
traditional intercom wiring, or transformer taps
to manually set or adjust. Connect the speaker
via Cat5 to a Power-Over-Ethernet (PoE) Switch
or PoE Injector, and it is ready to use.
The speaker features an integrated 10 watt
power amplifier, a CAN Bus interface, a MEMS
digital microphone for superior talkback audio,
and a Form C SPDT type 2-amp dry contact relay
for controlling/overriding third-party devices like
AV sources.
The speaker also allows DHCP deployment
for easy installation. You can let your Nyquist
server automatically discover and configure
your speaker, or you can manually configure it
through the speaker’s web-based user interface
NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 1 of 6 - Pages(12, 1)NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 1 of 6 - Pages(12, 1) 9/10/2019 8:16:16 AM9/10/2019 8:16:16 AM

2
1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2020, Bogen Communications, Inc.
(web UI). The web UI also allows easy updating
of firmware and setting of parameters for Digital
Signal Processing (DSP). For more information
about the web UI, refer to the Nyquist Gen-2
VoIP Speakers Configuration Manual.
Speaker Layout
The layout of the speakers should be planned
before installation begins. Layout starts in one
1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2019, Bogen Communications, Inc.
11
Department: 4570 Shelby Air Drive, Suite 11, Mem-
phis, TN 38118, USA. Repaired or replacement pro-
duct(s) will be returned to you freight prepaid. This
warranty does not extend to any of our products
that have been subjected to abuse, misuse, improp-
er storage, neglect, accident, improper installation
or have been modified or repaired or altered in any
manner whatsoever, or where the serial number or
date code has been removed or defaced.
THE FOREGOING LIMITED WARRANTY IS BOGEN’S
SOLE AND EXCLUSIVE WARRANTY AND THE PUR-
CHASER’S SOLE AND EXCLUSIVE REMEDY. BOGEN
MAKES NO OTHER WARRANTIES OF ANY KIND,
EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED
WARRANTIES OF MERCHANTABILITY OR FIT-
NESS FOR A PARTICULAR PURPOSE ARE HEREBY
DISCLAIMED AND EXCLUDED TO THE MAXIMUM
EXTENT ALLOWABLE BY LAW. Bogen’s liability
arising out of the manufacture, sale or supplying of
products or their use or disposition, whether based
upon warranty, contract, tort or otherwise, shall be
limited to the price of the product. IN NO EVENT
SHALL BOGEN BE LIABLE FOR SPECIAL, INCIDEN-
TAL OR CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF
DATA OR LOSS OF USE DAMAGES) ARISING OUT
OF THE MANUFACTURE, SALE OR SUPPLYING OF
PRODUCTS, EVEN IF BOGEN HAS BEEN ADVISED
NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 2 of 6 - Pages(2, 11)NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 2 of 6 - Pages(2, 11) 9/10/2019 8:17:11 AM9/10/2019 8:17:11 AM

1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2019, Bogen Communications, Inc.
10
Compliance
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital de-
vice, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protec-
tion against harmful interference when the equip-
ment is operated in a commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instruction manual,
may cause harmful interference to radio communi-
cations. Operation of this equipment in a residen-
tial area is likely to cause harmful interference; in
which case, the user will be required to correct the
interference at his own expense.
Limited Warranty, Exlusion of Certain Damages
The NQ-S1810CT-G2 is warranted to be free from
defects in materials and workmanship for five (5)
years from the date of sale to the original purchas-
er. Any part of the product covered by this warranty
that, with normal installation and use, becomes
defective (as confirmed by Bogen upon inspection)
during the warranty period will be repaired or re-
placed by Bogen, at Bogen’s option, with new or re-
furbished product, provided the product is shipped
insured and prepaid to: Bogen Factory Service
3
1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2020, Bogen Communications, Inc.
corner of the room. The first speaker should be
positioned from each wall spaced a distance
approximately equal to the ceiling height of the
room.
The next speaker in row 1 should be spaced a
distance approximately equal to twice the height
of the ceiling. Each additional speaker in the row
should use this same spacing.
Row 2 starts at twice the ceiling height distance
from row 1 and twice the ceiling height from the
wall. The other speakers in this row are also
spaced at twice the ceiling height.
Row 3 is again spaced at twice the ceiling height
from the previous row. The first speaker start-
ing this row is positioned at one ceiling height
distance from the wall (similar to row 1).
Continue this pattern of alternating rows until
the room is covered. The spacing of the speak-
ers can be adjusted so that the speakers are
evenly spaced in a row and are aesthetically
pleasing.
NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 3 of 6 - Pages(10, 3)NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 3 of 6 - Pages(10, 3) 9/10/2019 8:17:12 AM9/10/2019 8:17:12 AM

4
1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2020, Bogen Communications, Inc.
RE84 Recessed Enclosure
The RE84 is an optional
back box for ceiling speak-
ers. UL Listed for use where
ceiling plenum is part of an
air handling system, the RE84 also includes
attachment tabs allowing the enclosure to be
supported from structures other than the actu-
al ceiling grid.
TB8 Tile Bridge
The TB8 sup-
ports the weight
of the speaker
and recessed enclosure.
This is also the item to
which the speaker mounting screws attach.
The TB8 is required for each speaker assembly
installed.
MR8 Mounting Ring
The MR8 Mounting Ring is a
cold-rolled steel unit, which will
mount any of the Bogen ceiling
grilles, for installations where
the RE84 is not used.
1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2019, Bogen Communications, Inc.
9
ministrator Manual for detailed instructions on
how to configure these speakers.
Additional Accessories
The Nyquist VoIP Ceiling Speaker can be used
with the Nyquist Digital Call Switch NQ-E7020.
Refer to the NQ-E7020 Digital Call Switch
Quick Start Guide.
Using the Reset Button
The Reset button allows you to
either reboot the VoIP speaker
or to reset the appliance’s con-
figuration settings to the fac-
tory default settings. For more
information about resetting
configuration settings, refer to
the Nyquist Gen-2 VoIP Speakers Configuration
Manual.
NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 4 of 6 - Pages(4, 9)NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 4 of 6 - Pages(4, 9) 9/10/2019 8:17:12 AM9/10/2019 8:17:12 AM

1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2019, Bogen Communications, Inc.
8
7. To connect a third-party device to the dry
contact relay output, do one of the follow-
ing:
a. If the device is looking for a Normally
Open contact, connect the device using
the NO and COM terminals.
b. If the device is looking for a Normally
Closed contact, connect the device
using the NC and COM terminals.
8. Make the electri-
cal connections
using Category 5
or higher Ethernet
cable with an RJ-45
connector.
The power is
supplied by PoE using an 802.3af compli-
ant network switch or PoE injector.
9. Place the entire assembled ceiling tile back
into the ceiling grid.
NOTE: Refer to the Nyquist Gen-2 VoIP Speak-
ers Configuration Manual or the System Ad-
Figure 4
5
1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2020, Bogen Communications, Inc.
Speaker Installation
1. Remove the tile from ceiling and center the
TB8 tile bridge on the back. Use the tile
bridge to trace out, and then cut an 8-1/2”
square hole.
NOTE: It can be more efficient to stack
multiple ceiling tiles and then cut the
speaker opening in a number of them at
one time.
Figure 1
NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 5 of 6 - Pages(8, 5)NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 5 of 6 - Pages(8, 5) 9/10/2019 8:17:13 AM9/10/2019 8:17:13 AM

6
1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2020, Bogen Communications, Inc.
2. If using the optional RE84 Recessed Enclo-
sure, bend up the 4 horseshoe tabs (Figure
1) on the TB8.
3. Position the TB8 over the hole in the tile and
push down the locator tabs (Figure 2).
Figure 2
4. Using the 4 supplied screws, attach the
speaker to the TB8 using the 4 clips in the
corners of the opening on the TB8 as nuts.
1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2019, Bogen Communications, Inc.
7
NQ-E7020 Digital
Call Switch
NOTE: Only tighten the screws until the
grille is snug against the tile. Over tight-
ening will cause the screws to dimple the
grille.
Figure 3
5. When applicable, use the pluggable CAN
bus connector to attach one or more NQ-
E7020 Digital Call Switches to the Nyquist
VoIP Form C Module 820-00071-00 as
shown in Figure 3.
6. If the CAN Bus is to be used, ensure
CAN_H and CAN_L use (Cat5 10/100)
twisted pair cable.
NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 6 of 6 - Pages(6, 7)NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 6 of 6 - Pages(6, 7) 9/10/2019 8:17:14 AM9/10/2019 8:17:14 AM

1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2019, Bogen Communications, Inc.
6
2. If using the optional RE84 Recessed Enclo-
sure, bend up the 4 horseshoe tabs (Figure
1) on the TB8.
3. Position the TB8 over the hole in the tile and
push down the locator tabs (Figure 2).
Figure 2
4. Using the 4 supplied screws, attach the
speaker to the TB8 using the 4 clips in the
corners of the opening on the TB8 as nuts.
7
1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2020, Bogen Communications, Inc.
NQ-E7020 Digital
Call Switch
NOTE: Only tighten the screws until the
grille is snug against the tile. Over tight-
ening will cause the screws to dimple the
grille.
Figure 3
5. When applicable, use the pluggable CAN
bus connector to attach one or more NQ-
E7020 Digital Call Switches to the Nyquist
VoIP Form C Module 820-00071-00 as
shown in Figure 3.
6. If the CAN Bus is to be used, ensure
CAN_H and CAN_L use (Cat5 10/100)
twisted pair cable.
NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 6 of 6 - Pages(6, 7)NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 6 of 6 - Pages(6, 7) 9/10/2019 8:17:14 AM9/10/2019 8:17:14 AM

8
1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2020, Bogen Communications, Inc.
7. To connect a third-party device to the dry
contact relay output, do one of the follow-
ing:
a. If the device is looking for a Normally
Open contact, connect the device using
the NO and COM terminals.
b. If the device is looking for a Normally
Closed contact, connect the device
using the NC and COM terminals.
8. Make the electri-
cal connections
using Category 5
or higher Ethernet
cable with an RJ-45
connector.
The power is
supplied by PoE using an 802.3af compli-
ant network switch or PoE injector.
9. Place the entire assembled ceiling tile back
into the ceiling grid.
NOTE: Refer to the Nyquist Gen-2 VoIP Speak-
ers Configuration Manual or the System Ad-
Figure 4
1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2019, Bogen Communications, Inc.
5
Speaker Installation
1. Remove the tile from ceiling and center the
TB8 tile bridge on the back. Use the tile
bridge to trace out, and then cut an 8-1/2”
square hole.
NOTE: It can be more efficient to stack
multiple ceiling tiles and then cut the
speaker opening in a number of them at
one time.
Figure 1
NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 5 of 6 - Pages(8, 5)NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 5 of 6 - Pages(8, 5) 9/10/2019 8:17:13 AM9/10/2019 8:17:13 AM

1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2019, Bogen Communications, Inc.
4
RE84 Recessed Enclosure
The RE84 is an optional
back box for ceiling speak-
ers. UL Listed for use where
ceiling plenum is part of an
air handling system, the RE84 also includes
attachment tabs allowing the enclosure to be
supported from structures other than the actu-
al ceiling grid.
TB8 Tile Bridge
The TB8 sup-
ports the weight
of the speaker
and recessed enclosure.
This is also the item to
which the speaker mounting screws attach.
The TB8 is required for each speaker assembly
installed.
MR8 Mounting Ring
The MR8 Mounting Ring is a
cold-rolled steel unit, which will
mount any of the Bogen ceiling
grilles, for installations where
the RE84 is not used.
9
1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2020, Bogen Communications, Inc.
ministrator Manual for detailed instructions on
how to configure these speakers.
Additional Accessories
The Nyquist VoIP Ceiling Speaker can be used
with the Nyquist Digital Call Switch NQ-E7020.
Refer to the NQ-E7020 Digital Call Switch
Quick Start Guide.
Using the Reset Button
The Reset button allows you to
either reboot the VoIP speaker
or to reset the appliance’s con-
figuration settings to the fac-
tory default settings. For more
information about resetting
configuration settings, refer to
the Nyquist Gen-2 VoIP Speakers Configuration
Manual.
NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 4 of 6 - Pages(4, 9)NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 4 of 6 - Pages(4, 9) 9/10/2019 8:17:12 AM9/10/2019 8:17:12 AM

10
1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2020, Bogen Communications, Inc.
Compliance
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital de-
vice, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protec-
tion against harmful interference when the equip-
ment is operated in a commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instruction manual,
may cause harmful interference to radio communi-
cations. Operation of this equipment in a residen-
tial area is likely to cause harmful interference; in
which case, the user will be required to correct the
interference at his own expense.
Limited Warranty, Exlusion of Certain Damages
The NQ-S1810CT-G2 is warranted to be free from
defects in materials and workmanship for five (5)
years from the date of sale to the original purchas-
er. Any part of the product covered by this warranty
that, with normal installation and use, becomes
defective (as confirmed by Bogen upon inspection)
during the warranty period will be repaired or re-
placed by Bogen, at Bogen’s option, with new or re-
furbished product, provided the product is shipped
insured and prepaid to: Bogen Factory Service
1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2019, Bogen Communications, Inc.
3
corner of the room. The first speaker should be
positioned from each wall spaced a distance
approximately equal to the ceiling height of the
room.
The next speaker in row 1 should be spaced a
distance approximately equal to twice the height
of the ceiling. Each additional speaker in the row
should use this same spacing.
Row 2 starts at twice the ceiling height distance
from row 1 and twice the ceiling height from the
wall. The other speakers in this row are also
spaced at twice the ceiling height.
Row 3 is again spaced at twice the ceiling height
from the previous row. The first speaker start-
ing this row is positioned at one ceiling height
distance from the wall (similar to row 1).
Continue this pattern of alternating rows until
the room is covered. The spacing of the speak-
ers can be adjusted so that the speakers are
evenly spaced in a row and are aesthetically
pleasing.
NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 3 of 6 - Pages(10, 3)NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 3 of 6 - Pages(10, 3) 9/10/2019 8:17:12 AM9/10/2019 8:17:12 AM

1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2019, Bogen Communications, Inc.
2
(web UI). The web UI also allows easy updating
of firmware and setting of parameters for Digital
Signal Processing (DSP). For more information
about the web UI, refer to the Nyquist Gen-2
VoIP Speakers Configuration Manual.
Speaker Layout
The layout of the speakers should be planned
before installation begins. Layout starts in one
11
1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2020, Bogen Communications, Inc.
Department: 4570 Shelby Air Drive, Suite 11, Mem-
phis, TN 38118, USA. Repaired or replacement pro-
duct(s) will be returned to you freight prepaid. This
warranty does not extend to any of our products
that have been subjected to abuse, misuse, improp-
er storage, neglect, accident, improper installation
or have been modified or repaired or altered in any
manner whatsoever, or where the serial number or
date code has been removed or defaced.
THE FOREGOING LIMITED WARRANTY IS BOGEN’S
SOLE AND EXCLUSIVE WARRANTY AND THE PUR-
CHASER’S SOLE AND EXCLUSIVE REMEDY. BOGEN
MAKES NO OTHER WARRANTIES OF ANY KIND,
EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED
WARRANTIES OF MERCHANTABILITY OR FIT-
NESS FOR A PARTICULAR PURPOSE ARE HEREBY
DISCLAIMED AND EXCLUDED TO THE MAXIMUM
EXTENT ALLOWABLE BY LAW. Bogen’s liability
arising out of the manufacture, sale or supplying of
products or their use or disposition, whether based
upon warranty, contract, tort or otherwise, shall be
limited to the price of the product. IN NO EVENT
SHALL BOGEN BE LIABLE FOR SPECIAL, INCIDEN-
TAL OR CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF
DATA OR LOSS OF USE DAMAGES) ARISING OUT
OF THE MANUFACTURE, SALE OR SUPPLYING OF
PRODUCTS, EVEN IF BOGEN HAS BEEN ADVISED
NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 2 of 6 - Pages(2, 11)NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 2 of 6 - Pages(2, 11) 9/10/2019 8:17:11 AM9/10/2019 8:17:11 AM

1200 MacArthur Blvd. Suite 304,
Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2020, Bogen Communications, Inc.
OF THE POSSIBILITY OF SUCH DAMAGES OR
LOSSES. Some States do not allow the exclusion or
limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply
to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from
State to State.
Products that are out of warranty will also be
repaired by Bogen Factory Service Department
-- same address as above or call 201-934-8500, at
owner’s expense. Returned products which do not
qualify for warranty service, may be repaired or re-
placed at Bogen’s option with a previously repaired
or refurbished items. The parts and labor involved
in these repairs are warranted for 90 days when
repaired by the Bogen Factory Service Department.
All parts and labor charges as well as shipping
charges will be at the owner’s expense.
All returns require a Return Authorization number.
For most efficient warranty or repair service, please
include a description of the failure.
9/2019
Publication Number 740-00123
2006
NQ-S1810CT-G2
Nyquist
Gen-2 VoIP
Ceiling Speaker
Installation
With the Nyquist Series Gen-2 VoIP Ceiling
Speaker, there is no need for external amplifiers,
traditional intercom wiring, or transformer taps
to manually set or adjust. Connect the speaker
via Cat5 to a Power-Over-Ethernet (PoE) Switch
or PoE Injector, and it is ready to use.
The speaker features an integrated 10 watt
power amplifier, a CAN Bus interface, a MEMS
digital microphone for superior talkback audio,
and a Form C SPDT type 2-amp dry contact relay
for controlling/overriding third-party devices like
AV sources.
The speaker also allows DHCP deployment
for easy installation. You can let your Nyquist
server automatically discover and configure
your speaker, or you can manually configure it
through the speaker’s web-based user interface
NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 1 of 6 - Pages(12, 1)NQ_S1810CT_G2 Ceiling Speaker Installation Manual.indd Spread 1 of 6 - Pages(12, 1) 9/10/2019 8:16:16 AM9/10/2019 8:16:16 AM
Other manuals for Nyquist NQ-S1810CT-G2
3
Table of contents
Other Bogen Speakers manuals

Bogen
Bogen CSD2X2 User manual

Bogen
Bogen CSD1X2NBVR Owner's manual

Bogen
Bogen NEAR A12 User manual

Bogen
Bogen SMTB User manual

Bogen
Bogen NEAR Orbit OCS1 User manual

Bogen
Bogen ASM1 User manual

Bogen
Bogen AMBSL1 User manual

Bogen
Bogen Bogen NEAR ORBIT OPS1 Guide

Bogen
Bogen CSD2X2 User manual

Bogen
Bogen AH15A Guide