Bogen NEAR IGS212 User manual

Specifications are subject to change without notice.
© 2017 Bogen Communications, Inc.
740-00028A
1704
LIMITED WARRANTY: Exclusion of Certain Damages
NEAR® is a division of Bogen Communications, Inc.
www.nearspeakers.com
The NEAR®IGS212 Subwoofer is warranted to be free from defects in material and workmanship for 5 (five) years from
the date of sale to the original purchaser. Any part of any NEAR product covered by this warranty that, with normal
installation and use, becomes defective (as confirmed by Bogen upon inspection) during the applicable warranty period,
will be repaired or replaced by Bogen, at Bogen’s option, provided the product is shipped insured and prepaid to: Bogen Factory
Service Department, 4570 Shelby Air Drive, Suite 11, Memphis TN 38118, USA. Repaired or replacement product will be returned
to you freight prepaid. This warranty does not extend to any of our products that have been subjected to abuse, misuse,
improper storage, neglect, accident, improper installation, or have been modified or repaired or altered in any manner whatsoever,
or where the serial number or date code has been removed or defaced.
THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER’S SOLE
AND EXCLUSIVE REMEDY FOR NEAR PRODUCTS. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER
EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen's liability
arising out of the manufacture, sale, or supplying of NEAR products or their use or disposition, whether based upon warranty,
contract, tort or otherwise, shall be limited to the price of the product. IN NO EVENT SHALL BOGEN BE LIABLE FOR SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA,
OR LOSS OF USE DAMAGES) ARISING OUT OF THE MANUFACTURE, SALE OR SUPPLYING OF NEAR PRODUCTS, EVEN
IF BOGEN HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSSES. Some States do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from State to State.
NEAR products that are out of warranty will also be repaired by the Bogen Factory Service Department -- same address as above
or call 201-934-8500. The parts and labor involved in these repairs are warranted for 90 days when repaired by the Bogen
Factory Service Department. All shipping charges in addition to parts and labor charges will be at the owner's expense. All returns
require a Return Authorization number. For most efficient warranty or repair service, please include a description of the failure.
Products manufactured and labeled by other companies may be covered by warranties offered by such companies. Please call
Bogen Customer Service or refer to product packaging for manufacturer’s warranty for non-NEAR branded products.
11/2014
YOU MUST ACCURATELY FOLLOW THE INSTRUCTIONS
FOR ALL THE PARTS INVOLVED IN THIS INSTALLATION.
FAILURE TO DO SO CAN CAUSE SERIOUS INJURY OR
DEATH TO YOURSELF OR OTHERS AND MAY EXPOSE
YOU TO POSSIBLE LEGAL ACTION
.
ALL-ENVIRONMENT IN-GROUND,
OUTDOOR SUBWOOFER
QUICK START INSTALLATION & SETUP GUIDE
Model
IGS212
IGS212
Dual 12-inch Metal Alloy Woofers
ALL-ENVIRONMENT IN-GROUND,
OUTDOOR SUBWOOFER
featuring Dual 12-inch Metal Alloy Woofers
Thank you for your purchase of the NEAR IGS212 subwoofer! This guide will assist
in the proper installation of your subwoofer. When you couple the IGS212 with the
NEAR XL-Series amplifiers, you are ensured the highest level of bass performance.
By taking a few moments to review this setup guide, you ensure that your new system
will quickly deliver audiophile-quality musical reproduction. The IGS212 is a sealed
bandpass, outdoor subwoofer that provides exceptionally high-impact natural sound
and can withstand nearly all types of environment and weather conditions. The
subwoofer combines two industry-leading technologies from NEAR: Metal Diaphragm
Technology (MDT), which ensures speaker cone stability in all-environmental conditions,
and Magnetic Liquid Suspension (MLS), a Ferrofluid seal around the magnet gap
and voice coil that provides protection from moisture and corrosion as well as
near-perfect voice coil alignment. Incidentally, the in-ground bandpass subwoofer
design was originally patented by NEAR.
Dispersion of the IGS212 is a full 360 degrees! This means that the orientation of the
subwoofer is not critical. We recommend that you install the subwoofer in-ground.
The packed earth around the enclosure suppresses enclosure resonance for improved
low-frequency definition. The IGS212’s enclosure features drainage channels to drain
water that may enter the enclosure via the bass vents.
Placement and Sound Quality
1In-ground Installation
and Connection of
IGS212 Subwoofer
Speaker cables from the amplifier to the
subwoofer may be directly buried provided
you use direct burial-rated stranded speaker
cable. We highly recommend the use of a
1” to 1-1/2” ID conduit to protect the wires
from degradation and damage due to exca-
vation or normal gardening activities. The
NEAR IGS212 subwoofer has entry and exit
wire/conduit channels on the bottom of the
enclosure. We highly recommend the use
of the NEAR IE1 junction box.
*OPTIONAL: ORDER SEPARATELY
UNDERSIDE
VIEW OF
THE IGS212
SUBWOOFER
SPEAKER
INPUT
CABLE
CONDUIT
CHANNEL
*IE-1 DIRECT BURIAL
JUNCTION BOX
*IE-1
DIRECT BURIAL
JUNCTION BOX
FEED FROM
AMPLIFIER
Remove Pre-Installed
Jumpers (2X)
Connections using the
NEAR IE1 Junction Box
DETAIL
A
SPEAKER INPUT CABLE
BLACK
(COMMON)
RED
(POSITIVE)
FROM
AMP
(
+
)
Model IGS212
Subwoofer Features
1. Two (2) 12-inch diameter Metal Alloy
Diaphragm Woofers (Internally)
2. High-Density reinforced
enclosure with UV inhibitors
3. Low turbulence output vents (3)
with protective screens
5. Input Connection Cable
4. Wiring/Conduit Channels
(underside)
2
3
1
SIDE VIEW
ABOVE
VIEW
UNDERSIDE
VIEW
4
5
FROM SPEAKER
(
+
)(
-
)
(
-
)
SPEAKER
INPUT CABLE

Specifications are subject to change without notice.
© 2017 Bogen Communications, Inc.
740-00028A
1704
LIMITED WARRANTY: Exclusion of Certain Damages
NEAR® is a division of Bogen Communications, Inc.
www.nearspeakers.com
The NEAR®IGS212 Subwoofer is warranted to be free from defects in material and workmanship for 5 (five) years from
the date of sale to the original purchaser. Any part of any NEAR product covered by this warranty that, with normal
installation and use, becomes defective (as confirmed by Bogen upon inspection) during the applicable warranty period,
will be repaired or replaced by Bogen, at Bogen’s option, provided the product is shipped insured and prepaid to: Bogen Factory
Service Department, 4570 Shelby Air Drive, Suite 11, Memphis TN 38118, USA. Repaired or replacement product will be returned
to you freight prepaid. This warranty does not extend to any of our products that have been subjected to abuse, misuse,
improper storage, neglect, accident, improper installation, or have been modified or repaired or altered in any manner whatsoever,
or where the serial number or date code has been removed or defaced.
THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER’S SOLE
AND EXCLUSIVE REMEDY FOR NEAR PRODUCTS. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER
EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen's liability
arising out of the manufacture, sale, or supplying of NEAR products or their use or disposition, whether based upon warranty,
contract, tort or otherwise, shall be limited to the price of the product. IN NO EVENT SHALL BOGEN BE LIABLE FOR SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA,
OR LOSS OF USE DAMAGES) ARISING OUT OF THE MANUFACTURE, SALE OR SUPPLYING OF NEAR PRODUCTS, EVEN
IF BOGEN HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSSES. Some States do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from State to State.
NEAR products that are out of warranty will also be repaired by the Bogen Factory Service Department -- same address as above
or call 201-934-8500. The parts and labor involved in these repairs are warranted for 90 days when repaired by the Bogen
Factory Service Department. All shipping charges in addition to parts and labor charges will be at the owner's expense. All returns
require a Return Authorization number. For most efficient warranty or repair service, please include a description of the failure.
Products manufactured and labeled by other companies may be covered by warranties offered by such companies. Please call
Bogen Customer Service or refer to product packaging for manufacturer’s warranty for non-NEAR branded products.
11/2014
YOU MUST ACCURATELY FOLLOW THE INSTRUCTIONS
FOR ALL THE PARTS INVOLVED IN THIS INSTALLATION.
FAILURE TO DO SO CAN CAUSE SERIOUS INJURY OR
DEATH TO YOURSELF OR OTHERS AND MAY EXPOSE
YOU TO POSSIBLE LEGAL ACTION
.
ALL-ENVIRONMENT IN-GROUND,
OUTDOOR SUBWOOFER
QUICK START INSTALLATION & SETUP GUIDE
Model
IGS212
IGS212
Dual 12-inch Metal Alloy Woofers
ALL-ENVIRONMENT IN-GROUND,
OUTDOOR SUBWOOFER
featuring Dual 12-inch Metal Alloy Woofers
Thank you for your purchase of the NEAR IGS212 subwoofer! This guide will assist
in the proper installation of your subwoofer. When you couple the IGS212 with the
NEAR XL-Series amplifiers, you are ensured the highest level of bass performance.
By taking a few moments to review this setup guide, you ensure that your new system
will quickly deliver audiophile-quality musical reproduction. The IGS212 is a sealed
bandpass, outdoor subwoofer that provides exceptionally high-impact natural sound
and can withstand nearly all types of environment and weather conditions. The
subwoofer combines two industry-leading technologies from NEAR: Metal Diaphragm
Technology (MDT), which ensures speaker cone stability in all-environmental conditions,
and Magnetic Liquid Suspension (MLS), a Ferrofluid seal around the magnet gap
and voice coil that provides protection from moisture and corrosion as well as
near-perfect voice coil alignment. Incidentally, the in-ground bandpass subwoofer
design was originally patented by NEAR.
Dispersion of the IGS212 is a full 360 degrees! This means that the orientation of the
subwoofer is not critical. We recommend that you install the subwoofer in-ground.
The packed earth around the enclosure suppresses enclosure resonance for improved
low-frequency definition. The IGS212’s enclosure features drainage channels to drain
water that may enter the enclosure via the bass vents.
Placement and Sound Quality
1In-ground Installation
and Connection of
IGS212 Subwoofer
Speaker cables from the amplifier to the
subwoofer may be directly buried provided
you use direct burial-rated stranded speaker
cable. We highly recommend the use of a
1” to 1-1/2” ID conduit to protect the wires
from degradation and damage due to exca-
vation or normal gardening activities. The
NEAR IGS212 subwoofer has entry and exit
wire/conduit channels on the bottom of the
enclosure. We highly recommend the use
of the NEAR IE1 junction box.
*OPTIONAL: ORDER SEPARATELY
UNDERSIDE
VIEW OF
THE IGS212
SUBWOOFER
SPEAKER
INPUT
CABLE
CONDUIT
CHANNEL
*IE-1 DIRECT BURIAL
JUNCTION BOX
*IE-1
DIRECT BURIAL
JUNCTION BOX
FEED FROM
AMPLIFIER
Remove Pre-Installed
Jumpers (2X)
Connections using the
NEAR IE1 Junction Box
DETAIL
A
SPEAKER INPUT CABLE
BLACK
(COMMON)
RED
(POSITIVE)
FROM
AMP
(
+
)
Model IGS212
Subwoofer Features
1. Two (2) 12-inch diameter Metal Alloy
Diaphragm Woofers (Internally)
2. High-Density reinforced
enclosure with UV inhibitors
3. Low turbulence output vents (3)
with protective screens
5. Input Connection Cable
4. Wiring/Conduit Channels
(underside)
2
3
1
SIDE VIEW
ABOVE
VIEW
UNDERSIDE
VIEW
4
5
FROM SPEAKER
(
+
)(
-
)
(
-
)
SPEAKER
INPUT CABLE

Specifications are subject to change without notice.
© 2017 Bogen Communications, Inc.
740-00028A
1704
LIMITED WARRANTY: Exclusion of Certain Damages
NEAR® is a division of Bogen Communications, Inc.
www.nearspeakers.com
The NEAR®IGS212 Subwoofer is warranted to be free from defects in material and workmanship for 5 (five) years from
the date of sale to the original purchaser. Any part of any NEAR product covered by this warranty that, with normal
installation and use, becomes defective (as confirmed by Bogen upon inspection) during the applicable warranty period,
will be repaired or replaced by Bogen, at Bogen’s option, provided the product is shipped insured and prepaid to: Bogen Factory
Service Department, 4570 Shelby Air Drive, Suite 11, Memphis TN 38118, USA. Repaired or replacement product will be returned
to you freight prepaid. This warranty does not extend to any of our products that have been subjected to abuse, misuse,
improper storage, neglect, accident, improper installation, or have been modified or repaired or altered in any manner whatsoever,
or where the serial number or date code has been removed or defaced.
THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER’S SOLE
AND EXCLUSIVE REMEDY FOR NEAR PRODUCTS. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER
EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen's liability
arising out of the manufacture, sale, or supplying of NEAR products or their use or disposition, whether based upon warranty,
contract, tort or otherwise, shall be limited to the price of the product. IN NO EVENT SHALL BOGEN BE LIABLE FOR SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA,
OR LOSS OF USE DAMAGES) ARISING OUT OF THE MANUFACTURE, SALE OR SUPPLYING OF NEAR PRODUCTS, EVEN
IF BOGEN HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSSES. Some States do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from State to State.
NEAR products that are out of warranty will also be repaired by the Bogen Factory Service Department -- same address as above
or call 201-934-8500. The parts and labor involved in these repairs are warranted for 90 days when repaired by the Bogen
Factory Service Department. All shipping charges in addition to parts and labor charges will be at the owner's expense. All returns
require a Return Authorization number. For most efficient warranty or repair service, please include a description of the failure.
Products manufactured and labeled by other companies may be covered by warranties offered by such companies. Please call
Bogen Customer Service or refer to product packaging for manufacturer’s warranty for non-NEAR branded products.
11/2014
YOU MUST ACCURATELY FOLLOW THE INSTRUCTIONS
FOR ALL THE PARTS INVOLVED IN THIS INSTALLATION.
FAILURE TO DO SO CAN CAUSE SERIOUS INJURY OR
DEATH TO YOURSELF OR OTHERS AND MAY EXPOSE
YOU TO POSSIBLE LEGAL ACTION
.
ALL-ENVIRONMENT IN-GROUND,
OUTDOOR SUBWOOFER
QUICK START INSTALLATION & SETUP GUIDE
Model
IGS212
IGS212
Dual 12-inch Metal Alloy Woofers
ALL-ENVIRONMENT IN-GROUND,
OUTDOOR SUBWOOFER
featuring Dual 12-inch Metal Alloy Woofers
Thank you for your purchase of the NEAR IGS212 subwoofer! This guide will assist
in the proper installation of your subwoofer. When you couple the IGS212 with the
NEAR XL-Series amplifiers, you are ensured the highest level of bass performance.
By taking a few moments to review this setup guide, you ensure that your new system
will quickly deliver audiophile-quality musical reproduction. The IGS212 is a sealed
bandpass, outdoor subwoofer that provides exceptionally high-impact natural sound
and can withstand nearly all types of environment and weather conditions. The
subwoofer combines two industry-leading technologies from NEAR: Metal Diaphragm
Technology (MDT), which ensures speaker cone stability in all-environmental conditions,
and Magnetic Liquid Suspension (MLS), a Ferrofluid seal around the magnet gap
and voice coil that provides protection from moisture and corrosion as well as
near-perfect voice coil alignment. Incidentally, the in-ground bandpass subwoofer
design was originally patented by NEAR.
Dispersion of the IGS212 is a full 360 degrees! This means that the orientation of the
subwoofer is not critical. We recommend that you install the subwoofer in-ground.
The packed earth around the enclosure suppresses enclosure resonance for improved
low-frequency definition. The IGS212’s enclosure features drainage channels to drain
water that may enter the enclosure via the bass vents.
Placement and Sound Quality
1In-ground Installation
and Connection of
IGS212 Subwoofer
Speaker cables from the amplifier to the
subwoofer may be directly buried provided
you use direct burial-rated stranded speaker
cable. We highly recommend the use of a
1” to 1-1/2” ID conduit to protect the wires
from degradation and damage due to exca-
vation or normal gardening activities. The
NEAR IGS212 subwoofer has entry and exit
wire/conduit channels on the bottom of the
enclosure. We highly recommend the use
of the NEAR IE1 junction box.
*OPTIONAL: ORDER SEPARATELY
UNDERSIDE
VIEW OF
THE IGS212
SUBWOOFER
SPEAKER
INPUT
CABLE
CONDUIT
CHANNEL
*IE-1 DIRECT BURIAL
JUNCTION BOX
*IE-1
DIRECT BURIAL
JUNCTION BOX
FEED FROM
AMPLIFIER
Remove Pre-Installed
Jumpers (2X)
Connections using the
NEAR IE1 Junction Box
DETAIL
A
SPEAKER INPUT CABLE
BLACK
(COMMON)
RED
(POSITIVE)
FROM
AMP
(
+
)
Model IGS212
Subwoofer Features
1. Two (2) 12-inch diameter Metal Alloy
Diaphragm Woofers (Internally)
2. High-Density reinforced
enclosure with UV inhibitors
3. Low turbulence output vents (3)
with protective screens
5. Input Connection Cable
4. Wiring/Conduit Channels
(underside)
2
3
1
SIDE VIEW
ABOVE
VIEW
UNDERSIDE
VIEW
4
5
FROM SPEAKER
(
+
)(
-
)
(
-
)
SPEAKER
INPUT CABLE

WARNING: Customer is responsible for the wiring materials to/from amplifier and
to/from other speakers/subwoofers as well as the selection of the installation area.
It is recommended that a professional be consulted when connecting speakers if
the installer does not have sufficient knowledge in working with electrical components.
2In-ground Mounting/Burial
of IGS212 Subwoofer
When preparing an IGS212 subwoofer for burial, select an area that allows the depth
needed for the enclosure plus 6-inches to allow for a layer of crushed stone or gravel.
In most cases, the hole should be dug to a level of 18-24 inches. The lower edge of the
3 Output Vents (A) should be 2-3 inches (50-70mm) above ground level as illustrated
above. A layer of mulch or loose stone may be added up to the lower edge of the vents
as long as it allows water to flow through. Although the enclosure has channels for
draining water that may enter the enclosure through the vents, it is best to prevent
water from entering the enclosure in the first place. If the subwoofer is in a location
where water may flow around it during heavy rains, raise the subwoofer another
2-3 inches (50-75mm) above ground level. Place a layer of permeable landscape
fabric between the crushed drainage stone and the subwoofer.
LEVEL: INSTALL 1 SLOPE: INSTALL 2 SLOPE: INSTALL 3
3In-ground Install Angles
of an IGS212 Subwoofer
The IGS212 subwoofer is designed with a slightly angled driver so that when the
enclosure is on a level plane (see Install 1 & 2), any moisture will be channeled away
from the woofer. DO NOT install the subwoofer at an angle as pictured in Install 3.
4Wiring Connection Setup Example
EXAMPLE OF A HYBRID SYSTEM:
IGS212 AT 4-OHMS/SATS ON 70V
NEAR 7XL/3XL DSP POWER AMPLIFIER
When preparing an IGS212 subwoofer for burial, select an area that allows the depth
needed for the enclosure plus 6-inches to allow for a layer of crushed stone or gravel
.
In most cases, the hole should be dug to a level of 18-24 inches. The lower edge of the
IGS212
TO
AMP
EXISTING SOIL
CRUSHED
STONE
IE-1
JUNCTION BOX
MULCH, STONE,
OR GROUND COVER
(3) DRAIN
CHANNELS
A
A
A
LANDSCAPE
FABRIC
B
(3) OUTPUT VENTS
Leave approximately 2” (50mm)
clearance from the bottom of
three Output Vents to solid
ground. Mulch or loose stone
may be installed up to the bottom
of the vents.
2”
IGS212 Subwoofer combined with any NEAR
Model IG-Series speakers as “Satellites” (Sats)
0
IOFF
For different or customized systems, download from the NEAR website the NEAR
XL GUI File software (www.nearspeakers.com/xl-files.html) to your computer.
This will allow complete customization of Output, EQ, Compressor, Limiter,
Cross-Over Points and Slopes, and additional control parameters.
Channel B
Satellites
(-)
Use power taps as required on
each speaker; i.e.,... 128W, 64W, etc.
Do not exceed the wattage
total of the amplifier channel.
( + )
(-)
(
+ )
IG SERIES
LOUDSPEAKER
IG SERIES
LOUDSPEAKER
(
-
)
(
+ )
(-)
( + )
(-)
( + )
DSP PRESET:
B - IGS212 IG70V (BALANCED)
OR
U - IGS212 IG70V (UNBALANCED)
(-)
(
+ )
NEAR IGS212
SUBWOOFER
NOTE: BALANCED Inputs use the XLR connectors on the back of the amplifier.
UNBALANCED inputs use the RCA connectors on the back of the amplifier (see below).
Channel A
IGS212
NEAR 7XL/3XL Amplifier Back Panel
Use the Preset: (Bal. or Unbal.)“IGS212 IG70V”.
Channel A is IGS212;
Channel B is IG Satellites.
Balanced
Inputs (XLR)
Unbalanced
Inputs (RCA)
5Wiring Connection Setup Example
EXAMPLE OF A DUAL SUBWOOFER SYSTEM:
IGS212 AT 4-OHMS ON EACH CHANNEL
NEAR 7XL/3XL DSP POWER AMPLIFIER
Dual IGS212 Subwoofer System with
NEAR 7XL or 3XL DSP Power Amplifier
Channel B
IGS212
(-)
(
+ )
(
-
)
(
+ )
(-)
( + )
(-)
( + )
LOAD DSP PRESET FILE:
(-)
(
+ )
IGS212 SUBWOOFER
Go to www.nearspeakers.com/xl-files.html and download the appropriate
preset file for the model amplifier and input type:
• Dual IGS212 – Balanced Inputs for 7XL • Dual IGS212 – Unbalanced Inputs for 7XL
• Dual IGS212 – Balanced Inputs for 3XL • Dual IGS212 – Unbalanced Inputs for 3XL
Channel A
IGS212
IGS212 SUBWOOFER
NOTE: BALANCED Inputs use the XLR
connectors on the back of the amplifier.
UNBALANCED inputs use the RCA con-
nectors located on the back of amplifier.
(see below).
www.nearspeakers.com
CH.B (+)
CH.B (-)
CH.A (+)
CH.A (-)
0
IOFF
NEAR 7XL/3XL Amplifier Back Panel
Balanced
Inputs (XLR)
Unbalanced
Inputs (RCA)
CH.B (+)
CH.B (-)
CH.A (+)
CH.A (-)
®
For different or customized systems, download from the NEAR website the NEAR
XL GUI File software (www.nearspeakers.com/xl-files.html) to your computer.
This will allow complete customization of Output, EQ, Compressor, Limiter,
Cross-Over Points and Slopes, and additional control parameters.
LOAD
Use the LOAD function of the amplifier’s GUI
to load the preset file into the amplifier’s DSP.
Consult the 7XL/3XL amplifier manual for
more specific instructions on loading and
executing preset files.

WARNING: Customer is responsible for the wiring materials to/from amplifier and
to/from other speakers/subwoofers as well as the selection of the installation area.
It is recommended that a professional be consulted when connecting speakers if
the installer does not have sufficient knowledge in working with electrical components.
2In-ground Mounting/Burial
of IGS212 Subwoofer
When preparing an IGS212 subwoofer for burial, select an area that allows the depth
needed for the enclosure plus 6-inches to allow for a layer of crushed stone or gravel.
In most cases, the hole should be dug to a level of 18-24 inches. The lower edge of the
3 Output Vents (A) should be 2-3 inches (50-70mm) above ground level as illustrated
above. A layer of mulch or loose stone may be added up to the lower edge of the vents
as long as it allows water to flow through. Although the enclosure has channels for
draining water that may enter the enclosure through the vents, it is best to prevent
water from entering the enclosure in the first place. If the subwoofer is in a location
where water may flow around it during heavy rains, raise the subwoofer another
2-3 inches (50-75mm) above ground level. Place a layer of permeable landscape
fabric between the crushed drainage stone and the subwoofer.
LEVEL: INSTALL 1 SLOPE: INSTALL 2 SLOPE: INSTALL 3
3In-ground Install Angles
of an IGS212 Subwoofer
The IGS212 subwoofer is designed with a slightly angled driver so that when the
enclosure is on a level plane (see Install 1 & 2), any moisture will be channeled away
from the woofer. DO NOT install the subwoofer at an angle as pictured in Install 3.
4Wiring Connection Setup Example
EXAMPLE OF A HYBRID SYSTEM:
IGS212 AT 4-OHMS/SATS ON 70V
NEAR 7XL/3XL DSP POWER AMPLIFIER
IGS212
TO
AMP
EXISTING SOIL
CRUSHED
STONE
IE-1
JUNCTION BOX
MULCH, STONE,
OR GROUND COVER
(3) DRAIN
CHANNELS
A
A
A
LANDSCAPE
FABRIC
B
(3) OUTPUT VENTS
Leave approximately 2” (50mm)
clearance from the bottom of
three Output Vents to solid
ground. Mulch or loose stone
may be installed up to the bottom
of the vents.
2”
IGS212 Subwoofer combined with any NEAR
Model IG-Series speakers as “Satellites” (Sats)
0
IOFF
For different or customized systems, download from the NEAR website the NEAR
XL GUI File software (www.nearspeakers.com/xl-files.html) to your computer.
This will allow complete customization of Output, EQ, Compressor, Limiter,
Cross-Over Points and Slopes, and additional control parameters.
Channel B
Satellites
(-)
Use power taps as required on
each speaker; i.e.,... 128W, 64W, etc.
Do not exceed the wattage
total of the amplifier channel.
( + )
(-)
(
+ )
IG SERIES
LOUDSPEAKER
IG SERIES
LOUDSPEAKER
(
-
)
(
+ )
(-)
( + )
(-)
( + )
DSP PRESET:
B - IGS212 IG70V (BALANCED)
OR
U - IGS212 IG70V (UNBALANCED)
(-)
(
+ )
NEAR IGS212
SUBWOOFER
NOTE: BALANCED Inputs use the XLR connectors on the back of the amplifier.
UNBALANCED inputs use the RCA connectors on the back of the amplifier (see below).
Channel A
IGS212
NEAR 7XL/3XL Amplifier Back Panel
Use the Preset: (Bal. or Unbal.)“IGS212 IG70V”.
Channel A is IGS212;
Channel B is IG Satellites.
Balanced
Inputs (XLR)
Unbalanced
Inputs (RCA)
5Wiring Connection Setup Example
EXAMPLE OF A DUAL SUBWOOFER SYSTEM:
IGS212 AT 4-OHMS ON EACH CHANNEL
NEAR 7XL/3XL DSP POWER AMPLIFIER
Dual IGS212 Subwoofer System with
NEAR 7XL or 3XL DSP Power Amplifier
Channel B
IGS212
(-)
(
+ )
(
-
)
(
+ )
(-)
( + )
(-)
( + )
LOAD DSP PRESET FILE:
(-)
(
+ )
IGS212 SUBWOOFER
Go to www.nearspeakers.com/xl-files.html and download the appropriate
preset file for the model amplifier and input type:
• Dual IGS212 – Balanced Inputs for 7XL • Dual IGS212 – Unbalanced Inputs for 7XL
• Dual IGS212 – Balanced Inputs for 3XL • Dual IGS212 – Unbalanced Inputs for 3XL
Channel A
IGS212
IGS212 SUBWOOFER
NOTE: BALANCED Inputs use the XLR
connectors on the back of the amplifier.
UNBALANCED inputs use the RCA con-
nectors located on the back of amplifier.
(see below).
www.nearspeakers.com
CH.B (+)
CH.B (-)
CH.A (+)
CH.A (-)
0
IOFF
NEAR 7XL/3XL Amplifier Back Panel
Balanced
Inputs (XLR)
Unbalanced
Inputs (RCA)
CH.B (+)
CH.B (-)
CH.A (+)
CH.A (-)
®
For different or customized systems, download from the NEAR website the NEAR
XL GUI File software (www.nearspeakers.com/xl-files.html) to your computer.
This will allow complete customization of Output, EQ, Compressor, Limiter,
Cross-Over Points and Slopes, and additional control parameters.
LOAD
Use the LOAD function of the amplifier’s GUI
to load the preset file into the amplifier’s DSP.
Consult the 7XL/3XL amplifier manual for
more specific instructions on loading and
executing preset files.

WARNING: Customer is responsible for the wiring materials to/from amplifier and
to/from other speakers/subwoofers as well as the selection of the installation area.
It is recommended that a professional be consulted when connecting speakers if
the installer does not have sufficient knowledge in working with electrical components.
2In-ground Mounting/Burial
of IGS212 Subwoofer
When preparing an IGS212 subwoofer for burial, select an area that allows the depth
needed for the enclosure plus 6-inches to allow for a layer of crushed stone or gravel.
In most cases, the hole should be dug to a level of 18-24 inches. The lower edge of the
3 Output Vents (A) should be 2-3 inches (50-70mm) above ground level as illustrated
above. A layer of mulch or loose stone may be added up to the lower edge of the vents
as long as it allows water to flow through. Although the enclosure has channels for
draining water that may enter the enclosure through the vents, it is best to prevent
water from entering the enclosure in the first place. If the subwoofer is in a location
where water may flow around it during heavy rains, raise the subwoofer another
2-3 inches (50-75mm) above ground level. Place a layer of permeable landscape
fabric between the crushed drainage stone and the subwoofer.
LEVEL: INSTALL 1 SLOPE: INSTALL 2 SLOPE: INSTALL 3
3In-ground Install Angles
of an IGS212 Subwoofer
The IGS212 subwoofer is designed with a slightly angled driver so that when the
enclosure is on a level plane (see Install 1 & 2), any moisture will be channeled away
from the woofer. DO NOT install the subwoofer at an angle as pictured in Install 3.
4Wiring Connection Setup Example
EXAMPLE OF A HYBRID SYSTEM:
IGS212 AT 4-OHMS/SATS ON 70V
NEAR 7XL/3XL DSP POWER AMPLIFIER
IGS212
TO
AMP
EXISTING SOIL
CRUSHED
STONE
IE-1
JUNCTION BOX
MULCH, STONE,
OR GROUND COVER
(3) DRAIN
CHANNELS
A
A
A
LANDSCAPE
FABRIC
B
(3) OUTPUT VENTS
Leave approximately 2” (50mm)
clearance from the bottom of
three Output Vents to solid
ground. Mulch or loose stone
may be installed up to the bottom
of the vents.
2”
IGS212 Subwoofer combined with any NEAR
Model IG-Series speakers as “Satellites” (Sats)
0
IOFF
For different or customized systems, download from the NEAR website the NEAR
XL GUI File software (www.nearspeakers.com/xl-files.html) to your computer.
This will allow complete customization of Output, EQ, Compressor, Limiter,
Cross-Over Points and Slopes, and additional control parameters.
Channel B
Satellites
(-)
Use power taps as required on
each speaker; i.e.,... 128W, 64W, etc.
Do not exceed the wattage
total of the amplifier channel.
( + )
(-)
(
+ )
IG SERIES
LOUDSPEAKER
IG SERIES
LOUDSPEAKER
(
-
)
(
+ )
(-)
( + )
(-)
( + )
DSP PRESET:
B - IGS212 IG70V (BALANCED)
OR
U - IGS212 IG70V (UNBALANCED)
(-)
(
+ )
NEAR IGS212
SUBWOOFER
NOTE: BALANCED Inputs use the XLR connectors on the back of the amplifier.
UNBALANCED inputs use the RCA connectors on the back of the amplifier (see below).
Channel A
IGS212
NEAR 7XL/3XL Amplifier Back Panel
Use the Preset: (Bal. or Unbal.)“IGS212 IG70V”.
Channel A is IGS212;
Channel B is IG Satellites.
Balanced
Inputs (XLR)
Unbalanced
Inputs (RCA)
5Wiring Connection Setup Example
EXAMPLE OF A DUAL SUBWOOFER SYSTEM:
IGS212 AT 4-OHMS ON EACH CHANNEL
NEAR 7XL/3XL DSP POWER AMPLIFIER
Dual IGS212 Subwoofer System with
NEAR 7XL or 3XL DSP Power Amplifier
Channel B
IGS212
(-)
(
+ )
(
-
)
(
+ )
(-)
( + )
(-)
( + )
LOAD DSP PRESET FILE:
(-)
(
+ )
IGS212 SUBWOOFER
Go to www.nearspeakers.com/xl-files.html and download the appropriate
preset file for the model amplifier and input type:
• Dual IGS212 – Balanced Inputs for 7XL • Dual IGS212 – Unbalanced Inputs for 7XL
• Dual IGS212 – Balanced Inputs for 3XL • Dual IGS212 – Unbalanced Inputs for 3XL
Channel A
IGS212
IGS212 SUBWOOFER
NOTE: BALANCED Inputs use the XLR
connectors on the back of the amplifier.
UNBALANCED inputs use the RCA con-
nectors located on the back of amplifier.
(see below).
www.nearspeakers.com
CH.B (+)
CH.B (-)
CH.A (+)
CH.A (-)
0
IOFF
NEAR 7XL/3XL Amplifier Back Panel
Balanced
Inputs (XLR)
Unbalanced
Inputs (RCA)
CH.B (+)
CH.B (-)
CH.A (+)
CH.A (-)
®
For different or customized systems, download from the NEAR website the NEAR
XL GUI File software (www.nearspeakers.com/xl-files.html) to your computer.
This will allow complete customization of Output, EQ, Compressor, Limiter,
Cross-Over Points and Slopes, and additional control parameters.
LOAD
Use the LOAD function of the amplifier’s GUI
to load the preset file into the amplifier’s DSP.
Consult the 7XL/3XL amplifier manual for
more specific instructions on loading and
executing preset files.

WARNING: Customer is responsible for the wiring materials to/from amplifier and
to/from other speakers/subwoofers as well as the selection of the installation area.
It is recommended that a professional be consulted when connecting speakers if
the installer does not have sufficient knowledge in working with electrical components.
2In-ground Mounting/Burial
of IGS212 Subwoofer
When preparing an IGS212 subwoofer for burial, select an area that allows the depth
needed for the enclosure plus 6-inches to allow for a layer of crushed stone or gravel.
In most cases, the hole should be dug to a level of 18-24 inches. The lower edge of the
3 Output Vents (A) should be 2-3 inches (50-70mm) above ground level as illustrated
above. A layer of mulch or loose stone may be added up to the lower edge of the vents
as long as it allows water to flow through. Although the enclosure has channels for
draining water that may enter the enclosure through the vents, it is best to prevent
water from entering the enclosure in the first place. If the subwoofer is in a location
where water may flow around it during heavy rains, raise the subwoofer another
2-3 inches (50-75mm) above ground level. Place a layer of permeable landscape
fabric between the crushed drainage stone and the subwoofer.
LEVEL: INSTALL 1 SLOPE: INSTALL 2 SLOPE: INSTALL 3
3In-ground Install Angles
of an IGS212 Subwoofer
The IGS212 subwoofer is designed with a slightly angled driver so that when the
enclosure is on a level plane (see Install 1 & 2), any moisture will be channeled away
from the woofer. DO NOT install the subwoofer at an angle as pictured in Install 3.
4Wiring Connection Setup Example
EXAMPLE OF A HYBRID SYSTEM:
IGS212 AT 4-OHMS/SATS ON 70V
NEAR 7XL/3XL DSP POWER AMPLIFIER
IGS212
TO
AMP
EXISTING SOIL
CRUSHED
STONE
IE-1
JUNCTION BOX
MULCH, STONE,
OR GROUND COVER
(3) DRAIN
CHANNELS
A
A
A
LANDSCAPE
FABRIC
B
(3) OUTPUT VENTS
Leave approximately 2” (50mm)
clearance from the bottom of
three Output Vents to solid
ground. Mulch or loose stone
may be installed up to the bottom
of the vents.
2”
IGS212 Subwoofer combined with any NEAR
Model IG-Series speakers as “Satellites” (Sats)
0
IOFF
For different or customized systems, download from the NEAR website the NEAR
XL GUI File software (www.nearspeakers.com/xl-files.html) to your computer.
This will allow complete customization of Output, EQ, Compressor, Limiter,
Cross-Over Points and Slopes, and additional control parameters.
Channel B
Satellites
(-)
Use power taps as required on
each speaker; i.e.,... 128W, 64W, etc.
Do not exceed the wattage
total of the amplifier channel.
( + )
(-)
(
+ )
IG SERIES
LOUDSPEAKER
IG SERIES
LOUDSPEAKER
(
-
)
(
+ )
(-)
( + )
(-)
( + )
DSP PRESET:
B - IGS212 IG70V (BALANCED)
OR
U - IGS212 IG70V (UNBALANCED)
(-)
(
+ )
NEAR IGS212
SUBWOOFER
NOTE: BALANCED Inputs use the XLR connectors on the back of the amplifier.
UNBALANCED inputs use the RCA connectors on the back of the amplifier (see below).
Channel A
IGS212
NEAR 7XL/3XL Amplifier Back Panel
Use the Preset: (Bal. or Unbal.)“IGS212 IG70V”.
Channel A is IGS212;
Channel B is IG Satellites.
Balanced
Inputs (XLR)
Unbalanced
Inputs (RCA)
5
Wiring Connection Setup Example
EXAMPLE OF A DUAL SUBWOOFER SYSTEM:
IGS212 AT 4-OHMS ON EACH CHANNEL
NEAR 7XL/3XL DSP POWER AMPLIFIER
Dual IGS212 Subwoofer System with
NEAR 7XL or 3XL DSP Power Amplifier
Channel B
IGS212
(-)
(
+ )
(
-
)
(
+ )
(-)
( + )
(-)
( + )
LOAD DSP PRESET FILE:
(-)
(
+ )
IGS212 SUBWOOFER
Go to www.nearspeakers.com/xl-files.html and download the appropriate
preset file for the model amplifier and input type:
• Dual IGS212 – Balanced Inputs for 7XL • Dual IGS212 – Unbalanced Inputs for 7XL
• Dual IGS212 – Balanced Inputs for 3XL • Dual IGS212 – Unbalanced Inputs for 3XL
Channel A
IGS212
IGS212 SUBWOOFER
NOTE: BALANCED Inputs use the XLR
connectors on the back of the amplifier.
UNBALANCED inputs use the RCA con-
nectors located on the back of amplifier.
(see below).
www.nearspeakers.com
CH.B (+)
CH.B (-)
CH.A (+)
CH.A (-)
0
IOFF
NEAR 7XL/3XL Amplifier Back Panel
Balanced
Inputs (XLR)
Unbalanced
Inputs (RCA)
CH.B (+)
CH.B (-)
CH.A (+)
CH.A (-)
®
For different or customized systems, download from the NEAR website the NEAR
XL GUI File software (www.nearspeakers.com/xl-files.html) to your computer.
This will allow complete customization of Output, EQ, Compressor, Limiter,
Cross-Over Points and Slopes, and additional control parameters.
LOAD
Use the LOAD function of the amplifier’s GUI
to load the preset file into the amplifier’s DSP.
Consult the 7XL/3XL amplifier manual for
more specific instructions on loading and
executing preset files.

Specifications are subject to change without notice.
© 2017 Bogen Communications, Inc.
740-00028A
1704
LIMITED WARRANTY: Exclusion of Certain Damages
www.bogen.com
NEAR is a division of Bogen Communications, Inc.
The NEAR®IGS212 Subwoofer is warranted to be free from defects in material and workmanship for 5 (five) years from
the date of sale to the original purchaser. Any part of any NEAR product covered by this warranty that, with normal
installation and use, becomes defective (as confirmed by Bogen upon inspection) during the applicable warranty period,
will be repaired or replaced by Bogen, at Bogen’s option, provided the product is shipped insured and prepaid to: Bogen Factory
Service Department, 4570 Shelby Air Drive, Suite 11, Memphis TN 38118, USA. Repaired or replacement product will be returned
to you freight prepaid. This warranty does not extend to any of our products that have been subjected to abuse, misuse,
improper storage, neglect, accident, improper installation, or have been modified or repaired or altered in any manner whatsoever,
or where the serial number or date code has been removed or defaced.
THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER’S SOLE
AND EXCLUSIVE REMEDY FOR NEAR PRODUCTS. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER
EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen's liability
arising out of the manufacture, sale, or supplying of NEAR products or their use or disposition, whether based upon warranty,
contract, tort or otherwise, shall be limited to the price of the product. IN NO EVENT SHALL BOGEN BE LIABLE FOR SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA,
OR LOSS OF USE DAMAGES) ARISING OUT OF THE MANUFACTURE, SALE OR SUPPLYING OF NEAR PRODUCTS, EVEN
IF BOGEN HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSSES. Some States do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from State to State.
NEAR products that are out of warranty will also be repaired by the Bogen Factory Service Department -- same address as above
or call 201-934-8500. The parts and labor involved in these repairs are warranted for 90 days when repaired by the Bogen
Factory Service Department. All shipping charges in addition to parts and labor charges will be at the owner's expense. All returns
require a Return Authorization number. For most efficient warranty or repair service, please include a description of the failure.
Products manufactured and labeled by other companies may be covered by warranties offered by such companies. Please call
Bogen Customer Service or refer to product packaging for manufacturer’s warranty for non-NEAR branded products.
11/2014
YOU MUST ACCURATELY FOLLOW THE INSTRUCTIONS
FOR ALL THE PARTS INVOLVED IN THIS INSTALLATION.
FAILURE TO DO SO CAN CAUSE SERIOUS INJURY OR
DEATH TO YOURSELF OR OTHERS AND MAY EXPOSE
YOU TO POSSIBLE LEGAL ACTION
.
ALL-ENVIRONMENT IN-GROUND,
OUTDOOR SUBWOOFER
QUICK START INSTALLATION & SETUP GUIDE
Model
IGS212
IGS212
Dual 12-inch Metal Alloy Woofers
ALL-ENVIRONMENT IN-GROUND,
OUTDOOR SUBWOOFER
featuring Dual 12-inch Metal Alloy Woofers
Thank you for your purchase of the NEAR IGS212 subwoofer! This guide will assist
in the proper installation of your subwoofer. When you couple the IGS212 with the
NEAR XL-Series amplifiers, you are ensured the highest level of bass performance.
By taking a few moments to review this setup guide, you ensure that your new system
will quickly deliver audiophile-quality musical reproduction. The IGS212 is a sealed
bandpass, outdoor subwoofer that provides exceptionally high-impact natural sound
and can withstand nearly all types of environment and weather conditions. The
subwoofer combines two industry-leading technologies from NEAR: Metal Diaphragm
Technology (MDT), which ensures speaker cone stability in all-environmental conditions,
and Magnetic Liquid Suspension (MLS), a Ferrofluid seal around the magnet gap
and voice coil that provides protection from moisture and corrosion as well as
near-perfect voice coil alignment. Incidentally, the in-ground bandpass subwoofer
design was originally patented by NEAR.
Dispersion of the IGS212 is a full 360 degrees! This means that the orientation of the
subwoofer is not critical. We recommend that you install the subwoofer in-ground.
The packed earth around the enclosure suppresses enclosure resonance for improved
low-frequency definition. The IGS212’s enclosure features drainage channels to drain
water that may enter the enclosure via the bass vents.
Placement and Sound Quality
1In-ground Installation
and Connection of
IGS212 Subwoofer
Speaker cables from the amplifier to the
subwoofer may be directly buried provided
you use direct burial-rated stranded speaker
cable. We highly recommend the use of a
1” to 1-1/2” ID conduit to protect the wires
from degradation and damage due to exca-
vation or normal gardening activities. The
NEAR IGS212 subwoofer has entry and exit
wire/conduit channels on the bottom of the
enclosure. We highly recommend the use
of the NEAR IE1 junction box.
*OPTIONAL: ORDER SEPARATELY
UNDERSIDE
VIEW OF
THE IGS212
SUBWOOFER
SPEAKER
INPUT
CABLE
CONDUIT
CHANNEL
*IE-1 DIRECT BURIAL
JUNCTION BOX
*IE-1
DIRECT BURIAL
JUNCTION BOX
FEED FROM
AMPLIFIER
Remove Pre-Installed
Jumpers (2X)
Connections using the
NEAR IE1 Junction Box
DETAIL
A
SPEAKER INPUT CABLE
BLACK
(COMMON)
RED
(POSITIVE)
FROM
AMP
(
+
)
Model IGS212
Subwoofer Features
1. Two (2) 12-inch diameter Metal Alloy
Diaphragm Woofers (Internally)
2. High-Density reinforced
enclosure with UV inhibitors
3. Low turbulence output vents (3)
with protective screens
5. Input Connection Cable
4. Wiring/Conduit Channels
(underside)
2
3
1
SIDE VIEW
ABOVE
VIEW
UNDERSIDE
VIEW
4
5
FROM SPEAKER
(
+
)(
-
)
(
-
)
SPEAKER
INPUT CABLE