BOLDR KELVIN User manual

1
BOLDR KELVIN USER MANUAL
BOLDR SHOPBOLDR.COM
KELVIN
KELVIN
USER MANUAL

2
BOLDR KELVIN USER MANUAL
To get started with the KELVIN heater scan the QR code below. It
contains video set up instructions as well as links to both IOS and
Android apps. Please note that we do not recommend the use of
KELVIN heater without the accompanying app.
KELVIN SPECIFICATIONS
KELVIN Standard
Weight: 9kg
Dimensions: 960 x 500 x 12mm
Advised Heating Area: 100 sqft (9m2)
Rated Input: 450W
WiFi Operational Range: up to 50m outdoors/30m indoors
KELVIN Large
Weight: 12kg
Dimensions: 1200 x 600 x 12mm
Advised Heating Area: 200 sqft (18m2)
Rated Input: 750W
WiFi Operational Range: up to 50m outdoors/30m indoors.
Wi-fi Requirments: Works with standard 2.4Ghz Bandwidth!*
*You will need a standard 2.4 ghz Wi-Fi bandwth . If your router has band
steering, we advise that you uncouple the 2.4 ghz and 5.0 ghz networks. This can
easily be done by logging into your Wi-Fi router IP address!
INTENDED USE
• Before utilizing the product, the user should determine the
suitability of the product for its intended use. The product is
intended for use as a heating device for residential use as
outlined in this document. Use outside of this scope is NOT
covered by the warranty.
• KELVIN heaters are intended for use with a specific voltage
which is region based. The voltage that is needed is based on
the delivery address. If the heater is used in a different region
than the delivery address - there are risks of overheating and
damage.
• Region specific voltages:
USA: 110V/120V
Canada: 110V/120V
UK: 240V
Europe, Ireland: 230V
Australia, New Zealand: 230V/240V
South Africa: 230V
Switzerland: 230V
Japan: 100V
• In no case shall Baldr Group Ltd (BOLDR) be liable under
any legal theory, including but not limited to contract or
strict liability, for any direct, indirect special, incidental or
consequential damages resulting from incorrect product use.
DOWNLOAD THE
BOLDR APP
https://linktr.ee/boldrkelvin
VIEW DRILLING
INSTRUCTIONS FOR
KELVIN INSTALLATION
Note: physical drilling template is included in the box.
https://linktr.ee/kelvin_drilling

3
BOLDR KELVIN USER MANUAL
SAFETY ADVICE
• CAUTION! Danger of electrocution. Mounting/installation is
recommended to be done by a qualified professional.
• CAUTION! At no point should the product be disassembled.
Opening the product control box will violate the warranty
and may lead to malfunction and danger to life.
• CAUTION! There is always risk of injury from touching any
form of electric heater and KELVIN panels are no different.
However, a key benefit of KELVIN panels, unlike conventional
heaters, is that they can be mounted higher up on walls -
reducing the likelihood of accidentally touching them or falling
against them. We always advise mounting panels higher on
the wall, especially in areas where young children or the
elderly are present.
• CAUTION! Connect and install the device only in the way
shown in these instructions. Any other method could cause
damage, injury and/or risk to life.
WHERE TO PLACE THE HEATER
• This is an infrared panel heater. It heats objects by transferring
energy directly from the heater into the object. Therefore,
consider placing the heater where it will not be immediately
obstructed by objects like furniture or where it cannot
effectively radiate out, such as at the edge or in the corners of
a room.
• Heater placement should be guided by the most actively used
areas in a room.
• Objects placed in front of the heater will heat up and can
prevent effective heat dispersion into the room. Avoid placing
the device opposite windows or open doorways.
• The mounting location should be chosen in such a way that the
glass cannot be accidentally broken and people will not be in
danger from a possible break in the glass.
• The minimum distance from the back side of the panel must be
30mm to the mounting surface. This will always be the case if
the mounting hardware provided is used.
• Objects in front of the panel must be at least 400mm away
from the sides. The distance between the sides of the heater
and the sides of any adjacent heater must be a minimum of
800mm. Failure to do so could cause excess heat to build up
behind the heaters and will void the warranty.
SHELLY THERMOSTAT
To enable the Shelly Thermostat follow the in-app instruction.
Battery Type: 3V DC - CR123A
Battery Life: Up to 18 months
Electrical consumption: Static ≤70uA/Awake ≤250mA
Humidity measurement range: 0~100% (±5%)
Temperature measurement range: -40°C ÷ 60 °C (± 1°C)
Working temperature: -40°C ÷ 60 °C
Dimensions (HxWxL): 35x45x45 mm
Radio protocol: WiFi 802.11 b/g/n
Frequency: 2400 – 2500 MHz;
Operational range: up to 50m outdoors/30m indoors
• CAUTION! Use the device only with batteries which comply
with all applicable regulations. Inappropriate batteries may
cause a short circuit in the device, which may damage it.
• CAUTION! Do not allow children to play with the device,
especially with the Power Button. Keep the devices for remote
control of KELVIN (mobile phones, tablets, PCs) away from
children.
• Device Wake Up: To open the device, twist the top and
bottom part of the case counter clockwise. Press the Button.
The LED should flash slowly. This means that Shelly thermostat
is in AP mode. Press the Button again and the LED will turn off
and Shelly thermostat will be in sleep mode.
LED States:
• LED flashing quickly - AP Mode
• LED flashing slowly - STA Mode (No Cloud)
• LED still - STA Mode (Connected to Cloud)
• LED flashing quickly - FW Update (STA mode
connected Cloud)
Factory Reset: You can return your temperature sensor to its Factory
Settings by pressing and holding the button for 10 seconds. Upon
successful factory reset the LED will flash slowly.
Wi-fi Requirments: Works with standard 2.4Ghz Bandwidth!*
*You will need a standard 2.4 ghz Wi-Fi bandwth . If your router has band
steering, we advise that you uncouple the 2.4 ghz and 5.0 ghz networks. This can
easily be done by logging into your Wi-Fi router IP address!

4
BOLDR KELVIN USER MANUAL
INSTALLING YOUR KELVIN
HEATER ON THE WALL:
• ATTENTION: When mounting the heater, beware that it will
shift when locking into place. Please keep this in mind when
positioning the heater.
• Attach the template to the wall in the position that you intend
to hang the heater ensuring the template itself is level.
• Drill the 4 holes as indicated on the template using an 8mm
diameter sized drill bit.
• Remove the template from the wall.
• Insert raw plugs and screw in supplied mounting screws,
leaving the screw head and 4 - 5mm of screw shaft exposed
(to mount the brackets on).
• The heater can now be affixed to the wall using the installed
screws by aligning the screw head with the holes on the
heater wall mount.
INSTALLATION SAFETY
• This appliance must be disconnected from its power source
during installation or service activities.
• In order to avoid overheating and potential fire hazard,
DO NOT cover the heater with insulating material or similar
material under any circumstances. DO NOT locate the
heater within 0.3m of any flammable materials (eg. Furniture,
curtains).
• The recommended minimum distance of the panel to the floor
should be 1.2m, especially if there are children at home.
• The space between the rear of the panel and the wall must be
unobstructed at all times to allow sufficient air flow.
• NEVER mount the heater where there is a risk it could fall into
any kind of water container.
• DO NOT install in rooms where direct contact with water is
possible.
• If your electric supply exceeds 250 Volts, DO NOT USE the
heater under any circumstances.
• CAUTION: the electrical circuit to power the heater must be
capable of disconnection and de-activation by a switch, fuse,
RCD or GFCI.
• DO NOT operate the heater if the cord or plug is damaged
or after the heater malfunctions, or if it has been dropped or
damaged in any manner. Check each heater for damage
before installation. Make sure that the heater itself, the plug
and the cable are free of any visible signs of damage. If the
cord is damaged the appliance must be sent for repair to the
manufacturer (Baldr Group Ltd).
• Handle carefully and avoid stressing the glass mechanically.
Do not use the heater if the glass panels are damaged.
Disconnect the heater and do not put it into operation again.
Dismount the heater immediately to reduce the danger of
direct impact from falling pieces and dispose of the unit
in accordance with the local Waste Electrical Equipment
regulations.
• This heater must only be used for the heating of people or
buildings. The heater is not to be used by children or persons
with reduced physical, sensory or mental capabilities, or lack
of experience or knowledge. Children should be kept away
and should not be left unsupervised around the unit.
• All operators should only switch on/off the appliance
provided that it has been placed or installed in its intended
operating position in accordance with these instructions.
Children must not plug in, switch on or regulate the appliance
or perform user maintenance including cleaning.
• DO NOT touch the heater when in use. The product has a
surface temperature of around 90°C and prolonged contact
with the heater will cause burns and injury.
• IMPORTANT: The heater must be mounted on a non-
flammable surface that is capable of bearing the weight of
the heater.
CLEANING
• Before attempting to clean the panel, unplug the heater, isolate
the unit from the electrical supply and allow it to completely
cool down. DO NOT immerse the KELVIN in water or splash
water onto it. Clean the glass surface with a damp cloth and
glass cleaner. Never use a wet cloth. When clean, dry the
surfaces with a dry cloth.
• DO NOT apply abrasive materials, solvents or solvent wipes
to the surface as this can cause irreparable damage. Wait until
the unit is completely dry before use.
MAINTENANCE & REPAIR
• DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void your
warranty. Repairs must only be carried out by an authorised
BOLDR service partner or the manufacturer (Baldr Group Ltd).

5
BOLDR KELVIN USER MANUAL
DISPOSAL
• The devices should not be disposed of with other household
waste at the end of it’s working life. Household users should
contact either the retailer where they purchased this product
for proper disposal or recycle them through the local return
system. For further information contact your municipal waste
management.
WARRANTY
• Within the warranty period, repair or replacement due to
defects in material and workmanship is completely free
of charge; the costs are covered by the manufacturer on
presentation of your invoice or delivery slip.
• A prerequisite for validity of the warranty is use of the device
as intended with observance of the specified conditions of
use. Any further warranty or claims are excluded. The warranty
covers the repair or replacement of the defective product only.
Any further claims or liability for consequential loss
are excluded.
• WARRANTY RESTRICTION: The warranty will be void if
the heater has been tampered with or opened in any way.
Baldr Group Ltd will assume no responsibility for scratches
on surface or frames after first use. Baldr Group Ltd cannot
accept responsibility for damage, loss or injury caused by
ingress of water or moisture, accidental damage, mishandling,
external impact, adjustment by unauthorised personnel
or failure to follow the correct maintenance and safety
precautions as stated in the manual.
• If a fault or defect covered by the warranty occurs, the heating
panel has to be sent to an authorised service partner or the
manufacturer together with the invoice or original delivery
note. If sending by carrier the heating panel should be
properly packaged and proof of purchase must be produced.
PRODUCT CERTIFICATION
• CE- European Safety Standards Low Voltage Directive
2014/35/EC
• EMC Directive 2014/30/EC
• RoHS 2011/65/EC Ecodesign requirements for local space
heaters 2009/125/EC.
• IP44 rated
LEGAL
Manufacturer: Baldr Group Ltd
Trading Name: BOLDR
Address: 71-75 Shelton Street, Covent Garden,
London WC2H 9JQ, UNITED KINGDOM
E-mail: [e-mail]
Website: https://www.shopboldr.com
Changes in the contact data are published by the manufacturer at
the official website of the device: https://www.shopboldr.com
The user is obliged to stay informed for any amendments of
these warranty terms before exercising his/her rights against the
manufacturer.