TradeQuip 1097T User manual

About the TradeQuip brand
The 'TradeQuip' brand of workshop equipment, is designed for use in a demanding workshop
environment by professional users. With proven and trusted “Made for the
Trade” reliability, 'TradeQuip' branded products offer the very best in performance for an
affordable price. All backed by a 1year trade guarantee across 1,000+ distributors Australia wide.
03/21 Product Code: 1097T
Made in China to TQB Brands Pty Ltd specifications Page 1
Visit us at www.tqbbrands.com.au
Product Code: 1097T
WORKSHOP HEATER
Specifications:
•Power Output: 50kW - 170,600 Btu/h
•Motor: 240V/50Hz 340W
•Noise Level: 77dB(A)
•Air Delivery: 1100 cubic metres per hour
•Fuel Consumption: 4kg per hour
•Tank Capacity: 56 Litres
•Dimensions: 1090 x 490 x 585mm
•Nett Weight: 27kg
•Carton: 1046 x 465 x 570mm
•Gross Weight: 31.8kg

03/21 Product Code: 1097T
Made in China to TQB Brands Pty Ltd specifications Page 2
Visit us at www.tqbbrands.com.au
WARNING
IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE
WARNING
The instructions and warnings contained in this manual should be read and understood before using or operating this equipment.
Do not allow anyone to use or operate this equipment until they have read this manual and have developed a thorough
understanding of how this equipment works. Failure to observe any of the instructions contained in the manual could result in
severe personal injury to the user or bystanders, or cause damage to the equipment and property. Keep this manual in a
convenient and safe place for future reference.
Whilst every effort has been made to ensure accuracy of information contained in this manual, the TQB Brands Pty Ltd policy of
continuous improvement determines the right to make modifications without prior warning.
CONTENT
WARNING............................................................................................................................................................................................ 2
CONTENT............................................................................................................................................................................................. 2
STANDARD OPERATING PROCEDURE ................................................................................................................................................. 3
ASSEMBLY, OPERATION, PREVENTITIVE MAINTENANCE.................................................................................................................... 4
TROUBLESHOOTING............................................................................................................................................................................ 7
PARTS LIST & DIAGRAM...................................................................................................................................................................... 8
WARRANTY ......................................................................................................................................................................................... 9

03/21 Product Code: 1097T
Made in China to TQB Brands Pty Ltd specifications Page 3
Visit us at www.tqbbrands.com.au
STANDARD OPERATING PROCEDURE
DO NOT use this equipment unless you have been trained and assessed to a competent level in its sate use and operation,
and have been given permission to use this
PRE-OPERATIONAL SAFETY CHECKS
Please read the following very carefully as failure to comply may invalidate your guarantee. When using electrical appliance
basic precautions should always be followed including below:
•The use of gasoline is strictly prohibited. It is a highly volatile fuel that can result in explosions or uncontrolled fires. It is
essential that only kerosene or diesel is used in this unit.
•If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal
injury or loss of life.
•Service must be performed by a qualified service agency.
•Unvented workshop heaters use air (oxygen) from the area in which it is used. Adequate combustion and ventilation air must
be provided. Refer to instructions.
•DO NOT store or use gasoline or other flammable vapours and liquids in the vicinity of this or any other appliance.
•Fire, burn, inhalation, and explosion hazard. Keep solid combustibles, such as building materials, paper or cardboard, a safe
distance away from the heater as recommended by the instructions.
•DO NOT use the Workshop Heater in spaces which do or may contain volatile or airborne combustibles, or products such as
gasoline, solvents, paint thinner, dust particles or unknown chemicals.
•Direct-fired heaters may cause carbon monoxide (CO) poisoning when incorrectly used, e.g. indoors without adequate air
circulation, or if not properly working. CO poisoning may lead to death.
•Failure to comply with the precautions and instructions provided with this heater, can result in death, serious bodily injury
and property loss or damage from hazards of fire, explosion, burn, asphyxiation, carbon monoxide poisoning, and/or electrical
shock.
•DO NOT use for home or recreational use.
•Please read these instructions before you operate this Workshop Heater
•The electrical system to which the appliance is connected must comply with current legislation. Installation requires a residual
current circuit breaker in the main electrical distribution board.
•Unplug the appliance before performing any maintenance operations.
•Always check the power cable before using the appliance. It must not be bent, taut, stretched, crushed or any way damaged.
•The power cable must be replaced by qualified personnel only. Use an original power cable only with a 3-pin approved plug.
•DO NOT touch the front outlet is very hot during operation due to high heat.
•When servicing, use only TradeQuip identical replacement parts. Use of any other parts will void the warranty. Ensure the
Workshop Heater is disconnected from power before servicing.
•Use the right product for the job. There are certain applications for which the Workshop Heater was designed. Do not modify
the Workshop Heater and do not use the Workshop Heater for a purpose for which it was not intended.
INTENDED USE
Ideal for space heating, frost protection and condensation control in commercial and industrial workshops, factories, and
warehouses.
DO NOT tilt the unit
DO NOT operate the unit with wet or damp hands

03/21 Product Code: 1097T
Made in China to TQB Brands Pty Ltd specifications Page 4
Visit us at www.tqbbrands.com.au
ASSEMBLY, OPERATION, PREVENTITIVE MAINTENANCE
1. FEATURES
TradeQuip "Made for the Trade" Direct-Fired Forced Air Workshop Heaters are ideal for workshops, garages and warehouses,
reducing concrete freeze and emergency heating. Ideal for quickly and efficiently heating cold condition workshops, this
forced air heater can be used in a variety of commercial and industrial settings and is fueled by kerosene or diesel. It is a
reliable heating solution for a cold work space and is easy to move and position as required thanks to the ergonomically
designed inbuilt handle.
2. ASSEMBLY
Unpacking: after removing the packing material, make sure the product is in perfect condition and that there are no visible
damaged parts. The packaging materials (Polyethylene bags, polystyrene etc.), must be disposed of in an appropriate refuse
collection container. Recycle cardboard.
1. To assemble the heater, proceed as follows:
2. Insert the wheel shaft J to the corresponding hole of feet pipe E，insert the cotter K to the corresponding holes; put plain
washer I to the two sides of shaft, slide the wheel H over the wheel shaft J，screw the nut G to fix the wheel on the shaft.
3. Put the heater body on the feet pipe assembly, make sure the 4 holes of handle A point towards the corresponding 4
holes on the feet pipe respectively.
4. Using the screw B, spring washer C, plain washer D and nut F to fix the feet pipe assembly and handle to the tank.
Part
Description
Qty
A
Handle
1
B
Screw
8
C
Spring washer
8
D
Plain washer
8
E
Feet pipe
1
F
Nut M5
8
G
Nut M12
2
H
Wheel
2
I
Plain washer ø12
2
J
Wheel shaft
1
K
Cotter
2

03/21 Product Code: 1097T
Made in China to TQB Brands Pty Ltd specifications Page 5
Visit us at www.tqbbrands.com.au
3. BEFORE USE
Prior to each use conduct a visual inspection by checking for abnormal conditions, such as cracked joins and damaged, loose,
or missing parts.
1. Position the Workshop Heater on a flat, level, non-flammable, solid surface.
2. Direct-fired heaters are intended for use in outdoor open areas or in indoor well ventilated areas. For indoor use, provide
permanent ventilation openings of at least 25 cm²/kW, equally distributed between floor and high level, with a minimum
of 250 cm².
3. Only install the Workshop Heater in normal upright position.
4. Do not place the heater near walls, corners or low ceilings.
5. Do not place the heater below a socket outlet.
6. Do not place the heater on moving vehicles or where it can tip over.
7. Keep the heater away from flammable, combustible, explosive or corrosive materials.
8. Keep the heater away from curtains or similar materials that could block the air inlet and outlet.
9. Never block or restrict the air inlet and outlet for any reason.
10. Keep the power cable away from heat sources, sharp edges, cutting and moving parts.
11. Do not expose directly to the weather or to excessive humidity.
12. Do not place the heater in the immediate surroundings of a parts washer, shower or cleaning bath.
13. Follow general and special fire safety regulations in force in all fields of applications. In any case ensure the following
minimum safety clearances from materials or objects in the surroundings of the heater:
•Side: 0.6 m
•Air inlet side: 1 m
•Top: 1.5 m
•Hot air outlet side: 3 m
•Floor: 0 m
14. Floors and ceilings must be made of fireproof materials in the place where the heater is operated.
15. Do not connect direct-fired heaters to air ducts.
4. OPERATION
START UP:
1. Fill tank with clean fuel. Only use Diesel or Kerosene.
2. The fuel gauge on top of the tank allows to check fuel level
3. Connect the power cord plug to a 240V 50 Hz earthed electrical supply system.
4. Earthing is mandatory.
When above “start-up” complete, the left display window shows “--”, the right display window shows ambient temperature
value.
1. Push the power switch to “ON” position.
2. The default temperature setting is 20℃, be showed on the left display window.
3. If the ambient temperature is lower than default temperature, the electrodes start sparking, after 7 seconds, the heater
starts.
4. If the ambient temperature is higher than default temperature, turn thermostat control knob to desired temperature,
the electrodes start sparking, after 7 seconds, the heater starts.
COLD START-UP:
At low temperature keep the air vent hole closed by a finger during ignition to make start-up easier.
ABNORMAL OPERATION:
In the event of a malfunction (flame failure, reduced air flow, bad combustion, etc.) the heater stops and the indicator light
starts FLASHING (THE LOCK-OUT MODE code will be showed on the display window).
Minimum Opening Size
1097T
1250 cm²

03/21 Product Code: 1097T
Made in China to TQB Brands Pty Ltd specifications Page 6
Visit us at www.tqbbrands.com.au
MANUAL RESET/RESTART:
If the heater is in lock-out mode, check and remove the cause of lock-out before restarting the heater. To reset, turn the
ON/OFF switch to 0 and then again to I. In case of repeated malfunction, call technical service. Turning the thermostat control
knob will NOT reset the heater.
SHUT-DOWN
1. Move switch to "OFF" (O) position. Unplug the unit when not used for a long time.
2. Never disconnect the heater from mains to stop it while in operation. Always allow the cooling sequence to be
completed otherwise the residual heat could damage internal components.
3. Do not cover the heater. Do not block the air inlet and outlet.
4. The heater outlet is very hot during operation and after use. Do not touch! Use personal protecting equipment if
needed.
5. Children should be supervised to ensure that they do not play with the appliance.
6. The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge.
7. Unplug the heater before moving it. Never pull the cable to unplug or move the unit.
8. Do not leave the heater unattended when in use.
9. Never use the appliance with wet hands or when either the heater or the power cable is wet.
10. If the supply cable is damaged, it must be replaced by the manufacturer, by a service agent or a similar qualified
person.
5. STORAGE
TradeQuip Workshop Heaters should always be stored in a dust free dry location on a level surface.
6. MAINTENANCE
Disconnect power prior to any maintenance. Before starting any maintenance task, shut down, unplug and let the heater cool
down for at least 15 minutes.
•Regularly wipe the enclosure using a soft sponge or cloth. For very dirty parts, use a damp sponge of lukewarm water
and a mild detergent, then dry using a clean cloth.
•Keep air inlet and fan free from dust and dirt. To clean inner parts, gently blow compressed air through air inlet.
•Regularly inspect the power cable: if worn, cracked or damaged have it replaced by technical service.
•Before storing the heater, make sure it is perfectly cool and dry. Cover the unit with a plastic bag, put it in its packing box
and store it in a dry, ventilated place.
•Do not attempt any electrical repair yourself. If the heater needs service or repair, contact a qualified technician.
•Do not use a faulty unit unless a qualified technician has inspected and repaired it.
•When cleaning, make sure that water does not enter the unit.
•Do not open the enclosure to clean the inner parts. Do not spray water into the heater.
•Never use solvents, gasoline, toluene and similar aggressive chemicals to clean the heater.
7. SERVICE & REPAIR
Any TradeQuip Workshop Heaters found damaged in any way, or found to be worn or operated abnormally, should be
removed from service until repaired by an authorised service agent. Owners and / or operators should be aware that repair
of this product may require specialised equipment and knowledge. Only authorised parts, labels and decals shall be used on
this equipment. Annual inspection of the Workshop Heater is recommended and can be made by an authorised repair facility
to ensure that your equipment is in optimum condition and that the equipment has the correct decals and safety labels
specified by the manufacturer.

03/21 Product Code: 1097T
Made in China to TQB Brands Pty Ltd specifications Page 7
Visit us at www.tqbbrands.com.au
TROUBLESHOOTING
PROBLEM
CAUSE
REMEDY
Motor does not start
E1 displayed on the screen
No power or low voltage
Check power cable and voltage
Check fuse and replace if necessary
Faulty or damaged power
cord
Check and replace if needed
Faulty motor/capacitor
Check and if necessary replace
Lock-out of appliance due to
previous overheating
Detect the cause of overheating
Shut the appliance down
Check air inlet and outlet
Wait some minutes and restart the appliance
E2 displayed on the screen
The temperature probe has
faulted or the connector for
temperature probe is loose
Check and replace the temperature probe if needed
Check and replace the PCB if needed
Motor runs, but the heater does
not ignite and locks out after a
short time
E1 displayed on the screen
Empty fuel tank, dirty or
wrong fuel
Remove wrong or dirty fuel
Fill the tank with clean Diesel or kerosene
Fuel filter clogged
Clean or replace fuel filter
Air leaks in oil line
Check hoses, tighten connections, if necessary replace
Burner nozzle clogged
Clean nozzle with compressed air, replace if necessary
Fuel viscosity increased at
low temperature
Mix Diesel with 10-20% kerosene
Flames come out of flue outlet
E1 displayed on the screen
Insufficient airflow into
combustion chamber
Check air inlet, fan, motor
Compressor pressure too
high
Check air pressure, adjust if needed*
Heater stops during operation
Ambient temperature displayed
on the screen
The room temperature set
on room thermostat has
been reached
Normal operation
To start turn the temperature control knob clockwise on a
higher setting
Heater stops during operation
E1 displayed on the screen
Flame failure
Check and remove the cause(s) of malfunction
To reset, turn On/Off switch to 0 and then to I
Call technical service if the problem persists
Bad combustion
Reduced airflow
Overheating

03/21 Product Code: 1097T
Made in China to TQB Brands Pty Ltd specifications Page 8
Visit us at www.tqbbrands.com.au
PARTS LIST & DIAGRAM
Part
Description
Qty
Part
Description
Qty
1
Oil Drain Seal
1
30
Burner Support Plate
1
2
Oil Drain Screw
1
31
Photocell Assembly Bracket
1
3
Fuel Tank
1
32
Photocell Assembly
1
4
Power Cord
1
33
Thermostat Bracket
1
5
Cable Fastener
1
34
Combustion Chamber Blade
2
6
Ignition Transformer
1
35
Reset Thermostat
1
7
Bracket
2
36
Burner Head
1
8
Fuel Filter Assembly
1
37
Nozzle Assembly
1
9
Sealing Ring
1
38
Nozzle Adaptor
1
10
Breather Cover
1
39
Gas Hose
1
11
Fuel Tank Cap
1
40
Oil Hose
1
12
Sealing Ring
1
41
Ignition Needle
1
13
Tank Cap Shaft
1
42
High Voltage Cable
2
14
Oil Inlet Filter Holder
1
43
Solenoid Valve
1
15
Oil Inlet Filter
1
44
Solenoid Valve Bracket
1
16
Oil Leveller
1
45
Air Inlet Grille
1
17
Thermostat Knob
1
46
Motor Support
1
18
Thermostat Knob Nut
1
47
Motor Assembly
1
19
Display Window
1
48
Fan
1
20
Display PCB2
1
49
Top Cover
1
21
On/Off Switch
1
50
Side Plate
1
22
Control Panel
1
51
Wheel Axle
1
23
PCB Support
1
52
Feet Pipe
1
24
Power PCB1
1
53
Cotter Pin
2
25
Bottom Cover
1
54
Wheel
2
26
Front Cover Assembly
1
55
Flat Gasket
2
27
Chamber Shield Bracket
4
56
Screw Nut
2
28
Combustion Chamber Shield
1
57
Steel Pipe Plug
2
29
Combustion Chamber
1
58
Handle
1

03/21 Product Code: 1097T
Made in China to TQB Brands Pty Ltd specifications Page 9
Visit us at www.tqbbrands.com.au
WARRANTY
TradeQuip products have been carefully tested and inspected before shipment and are guaranteed to be free from defective
materials and workmanship for a period of 12 months from the date of purchase except where tools are hired out when the
guarantee period is ninety days from the date of purchase.
Should this piece of equipment develop any fault, please return the complete tool to your nearest authorised warranty repair
agent or contact TQB Brands Pty Ltd Warranty team –warran[email protected].
If upon inspection it is found that the fault occurring is due to defective materials or workmanship, repairs will be carried out free
of charge. This guarantee does not apply to normal wear and tear, nor does it cover any damage caused by misuse, careless or
unsafe handling, alterations, accident, or repairs attempted or made by any personnel other than the authorised TQB Brands Pty
Ltd repair agent.
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised.
Your TQB Brands Pty Ltd guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your
proof of purchase within the 12 month period.
Consumer Guarantee
Our goods come with a guarantee that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have
the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
All images and illustrations shown are for reference purposes only. All information, specifications and illustrations in this manual are based on
the latest information available at the time of publication and are subject to change without notice. The information in this manual is periodically
revised to ensure the latest information is included. Download the latest version of this manual and other related technical documentation from
www.tqbbrands.com.au