Bolin Technology Dante AV D20H User manual

Dant
eAV Decoder
TM
Version 2.0
Quick Start Guide
Dante AV
™Encoder / Decoder

This quick start guide applies to D20H, D20S
1
D20H/D20S
Dante AV Encoder/Decoder
Items included in the encoder / decoder box
1 2 3 4 5
VCC-CC45RS
RJ45 to RS422
Control cable x 1
Optional Accessories
B-RM10
Single Rack Mounting Kit-
For Encoder / Decoder
Note:
The Dante AV Decoder is mandatory for Dante AV video output.
Power Adaptor x 1
Power Cord x 3
(Type: US, EU, UK)
M4*6PW Screw x 8 M2.5*3C Screw x 8 M3*8K Screw x 4 M5*12P Screw x 4
8*300mm
Cable Tie x 4 HDMI Cable Mount x 1
Base Mount Kit x1
Surface Mount Kit x 1 For Surface Mount Kit mounting For HDMI cable secure mounting For base mount kit mounting For TV surface mounting
Mini Pole Bracket x 1
For Encoder / Decoder
Dual Rack Mounting Kit-
Dante AV Video Output Setup
1. Item List
HDMI 2.0 Cable x1
(Not Included)
Cat6 Network Cable x3
Dante AV Encoder x1 Display Output Device x 1
(Supports 4K60 )
POE++ 1Gbps Network Switch
(Not included)
Computer
Dante Controller x 1
2. Install Dante Controller Software
Dante Controller Download URL:https://my.audinate.com/support/downloads/download-latest-dante-software?lang=zh-hans
Dante Controller Hardware Requirements:
CPU: Minimum of 1GHz processor
Storage: At least 512MB
Network Card: Ethernet connectivity port (1000 Mbps)
Dante Controller OS Requirements:
(Not Included)
(Not included) (Not included)
Dante AV Decoder x1
Bolin 97W POE power supply-
For Camera and Encoder / Decoder
DIN Rail Mounting Kit-
For Encoder / Decoder

MONITOR OUT
++
Encoder Decoder
HDMI OUT
ETHERNET 2 ETHERNET 1
DC-12V
HDMI IN
12-SDI
3. Connection Diagram
PTZ Camera HDMI Output
HDMI 2.0 Output
POE++ Switch
HDMI Display Output Device
Note: ①. DHCP network configuration is recommended.
② If network does not support DHCP, please manually configure IP details
on the camera and decoder to match the same gateway.
③ Switch Requirement:
· Nonblocking Layer 2
· Green Ethernet must be OFF (Recommend not using Green Ethernet capable switches)
· Use reputable "Managed" switches
· Support QoS with strict priority and 4 queues
· IGMP Snooping ON
· Please refer to product manual at www.bolintechnology.com for IP configuration instructions
①. Power Adaptor (DC 12V 4A) to power the decoder.
②.When using POE ++ , use IEEE802.3bt certified switch to power this decoder
4. Power on the Decoder
Both DC12V and POE are workable, when powering the camera, DC 12V preferably.
DC 12V 4A
For Dante AV camera startup tips, please refer to its respective diagram.
Note:
2
++
++
Two Ethernet ports available,
only Port 1 supports POE++.
12G-SDI Display Output Device
Only D20S Support12G-SDI Output
12G-SDI Cable x1(Not Included)
12G-SDI Output
USB2.0
(FW Upgrade Only)RS-232 RS-422
1 2 3
IR Select
IN OUT
Video
Format
Audio
HDMI MicroSD 6G/3G-SDI Genlock
LAN/PoE HDBaseT
DC-12V
MONITOR OUT
++
Encoder Decoder
HDMI OUT
ETHERNET 2 ETHERNET 1
DC-12V
HDMI IN
12- SDI
MONITOR OUT
++
Encoder Decoder
HDMI OUT
ETHERNET 2 ETHERNET 1
DC-12V
HDMI IN
12- SDI
HDMI Display Output Device
Dante AV Encoder
Dante AV Decoder
Dante
Controller
Network Cable
Network cable (POE++)Network cable (POE++)
Monitor out

Dante Controller Video - Network View
File Devices View Help
Routing Device Info Clock Status Network Status Events
P r i m a r y L e a d e rC l o c k : D 2 0 S - R X- 0 2 2 5 a 2 ?
F i l t e r T r a n s m it t e r s
F i l t e r R eo e i v e r s
Receivers(2)
_
+
D20H- TX- 02263C
D20S- RX- 0225 a2
Transmitters(2)
D20H- TX- 02263C D20S- RX- 0225 a2
x
_
+
+
+
+ +
5. Dante AV Decoder Startup
Switch on the decoder
after connecting the power
Green: Normal
Dante AV Decoder
TM
Green: Normal, Not lit: Abnormal/Error
Green: Not protected, Green (Blinking): Protected,Red: Abnormal/Error
:
Green: Normal, Yellow: Starting up, Red: Abnormal/Error
Green (Blinking): Normal, Red: Abnormal/Error
For Dante AV camera startup tips, please refer to its respective diagram.
Note:
6. Display Camera Video via Decoder
?
x
1. Click to choose network interface
This is mandatory when there are multiple
network connectivity methods on the device.
Configure Dante Interfaces in Unmanaged mode
Select the network interface that the Dante Controller
Use Shared Dante interface
Primary Interface:
Secondary Interface:
Ok
IP: 192.168.2.6
MAC: IC:IB:OD:7E:4C:3B
Network
None
IP: No Address
MAC: 00:00:00:00:00:00
N/C
3. Click to see specific transmitter routing options.
+
2. Click to see all connected Dante devices.
4. Click to see specific receiver routing options.
+
3
Green: Dante network clock slave, sync achieved
Green (Blinking): in sync with leader clock,Red: Abnormal/Error
1G

Dante Controller Video - Network View
File Devices View Help
Routing Device Info Clock Status Network Status Events
P r i m a r y L e a d e rC l o c k : D 2 0 S - R X - 0 2 2 5 a 2 ?
x
Device
Name
Sync Mute Clock
Source
Domain
Status
Primary
v1Multicast
Primary
v2Multicast
Secondary
v1Multicast
Secondary
v2Multicast
Dante
Dante
Follower
Leader
Disabled
N/A
N/A
Preferred
Leader
EnableSync
ToExternal
Disabled
N/A
N/A
N/A
N/A
N/A
N/A
D20H-TX-02263c
D20S-RX-0225a2
Dante Controller Video - Network View
File Devices View Help
Routing Device Info Clock Status Network Status Events
P r i m a r y L e a d e rC l o c k : D 2 0 S - R X - 0 2 2 5 a 2 ?
x
Device
Name
Model
Name
Product
Version
Dante
Version
Device
Lock
Primary
Address
Primary
LinkSpeed
Secondary
Address
Secondary
LinkSpeed
D20H-TX-02263c
D20S-RX-0225a2
Bolin D20H Encoder
Bolin D20S Decoder
3.1.2
3.1.2
4.3.6.10
4.3.6.10
192.168.2.154
192.168.2.155
1Gbps
1Gbps
N/A N/A
N/A N/A
5. In Device Info tab, all connected Dante devices are displayed, if the device is not listed
please check its network connectivity.
6. Select the Clock Status tab for clock leader. This is optional,
Dante Controller software will automatically select a leader if left undefined.
4
Dante Controller Video - Network View
File Devices View Help
Routing Device Info Clock Status Network Status Events
P r i m a r y L e a d e rC l o c k : D 2 0 S - R X- 0 2 2 5 a 2 ?
F i l t e r T r a n s m it t e r s
F i l t e r R eo e i v e r s
Receivers(2)
_
+
_D20H- TX- 02263c
D20S- RX- 0225a2
Transmitters(2)
D20H- TX- 02263c
x
_
_
+
_
_
_
D20S- RX- 0225a2
USB
IR
_
Seria l
Right Center
LeftC enter
Right Surroun d
LeftS urround
LFESo reen
Cente r
Right
Left
USB
IR
Seria l
USB
IR
SDI /HDMI RX
Seria l
Right Center
LeftC enter
Right Surroun d
LeftS urround
LFESo reen
Cente r
Right
Left
USB
IR
HDMI TX
Seria l
_
_8. Subscribe Audio TX (Left/Right) to Audio
RX (Left/Right), you can subscribe to the
left channel or the right channel, or you can
subscribe both
7. Check to subscribe TX to RXHDMI
connection route.

7. Camera Remote Control Setup
① Connection Diagram
PTZ Camera Cat 6 Network Cable,
POE++ Powered
A-RS422-B LAN/POE RS232
Cat6 Network Cable (POE++)
Group A
RS422 VISCA Port
PTZ Keyboard
Controller
(Optional)
Dante AV Decoder
++
USB2.0
(FW Upgrade Only)RS-232 RS-422
1 2 3
IR Select
IN OUT
Video
Format
Audio
HDMI MicroSD 6G/3G-SDI Genlock
LAN/PoE HDBaseT
DC-12V
Front Side
Back Side
MONITOR OUT
++
Encoder Decoder
HDMI OUT
ETHERNET 2 ETHERNET 1
DC-12V
HDMI IN
12-S DI
Front Side
Back Side
MONITOR OUT
++
Encoder Decoder
HDMI OUT
ETHERNET 2 ETHERNET 1
DC-12V
HDMI IN
12-S DI
RS422 VISCA Port
Dante AV Encoder
Cat6 Network Cable (POE++)
Cat6 Network Cable
ON
Note: The camera should be powered off prior to changing the DIP switch setting. When there are multiple PTZ cameras
involved, refer to the table above for unique VISCA address to each camera. Up to seven unique address can
be assigned to cameras at any given time.
② Camera VISCA Address, Communication Protocol, and Baud Rate Settings（Take BC-7 as an example）
Example: For VISCA ID 1 with RS422 Protocol and 9600 baud rate then
set the DIP switch (1-8) to ON, OFF, OFF, ON, OFF, ON, OFF, ON position.
OFF 4.RGB ON
YUV OFF
5
RX-
RX+
GND
-
-
-
TX-
TX+
1
2
3
4
5
6
7
8
Orange/White
Orange
Green/White
Blue
Blue/White
Green
Brown/White
Brown
1 2 3 4 5 6 7 8
RS422
RX-
RX+
GND
-
-
-
TX-
TX+
1
2
3
4
5
6
7
8
Orange/White
Orange
Green/White
Blue
Blue/White
Green
Brown/White
Brown
1 2 3 4 5 6 7 8
RS422

Note:
③ Subscribe Channel on Dante ControllerRS-422
Rs422 channel needs to be subscribed in the Dante controller for remote control. Please refer to the keyboard controller's
product manual for detail.
You can also use the infrared remote control to remotely control the camera through the DanteAV decoder.For detailed IR
remote operation instruction, please refer to camera product manual.
Dante Controller Video - Network View
File Devices View Help
Routing Device Info Clock Status Network Status Events
P r i m a r y L e a d e rC l o c k : D 2 0 S - R X- 0 2 2 5 a 2 ?
F i l t e r T r a n s m it t e r s
F i l t e r R eo e i v e r s
Receivers(2)
_
+
_D20H- TX- 02263c
D20S- RX- 0225a2
Transmitters(2)
D20H- TX- 02263c
x
_
_
+
_
_
_
D20S- RX- 0225a2
USB
IR
_
Seria l
Right Center
LeftC enter
Right Surroun d
LeftS urround
LFESo reen
Cente r
Right
Left
USB
IR
Seria l
USB
IR
SDI /HDMI RX
Seria l
Right Center
LeftC enter
Right Surroun d
LeftS urround
LFESo reen
Cente r
Right
Left
USB
IR
HDMI TX
Seria l
_
_
Check to subscribe
for controlRS-422
6

2082 TECHNOLOGY LLC dba
BOLIN TECHNOLOGY