Bomma Blimp BOM1105724 User manual

bomma Installation Manual for Wall Light Fixtures Installation Manual don’t throw away
blimp
Design by Big-Game

Introduction
• Please read this usage manual carefully prior to installation and follow its instructions
and recommendations.
• The installation of the wall light requires more than one person.
• For safety reasons, as well as for warranty purposes, it is forbidden to use this product in
conflict with this manual and for purposes other than those stipulated in this manual.
• Prior to mounting, use an appropriate circuit breaker to turn off electricity.
• All interventions regarding the wiring of the light fixture may only be carried out by a
qualified electrician.
• Prevent children or persons with lowered sensory or psychological abilities from handling
the light fixture, as it contains small and fragile pieces that could be dangerous when
inappropriately handled or ingested.
• The producer bears no liability for damage caused by improper installation.
• The dimensions and weight of glass parts may differ slightly, due to manual production.
• All Bomma products are made from hand-blown lead-free crystal. Any small bubbles,
non-melts and inhomogeneities in the glass are not a reason for complaint. This is a
characteristic feature of this traditional craft.
• The surface of the mounting may also include minor imperfections due to manual
production.
• The wall light is intended for interior lighting.
Components included in the package
• Hand-blown glass part of the light fixture
• Mounting
• Allen key
• Diffuser
• Dimmable light source
• Installation manual
• Maintenance instructions
• Gloves
Technical parameters, specifications
• Voltage rate: 220–240V / A.C. 50–60Hz
• Protection: IP 20
• Input rate: 1 x LED modul 24,5W / 700mA
• Weight: ~ 15,8 lb
• Size: dia. 17,7 inch, H 9,6 inch
• Class: I.
Recommended light source: LED modul 24,5W / 700mA
Recommended transformer: Mean well, LCM 40, 100 – 240V AC, 50 – 60 Hz, 700mA

1
Upon opening, first determine that there was no damage occurred during transport and
that the light fixture is complete. Otherwise, please contact your seller immediately, as
later claims may not be considered.
Assemble the lighting fixture according to the manual, recognizing that its installation
wiring may only be carried out by a qualified electrician following general legal
regulations.
Remove the screws 7and slide the mirror 3out of the mounting 2.
1
2
3
7

Slip the mounting 2on the incoming power supply cable and attach using appropriate
screws and wall-plugs, which are not included in the package. Select their size and type
according to the material of your wall and the weight of the fixture. Turn the mounting
before screwing in so that the lead-in hole for the supply conductor is at the bottom.
2
2

1
Install the wiring according
to the diagram.
3
L
N
PE
INPUT
OUTPUT
1
Attach the mirror 3to the inner
fins of the mounting 2using
two screws 7.
4
2
3
7

Screw the diffuser 5into the thread of the central part with the LED light source 4.
5
Attach the glass part 1by gradual
tightening the three screws 6on the
perimeter of the hoop 2. Gently bend the
glass and make sure it is firmly held in the
hoop
Congratulations! You may now reconnect
the power and turn the light on.
When dismantling, first turn off the light and
disconnect from the power supply. Then
follow the above steps in reverse order. Use
the original or similar packaging for possible
later transport of the light fixture to prevent
damage.
6
1
2
6
5
4

Maintenance
• When unpacking, installing and cleaning
your fixture, handle the individual
components with outmost care,
particularly the glass parts, which are
very fragile.
• Assembly and electric installation must
be carried out by certified electricians.
• Wall lights are intended for interiors.
• We recommend consulting the
installation and the anchoring of wall
lights in ceiling materials with your
project manager, technician or another
competent party.
• Do not cover nor touch the light source
while the light is on.
• Do not attempt any repairs or changes
to the components. Always contact our
specialized service.
• Spare parts that are not supplied or
approved by the producer may not be
used.
• The light source is tailor-made, so it
is not possible to buy an adequate
replacement freely. If a service change
is required, please contact us at info@
bomma.cz. If the light source is destroyed
due to incorrect electrical installation, it is
not possible to claim warranty for service
replacement.
• Do not expose the light fixture to
unsuitable environments where it could
become damaged (water, frost, heat).
• Ensure appropriate access (ladder,
scaffolding, aerial work platform) prior
to maintenance or cleaning wall lights,
in order to comfortably reach and safely
handle the light fixture.
• Note: in some areas, the lighting fixture
may have sharp edges that may cause
injury. Beware while in immediate
proximity of the fixture.
• Perform cleaning and all maintenance
with the light turned off, ideally entirely
disconnected. Respect this rule for the
entire duration of installation.
• We recommend hanging the fixture up
at sufficient height to avoid injury (e.g.
head injury) to persons moving within its
proximity.
• We recommend performing the
installation of wall lights with more than
one person.
• After installation check whether the light
fixture is properly set in its base.
• Do not expose the light to inappropriate
strain and protect it from mechanical
damage.
• When in operation, the light source
becomes hot. Prior to any handling, wait
for the light source to naturally cool down
and do not expose it to fast cooling.
• Do not hang any other components on
the light fixture, other than those listed in
the installation manual.
• Pay attention to checking all parts prior to
their installation. Damaged components
and glass parts (fragmentation, cracks)
may cause personal injuries to persons
moving within its proximity.
• Should any serious problem occur during
cleaning or maintenance, do not hesitate
to contact the producer.
• Any other handling of the wall light fixture
should be performed by a qualified
technician or directly by the producer.

Cleaning
• All cleaning and maintenance must be
carried out when the power is off, ideally
entirely disconnected.
• When cleaning, use fine-fabric gloves.
Particularly avoid handling metal-
coated crystal without gloves, to avoid
fingerprints and loss of gloss.
• Use soft cloths to clean metal parts. Such
parts may be cleaned with a dry cloth or
a cloth dampened in warm water with
a mild detergent. Avoid using solvents or
technical benzene to clean metal parts.
Avoid alcohol-based cleaners that may
cause changes of surface colors.
• Clean fine-steel surfaces with products
sold especially for this purpose.
• To clean the glass parts, use products in
concentrations recommended by their
producers. Immediately after cleaning,
dry the light fixture and hang it again.
• When cleaning glass parts, a
concentrate of 90% water and 10%
vinegar may also be used. Apply this
mixture with a clean spray-bottle. Put
on cotton gloves, apply the solution to
one of them and gently wipe the parts
requiring cleaning. Immediately dry the
cleaned surfaces with the other glove.
Give particular care to cleaning individual
parts of the light that cannot be
dismantled. Inappropriate handling may
cause loosening or chipping these parts.
• Avoid cleaning removable parts of the
light fixture in a dishwasher.
Important Notice
• The producer bears no responsibility
for damage cause by unprofessional
installation or inappropriate handling
of the light fixture, including installation
with accessories other than those
recommended by the producer.
• The producer bears no responsibility
for damage caused by unprofessional
interventions into the mounting and
safety features of the light fixture,
including damage to the product by
inappropriate power supply, storage
or use of the light fixture in a humid
environment.
• Do not place the light fixture in humid
environments, such as near a boiler or
other sources of water vapor. Do not
place the lighting fixtures in showers or
above bathtubs and never touch them
when you are in contact with water.
• The producer reserves the right to make
minor changes to the construction of the
light fixture without prior notice.

bomma.cz
Date of packagingControl
Disposal
Upon the completion of the technical working life of the light fixture and its disconnecting
from power supply, dismantle and separate the individual parts. Hand over the separated
parts to the appropriate organizations responsible for waste disposal.
Waste Materials Catalog
Number Category Name
10 11 11* N Waste glass
in small particles
and glass powder
containing heavy metals
10 11 12 O Waste glass other than those
mentioned in 10 11 11
17 04 01 O Copper, bronze, brass
17 04 05 O Iron and steel
20 01 01 O Paper and cardboard
15 01 05 O Composite packaging
Contact
Bohemia Machine Ltd.
1177 Zámecká St.
58291 Světlá nad Sázavou
Czech Republic
[phone]
[e-mail]
www.bomma.cz
Instagram bomma_cz
Facebook bommacz

Notes

step beyond