BOND MANUFACTURING Tank Hideaway 67635 Manual

Storage of this Tank Hideaway
TM
indoors is
PACKAGE CONTENTS
Hardware List
Item no. QTY
1 15
2 2
3 1
4 4
ASSEMBLY INSTRUCTIONS
Step 1: Assemble 2 pcs feet (M6x25) to panel A. Step 2: Assemble 2 pcs feet (M6x25) to panel B.
Step 3: Assemble panel A and B to bottom Step 4: Assemble panel C to panel A, B
frame using 4pcs M5x10 screws. using 6pcs M5 x 10 screws.
non-combustible surface such as concrete, rock or stone.
Item#:67635
! READ BEFORE USE AND KEEP FOR FURTHER REFERENCE
Tank Hideaway
TM
: Care and Use Instructions
This Tank Hideaway
TM
is intended for outdoor use only. Always place this Tank Hideaway
TM
on a hard, level,
Do not use near flammable or combustible objects
or materials.
permissible only if the tank is disconnected and
This Tank Hideaway
TM
must be used ONLY in a well-ventilated
space and shall not be used inside a building or garage.
This Tank Hideaway
TM
is designed for use with a 20 lb. liquid
properly stored outdoors. propane gas (LP) tank (not included).
This Tank Hideaway
TM
is not to be installed or
used in or on recreational vehicles and/or boats.
when in the vicinity of this Tank Hideaway
TM
.
Young children should be carefully supervised
M6X30 Screw
Do not attempt to transport this Tank Hideaway
TM
with a gas tank
installed.
SPECIFICATION
Minimum clearance from Tank HideawayTM to appliance which is used with the Tank HideawayTM together and
other heat sources is 48"(121.9cm).
Do not sit or rest feet on this Tank Hideaway
TM
.
M5X10 Screw
M8X30 Wing Screw
M6X25 Feet
1

Step 5: Assemble panel D to panel A, B Step 6: Assemble panel E to panel B
using 5pcs M5 x 10 screws. using 2pcs M6 x 30 screws.
Step 7: Put a 20 lb. liquid propane Step 8: Turn the wing screw (M8X30) on the
gas (LP) tank (not included) in the outer part of metal stand clockwise to
metal stand. Make sure the gas tank secure the gas tank tightly.
sits on the metal stand completely.
Step 9: Put the regulator inside the Step 10: Connect the regulator to gas tank.
Tank Hideaway
TM
, and the hose through the
hole at the bottom of the Tank Hideaway
TM
.
Patent Pending
**WARNING**
1700 West 4
th
Street, Antioch, CA 94509
1-866-771-BOND(2663) OR TO BETTER
EXPEDITE YOUR REQUEST FEEL FREE TO EMAIL US
customer.service@bondmfg.com
OR VISIT OUR WEBSITE UNDER CUSTOMER SERVICE SUPPORT
www.bondmfg.com
BOND MANUFACTURING CO.
Open Tank Hideaway
TM
cover to connect or disconnect your regulator and to open/close the tank valve.
Make sure the hose is not pressed underneath the Tank Hideaway
TM
.
IF YOU HAVE QUESTIONS OR CONCERNS
PLEASE CALL BOND TOLL FREE #
2

El almacenamiento en interiores de este Tank Hideaway
MR
CONTENIDO DEL EMBALAJE
Lista de herrajes
CANT.
15
2
1
4
INSTRUCCIONES DE MONTAJE
Paso 1: Junte 2 patas (M6X25) al panel A. Paso 2: Junte 2 patas (M6X25) al panel B.
Paso 3: Junte los paneles A y B a la montura Paso 4: Junte el panel C a los paneles A y B
inferior utilizando 4 tornillos M5X10 utilizando 6 tornillos M5X10.
Distancias libres mínimas del Tank HidewayMR al aparato utilizado con el Tank HidewayMR y a otras fuentes de calor: 121.9cm (48").
DESCRIPCIÓN
Tornillo M6X30
No. de artículo
Tornillo mariposa M8X30
Patas M6X25
3
4
Tornillo M5X10
No trate de transportar este Tank Hideaway
MR
con una bombona de
gaz instalada.
almacenada correctamente en exteriores.
Se debe bien vigilar a los niños cuando están cerca de este
1
2
Tank Hideaway
MR
.
No siéntese ni apoye los pies sobre este Tank Hideaway
MR
.
gas propano líquido (GPL) de 9 kg (20 lb) (no proporcionada).
No se debe instalar ni utilizar este Tank Hideaway
MR
en vehículos recreativos y (o) barcos.
plana y no combustible como el concreto, la piedra o la roca.
Hay que utilizar este Tank Hideaway
MR
ÚNICAMENTE en un lugar
con buena ventilación y no debe utilizarse en un edificio o garaje.
Este Tank Hideaway
MR
es diseñado para el uso con una bombona de
No úselo en la proximidad de objetos o de materiales
inflamables o combustibles.
se permite únicamente si la bombona estáSe desconectada y
No. de artículo: 67635
! LEER ANTES DEL USO Y CONSERVE PARA FUTURAS CONSULTAS
Tank Hideaway
MR
: Instrucciones de mantenimiento y uso
Este Tank Hideaway
MR
debe usarse únicamente en exteriores. Coloque siempre este Tank Hideaway
MR
sobre una superficie dura,
3

Paso 5: Junte el panel D a los paneles A y B Paso 6: Junte el panel E al panel B
utilizando 5 tornillos M5X10. utilizando 2 tornillos M6X30.
Paso 7: Cololque una bombona de Paso 8: Gire el tornillo mariposa (M8X30) al exterior
gas propano líquido (GPL) de 9 kg (20 lb) del soporte de metal en el sentido de las agujas del reloj
(no proporcionada) en el soporte de metal. para bien fijar la bombona de gas.
Asegúrese de que la bombona de gas quede
firmemente en el soporte de metal.
Paso 9: Coloque el regulador al interior del Paso 10: Conecte el regulador a la bombona de gas.
Tank Hideaway
MR
, y la manguera a través del
agujero al fondo del Tank Hideaway
MR
.
Patente pendiente
NO DEJE DE MANDARNOS UN CORREO ELECTRÓNICO AL
customer.service@bondmfg.com
O VISITE NUESTRA PÁGINA WEB BAJO ATENCIÓN AL CLIENTE
www.bondmfg.com
BOND MANUFACTURING CO.
1700 West 4th Street Antioch, CA 94509 USA
la válvula de la bombona. Asegúrese de que la manguera no esté oprimida debajo del Tank Hideaway
MR
.
SI TIENE PREGUNTAS O DUDAS
SE RUEGA LLAMAR A BOND SIN CARGOS al
1-866-771-BOND(2663) O PARA ACELERAR SU PEDIDO
**ADVERTENCIA**
Abra la tapa del Tank Hideaway
MR
para conectar o desconectar el regulador y para abrir y cerrar
4
Table of contents
Languages: