BONKOTE DMSD-140-10 User manual

DMSD Digital Mini solder Pot User’s Guide
Thank you for purchasing DMSD series soldering irons. Please read this guide before use, and keep it after read.
CAUTION
Do NOT touch the soldering irons with wet hands to prevent electrical accidents such as an electrical shock. .
Do NOT touch the iron tip and the heater anyti e when the power is on. Keep the away fro fla able aterials.
Keep the soldering iron unplugged after the operation.
Do NOT take a part or odify the soldering iron except for replace ent or aintenance.
Otherwise, it ay cause a fire, a failure or an electric shock.
 When the replace ent of the parts is needed, unplug the soldering iron and ake sure it cooled down.
 For the replace ent of the parts, use the genuine parts only. Otherwise, it ay cause a failure or an accident.
 Do NOT use the soldering iron for anything other than the regular soldering operation.
SPECIFICATIONS
◆
◆◆
◆ 2 PIN PLUG ( T PE A or C ) ※
※※
※ Weight and Length exclude a power cord.
Model No.
Power
consu ption
Input
voltage
Insulation
resistance
Standard ini
pot Weight
Di ensions
W * L* H
Control
Method
Te p.
range
I.D.
Mini pot
DMSD-140-10 40W
100VAC
20MΩ ≦
SG10-DP10 465g 80 * 285 * 60
0 volt
Switch
P- control
50~500℃
φ10 x 10D
DMSD-165-15 65W SGP10-DP15
490g 80 * 285 * 60 φ15 x 10D
DMSD-1100-30 100W SG12-DP30 620g 80 * 285 * 67 φ30 x 18D
DMSD-240-10 40W 220VAC SG10-DP10 465g 80 * 285 * 60 φ10 x 10D
DMSD-2100-30 100W SG12-DP30 620g 80 * 285 * 67 φ30 x 18D
◆
◆◆
◆ 3 PIN PLUG ( T PE B or I ) ※
※※
※ Weight and Length exclude a power cord.
Model No.
Power
consu ption
Input
voltage
Leak
voltage
Earth line
resistance
Standard ini
pot Weight
Di ensions
W * L* H
Control
Method Te p. range
I.D.
Mini pot
DMSD-140-10 40W
100VAC
≦ 2.0 V
(default)
≦ 2.0Ω
(default)
SG10-DP10 465g 80 * 285 * 60
0 volt
Switch
P- control
50~500℃
φ10 x 10D
DMSD-165-15 65W SGP10-DP15 490g 80 * 285 * 60 φ15 x 10D
DMSD-1100-30 100W SG12-DP30 620g 80 * 285 * 67 φ30 x 18D
DMSD-240-10 40W 220VAC SG10-DP10 465g 80 * 285 * 60 φ10 x 10D
DMSD-2100-30 100W SG12-DP30 620g 80 * 285 * 67 φ30 x 18D

Type B 100V
Type I 220V
STRUCTURE
※
※※
※ Power Plug
REPLACEMENT PARTS
Model No. Power
consu ption
Input voltage
Heater ele ent
Sol
d
er pot
Mini pot/heater-
cover/cover nut
Heater
collar Radiator nut Earth spring
DMSD-140-10 2 pin plug
40W
100VAC
CES-100-40E SG10-DP10 SUC-10 NA-11D
-
DMSD-165-15 2 pin plug
65W CES-100-65E SGP10-DP15 SUCP-10 NA-20D
DMSD-1100-30 2 pin plug
100W CES-100-100E
SG12-DP30 SUC-12 NA-30D
DMSD-240-10 2 pin plug
40W 220VAC CES-220-40E SG10-DP10 SUC-10 NA-11D
DMSD-2100-30 2 pin plug
100W CES-220-100E
SG12-DP30 SUC-12 NA-30D
DMSD-140-10 3 pin plug
40W
100VAC
CES-100-40E SG10-DP10 SUC-10 NA-11D
ECS-5
DMSD-165-15 3 pin plug
65W CES-100-65E SGP10-DP15 SUCP-10 NA-20D
DMSD-1100-30 3 pin plug
100W CES-100-100E
SG12-DP30 SUC-12 NA-30D
DMSD-240-10 3 pin plug
40W 220VAC CES-220-40E SG10-DP10 SUC-10 NA-11D
DMSD-2100-30 3 pin plug
100W CES-220-100E
SG12-DP30 SUC-12 NA-30D
※ Co on parts
Grip cover ・・・・・・ GC-R
Grip ・・・・・・・・・・・・ GK-DS
Pushbutton label ・・・ DMSDTR
Acrylic plate ・・・・・・ DS-AK
CONTROL PANEL
A Te perature control dial
B Power button
C Te perature UP button
D Te perature DOWN button
E Digital display
F LED la p
Flashing: rapid rise in te perature
ON: rise in te perature / suitable working te perature after saturation ti e
OFF: drop in te perature / stand-by / power off
Grip
cover
Minipot Heater
cover
Heater
collar
Earth
spring
Radiator
nut Heater
Cover
nut
Pushbutton
label
Acrylicplate
A B C D E F
Grip
Type A 100V
Type C 220V
Powerplug

HOW TO USE
1. Confir the voltage of the soldering iron and the power source is the sa e. Insert the power plug into the outlet.
「- - -」 is indicated on the display and the power is being delivered to the iron. The soldering iron beco es Stand-by ode.
2. Press and hold button ore than 3 seconds.
Default te perature is indicated on the display, and the power has been delivered to the heater in the iron.
Once is indicated on the display, release button.
3. When LED la p change to fro , you can start working.
When you start working, observe the solder in a pot has elted co pletely, the te perature rises higher and beco es stable
We reco end that you start working after confir ing the te perature is in stable. You could refer to the ti e in below chart.
※ Solder te perature reaches 90% of the set te perature.
4. After work, press and hold button ore than 3 seconds until 「- - -」 is indicated on the display,
and then the LED la p changes to . Check the display and release the button.
The latest set te perature should be applied whenever restarting the iron.
HOW TO CHANGE SET TEMP.
You can change the preset te perature by a long push or a short push of or buttons.
The short push changes the te perature by a single degree, and the long push changes it by 10 degrees at a ti e.
In case of the continuous soldering work for wires with large te perature capacity, the higher preset te perature is required.
TEMP. CONTROL DIAL
Using dial, you can allow to correct the te perature discrepancy between the set te perature and the elted solder in a pot.
Be sure not to over-twist dial.
※ The rotation angle fro the initial position is 120 degrees axi u to left and right
※ Use a precision Philips screwdriver
※ Clockwise: Rise the tip te perature
※ Counterclockwise: Drop the tip te perature
MEASURING THE MELTED SOLDER
. When easuring the elted solder te perature by using a ther o eter, do it after the ti e at the colu n C in the above chart,
so that you can obtain ore precise value.
LOCK FUNCTION
Press and hold buttons si ultaneously ore than 3 seconds to lock or unlock the set te perature.
Set te perature 300℃ 350℃
A B C A B C
Solder has
elted
Solder
te p.
beco e stable ※
※※
※
Solder te p.
arrive at set te p.
Solder has
elted
Solder
te p.
beco e stable ※
※※
※
Solder te p.
arrive at set te p
DMSD-140 (240) -10 5 in 8 in 12 in 3 in 5 in 30s 9 in 30s
DMSD-165-15 8 in 11 in 20 in 4 in 9 in 30s 15 in
DMSD-1100 (2100) -30 15 in 20 in 35 in 8 in 14 in 25 in
Te perature control dial
UP DOWN

HOW TO REPLACE IRON TIP AND HEATER
※ Before the replace ent, unplug fro the outlet and wait until the solder pot cools down.
IRON TIP
1. Loosen the cover nut to re ove the solder pot.
2. Replace the solder pot and tighten the cover nut.
HEATER
1. Disasse ble cover nut of solder pot and radiator nut.
2. Pull out the heater (both of heater ter inals and te perature sensor ter inals together) fro the connector.
※
※※
※ Make sure the connector must NOT come out from the grip when pulling heater out.
3. Replace the heater as follows:
Insert the te perature sensor ter inals and the heater
ter inals into the pin outlets as shown right.
※
※※
※ Be sure to align the red colored sensor terminals
with the red marked pin outlets.
4. Asse ble the parts in reverse order.
TROUBLE SHOOTING
Symptom Check Probable cause Measure
No electricity 「‐‐-」* is NOT shown on the
display.
Power cord disconnection or defect of circuit
board. Repairing
Soldering iron does NOT heat 「Eｒ1」* is shown on the display. Te perature sensor is OPEN. Replacing a heater
「Er3」* is shown on the display. Heater is OPEN.
T
e perature does NOT reach the
set te perature.
I p
le ent of te perature
co pensation.
Te perature co pensation has not
i ple ented.
I ple ent te perature
co pensation
After replace ent of a heater, the
soldering iron does NOT heat 「Eｒ2」* is shown on the display. Opposite polarity of te perature sensor ter inal. Correct the polarity.
Set te perature cannot be
adjusted. 「350」* is shown on the display. Set te perature ust be locked.
Release the lock
function.
* 「- - -」 Power is delivering. * 「Er1」「Er2」「Ｅｒ3」 Error * 「350」 Set te perature
GUARANTEE
Our products are shipped after severe factory test and inspection.
However, if you find alfunctions or defects due to proble s in work anship or transportation, please contact your dealer or us.
The guarantee period of your products is in one year after your purchase, except for replace ent parts.
AFTER SALES SERVICE
When your syste does not operate properly, read this anual again to check.
If still troubles are not solved, please contact your dealer or us.
■JAPAN BONKOTE CO.,LTD.
600-14 Kasahara-cho, Mito-shi,
Ibaraki 310-0852 JAPAN
Tel: [phone] Fax: [phone]
URL http://bonkote.co.jp
E- ail [e-mail]
Te p. Sensor ter inal
Te p. Sensing part Heater ter inal Pin outlet
Heater
Grip
cover
Minipot Heater
cover
Heater
collar
Earth
spring
Radiator
nut Heater Grip
Cover
nut
Pushbutton
label
Acrylicplate