Bosch Multicom BMC-3G User manual

Multicom BMC-3G GPRS Module
with Solution 2000 & 3000
There are 14 steps in this Multicom BMC-3G
Installation Guide. Please ensure you complete
each step in order.
The Multicom BMC-3G module is designed to provide GPRS Base Station reporting.
It connects directly to the panel on the SDI-2 Bus.
There are 14 steps that an Installer will need to follow to set up the panel and the GPRS unit.
The following is from the Multicom BMC-3G Installation Guide.
An overview of the basic hardware installation
steps. The full Multicom manual is available
---> bitly/mc3gman
1Mount the Panel
The BMC-3G fits into any standard alarm
panel housing.
Mounting or
placement inside the
existing alarm panel
housing requires the
provided fly lead to
be attached and the
included antenna to
be mounted to the
top of the panel.
Note: If the BMC-3G is being installed in a poor
signal area, please consider using a high-gain
antenna available from your Multicom supplier.
BMC-3G
(Steps 1-3)
AlarmLINK
(Steps 4-6)
TechTools
(Steps 7-14)
!
Connect
the BMC-3G
communicator to
your Bosch alarm
panel.
Setup arm/disarm
to give customers
control of the
Multicom via the
AlarmLINK app.
Install TechTools
and program the
Multicom. Add
relays and techs.
Use TechTools to
add customers to
AlarmLINK and
your logo.
2Connect to the Bosch Panel
The BMC-3G connects directly to the Bosch
panel as shown in the following wiring diagram.
If the 12V auxiliary power output is unable to
supply the required 200mA, connect to a fixed
12V DC power supply (>200mA).
Note that TOTAL CURRENT DRAW on the
SDI-2 bus is 900mA MAX including
Codepads and existing SDI-2 modules.
Introduction Connect the Multicom BMC-3G

A) When the Multicom BMC-3G is first connected to
the Bosch Alarm panel bus and powered up, it will
attempt to program the settings required for correct
alarm communications (RSC password / Installer
code must match). This is done automatically using
the same method as a direct connection (DLA USB
Serial) and A Link.
3Auto programming/Configuration (Solution 3000)
B) If auto programming fails due to
mismatch RSC password/installer code.
Then you can re-initiate auto-programming
by removing the Add jumper, wait 5
seconds, then replace.
For correct operation of the entire
system the RSC password (722) and
Installer Code (21) must be programmed
via TechTools to allow the Multicom
access to the 3000-series SDI-2 Bus.
4Download Installation Guide for Steps 4-14
If you go to the Suretek website:
https://mailchi.mp/suretek/multicom_bmc3g_press-release
You can download the Installation Guide and a Product Brochure.
An installer would need:
▶Suretek AlarmLINK APP: allows Arm/Disarm control by customers.
▶Suretek TechTools APP: used to program the Multicom unit.
Multicom Customer Service: 1300 654 433 ([phone])
Email: [e-mail]
Web: www.suretek.com.au
Suretek website
(Shortcut)
Scan the QR Codes below to download Setup Guides and Apps
AlarmLINK Setup Guide
Setup the end user app for your
customer.
bit.ly/alinkguide
AlarmLINK App Download
Available for iPhone and Android.
bit.ly/alinkapp
TechTools Download
Download the TechTools App for
smart phones.
bit.ly/multicom
Multicom Full Manual
A complete instructional guide.
bit.ly/mc3gman
!