Teknim TXM-0502 Instruction Manual

TXM-0502 GSM MODULE INSTALLATION AND USER MANUAL
1
Release Date: 12.02.2020
Rev:0
GENERAL:
Read this manual carefully before operating the devices and save them for later use. Follow all warnings and precautions
mentioned in the user manual. Follow all operating instructions, respectively.
✓Keep the devices away from water and moisture.
✓Since the device is not mounted securely, it may be harmful to the device and / or environment, so be sure to install the
device on a solid surface.
✓Always use the device with its own box.
ENVIRONMENTAL:
Do not operate the device in extreme hot and cold environments except the following conditions.
Temperature : Between -20C ~ +55C
Humidity : 0… %90rH
The radio transceiver module in the TXM-0502 Universal GSM device operates at GSM 850/900/1800/1900 MHz frequency
widths.
VENTILATION:
This device does not need ventilation.
POWER:
Use the device only with the voltage values specified in this manual. If you are unsure about the supply voltage of the device,
please contact your dealer or the manufacturer.
EARTHING AND POLARIZATION:
Before energizing the device, make sure that the grounding is properly connected. Note that the supply voltage is appropriate.
POWER CABLE PROTECTION:
Protect the power cord from being crushed and broken.
POWER LINE:
Especially for external applications, feed with a separate line from the power line of devices such as lighting lamps or power
circuit and keep away from the line of other devices.
It is recommended to supply External instead of AUX output on the alarm panel.
OVERLOAD:
To protect against the risk of electric shock or fire, do not connect extension cords and outlets to the device (s) that will draw
more current than usual.
OBJECT AND LIQUID INPUT:
To prevent fire and electric shock, make sure that no liquid or any object can enter the device, which may cause a short circuit.
SERVCE:
In case of any malfunction, contact your dealer or authorized service. Technical intervention to the device must be done by
qualified service personnel.
Do not try to repair the device yourself, if you open the cover of the device, you may be exposed to electric shock.
MALFUNCTIONS REQUIRING SERVICE:
In case of any malfunction or in the following cases, contact your authorized service or dealer.
✓When the power cord or plug is damaged
✓Any contact of water, rain or chemical liquid inside the device
✓When an object falls on the device or is hit
✓If the device has been dropped or the casing has been damaged
✓If the device has a noticeable level of performance change
✓Call the service if the device does not operate normally according to the operating instructions specified in the user manual
or because incorrect operations may cause other malfunctions.
TXM-0502 UNIVERSAL GSM MODULE
INSTALLATION & USER MANUAL

TXM-0502 GSM MODULE INSTALLATION AND USER MANUAL
2
SPARE PART:
If the repair is to be done by replacing the parts, make sure that the service technician is using original or equivalent parts against
the risk of fire, electric shock or another malfunction.
SECURITY CHECK:
Request service from your dealer to check whether the device operates in healthy, smooth, and safe conditions.
TRANSPORT AND SHIPPING:
The device should be handled with care so as not to experience any impact from outside and prevent fluid ingress. Malfunctions
occurring during improper transport are out of warranty.
HUMAN AND ENVIRONMENTAL HEALTH:
This device does not contain any chemical or biological substances that could harm human health.
WHAT YOU CAN DO WITH YOURSELF:
Do not try to repair the device yourself, because if you open the cover of the device, you may be exposed to electric shock. In case
of any malfunction, contact your dealer or authorized service. Technical intervention to the device must be carried out by qualified
service personnel. The device should be cleaned with a dry cloth. No chemicals should be used.
1. General
The task of the GSM Communicator Device is to enable the Alarm panel to reach the alarm centers or users by using the GSM
infrastructure in areas where there is no telephone line.
With the PSTN land line to be connected to the device, the Alarm panel will perform the necessary calls normally, and when the
telephone line is disconnected, it will be able to reach the alarm center or the user without interruption with the GSM
infrastructure.
The priority in communication is set as PSTN, and as long as the PSTN line is available, the land line will be used for calls. In case
the PSTN line is interrupted, it will be able to continue its communication over GSM.
Note: Alarm Panel cannot be reached via GSM while PSTN line is active.
2. General Structure of the Board

TXM-0502 GSM MODULE INSTALLATION AND USER MANUAL
3
Name
Explanation
Antenna
Antenna input used to receive GSM signals. Mount the antenna here
SIM Card Holder
Mechanism with inserted SIM card
System LED
Lights red if the GSM Module is operating normally
Signal LED
Lights green according to the signal status
Data LED
Lights blue during data processing
Connections
Name
Explanation
+12 V
+ Supply Voltage
GND
GND Supply Voltage
Earth
Ground Connection
Line (Tel)
Land Line Input
PTIP-PRING
Return connection for Land Line
Status LED Descriptions
System LED
RED
1x Flash per Second
System getting ready
Fixed Light
System Ready
Signal LED
Green
Not Active
No Signal
1x Flash in 3 Second
Signal Level is Medium
Multiple Flash in 1 Second
Signal is Good
Fixed Light
Signal is Very Good
Data LED
Blue
1x Flash per Second
Incoming or Outgoing Message
Fixed Light
Call is ongoing.
Technical Specifications
Power
10-24 VDC 300mA
Max Consumption
500mA
Average Consumption
120mA
GSM Frequency
850 / 900 / 1800 / 1900 Mhz
Call Tone Frequency
380 Hz
Operating Temperature
-20…+55C
Humidity
0-%90
3. Installation
✓The case is mounted on the wall with four holes, the screws and dowels are in the box.
✓There are cable entries suitable for flush or surface mounting, cables are brought into the case.

TXM-0502 GSM MODULE INSTALLATION AND USER MANUAL
4
MANUFACTURER
Bilgi Elektronik Sanayi ve Ticaret A.Ş.
Dudullu Organize Sanayi Bölgesi 1. Cadde İsmet Tarman İş
Merkezi No: 1 Kat: 2 No: 32 Ümraniye / İstanbul
Phone:
[phone] Fax: [phone]
www.bilgielektronik.com.tr www.teknim.com
[e-mail] [email protected]