Bosch UB-10DB Installation and operation manual

Surface Mount Dual 10” Subwoofer Accessories
en | Installation note
Original parts for:

Surface Mount Dual 10” Subwoofer Accessories Table of contents | en 3
Bosch Security Systems B.V. | Electro-Voice Installation note 2018.07 | 02 | F.01U.347.595
Table of contents
1Safety 4
1.1 Suspensions 4
1.2 Notices 4
2Short information 5
3Introduction 6
4Installation 7
4.1 Installing the U-bracket 7
4.2 Installing the transfomer input panel 8
4.3 Installing the crossover input panel 9
5Technical data 10
5.1 Dimensions 10

4en | Safety Surface Mount Dual 10” Subwoofer Accessories
2018.07 | 02 | F.01U.347.595 Installation note Bosch Security Systems B.V. | Electro-Voice
1 Safety
1.1 Suspensions
!
Warning!
Suspending any object is potentially dangerous and should only be attempted by individuals
who have a thorough knowledge of the techniques and regulations of suspending objects
overhead. Electro-Voice strongly recommends all loudspeakers be suspended taking into
account all current national, federal, state, and local laws and regulations. It is the
responsibility of the installer to ensure all loudspeakers are safely installed in accordance
with all such requirements. When loudspeakers are suspended, Electro-Voice strongly
recommends the system be inspected at least once per year or as laws and regulations
require. If any sign of weakness or damage is detected, remedial action should be taken
immediately. The user is responsible for making sure the wall, ceiling, or structure is capable
of supporting all objects suspended overhead. Any hardware used to suspend a loudspeaker
not associated with Electro-Voice is the responsibility of others.
!
Caution!
It is the installer's responsibility to determine and use the proper mounting hardware for
the wall construction type.
Disregarding this caution could result in damage to the product and personal injuries may
occur.
1.2 Notices
Copyright and disclaimer
All rights reserved. No part of this document may be reproduced or transmitted in any form by
any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of the publisher. For information on getting permission for reprints and
excerpts, contact Bosch Security Systems, Inc.
The content and illustrations are subject to change without prior notice.

Surface Mount Dual 10” Subwoofer Accessories Short information | en 5
Bosch Security Systems B.V. | Electro-Voice Installation note 2018.07 | 02 | F.01U.347.595
2 Short information
The following table lists products in a family, with CTN (Commercial Type Number) and
identifying product name DESCRIPTION.
CTN Description
UB-10DB U-bracket for 10" subwoofer black
UB-10DW U-bracket for 10" subwoofer white
IP-10D-TB Transformer input 10" subwoofer bk
IP-10D-TW Transformer input 10" subwoofer wh
IP-10D-CB Crossover input 10" subwoofer bk
IP-10D-CW Crossover input 10" subwoofer wh

6en | Introduction Surface Mount Dual 10” Subwoofer Accessories
2018.07 | 02 | F.01U.347.595 Installation note Bosch Security Systems B.V. | Electro-Voice
3 Introduction
This installation note describes how to install the wall mount bracket, transformer input panel,
and crossover input panel used with the EVID-S and LB20 dual 10" subwoofers. The
accessories are available in black or white.
These products are compatible with the following products:
CTN Description
EVID-S10.1DB Cabinet subwoofer 2x10" black
EVID-S10.1DW Cabinet subwoofer 2x10" white
LB20-SW400-D Cabinet subwoofer 2x10" black
LB20-SW400-L Cabinet subwoofer 2x10" white
Read through this manual to familiarize yourself with the safety information and applications
before you use these products.

Surface Mount Dual 10” Subwoofer Accessories Installation | en 7
Bosch Security Systems B.V. | Electro-Voice Installation note 2018.07 | 02 | F.01U.347.595
4 Installation
For safety, ensure the mounting surface supports more than the weight of the speaker. Use
only industry-accepted fasteners and mounting methods when mounting the loudspeaker.
Consult an expert if you are unsure.
!
Caution!
It is the installer's responsibility to determine and use the proper mounting hardware for the
wall construction type.
Disregarding this caution could result in damage to the product and personal injuries may
occur.
Safety point
As an added safety measure, it is suggested the user install an extra suspension point back to
the building structural supports. This safety point should have as little slack as possible (less
than 1-inch is preferable).
4.1 Installing the U-bracket
To install the U-bracket, do the following:
1. Install the four screws (provided) into the U-bracket mounting points.
2. Install a 10-mm rated forged eyebolt (not included) into the safety point.
3. Secure the subwoofer from the safety eyebolt using a rated fittings and steel cable.
Suspending the subwoofer in a down-fire position using the U-bracket
To suspend the subwoofer in a horizontal down-fire position, do the following:
1. Install two 10-mm rated forged eyebolts using lock washers (eyebolts and lock washers
are not included) into the fly points on the U-bracket.
2. Install a 10-mm rated forged eyebolt (not included) into the safety point.
3. Suspend the subwoofer from the eyebolts using rated fittings and steel cable.
4. Secure the subwoofer from the safety eyebolt using a rated fittings and steel cable.

8en | Installation Surface Mount Dual 10” Subwoofer Accessories
2018.07 | 02 | F.01U.347.595 Installation note Bosch Security Systems B.V. | Electro-Voice
4.2 Installing the transfomer input panel
To install the transformer input panel, do the following:
1. Remove the standard input panel.
2. Disconnect the standard input panel.
3. Connect the transformer input panel.
4. Install the transformer input panel.
5. Install the weather cover, if applicable.

Surface Mount Dual 10” Subwoofer Accessories Installation | en 9
Bosch Security Systems B.V. | Electro-Voice Installation note 2018.07 | 02 | F.01U.347.595
4.3 Installing the crossover input panel
To install the crossover input panel, do the following:
1. Remove the standard input panel.
2. Disconnect the standard input panel.
3. Connect the crossover input panel.
4. Install the crossover input panel.
5. Install the weather cover, if applicable.

10 en | Technical data Surface Mount Dual 10” Subwoofer Accessories
2018.07 | 02 | F.01U.347.595 Installation note Bosch Security Systems B.V. | Electro-Voice
5 Technical data
Color: Black or white
Dimensions (H x W x D): 170 mm x 505 mm x 760 mm
(6.69 in x 19.88 in x 29.92in)
Net weight: 4.66 kg (10.24 lb)
Shipping weight: 5.46 kg (12.04 lb)
Tab.5.1: U bracket
Color: Black or white
Dimensions (H x W x D): 250 mm x 240 mm x 460 mm
(9.84 in x 9.45 in x 18.11 in)
Net weight: 5.03 kg (11.04 lb)
Shipping weight: 5.67 kg (12.50 lb)
Tab.5.2: Transformer input
Color: Black or white
Dimensions (H x W x D): 250 mm x 240 mm x 460 mm
(9.84 in x 9.45 in x 18.11 in)
Net weight: 1.71 kg (3.76 lb)
Shipping weight: 2.34 kg (5.16 lb)
Tab.5.3: Crossover input
5.1 Dimensions
The U-bracket dimensions are not to scale and are for reference only.

Surface Mount Dual 10” Subwoofer Accessories Technical data | en 11
Bosch Security Systems B.V. | Electro-Voice Installation note 2018.07 | 02 | F.01U.347.595
100.0 mm
[3.94 in]
8x 10.0 mm [8x 0.39 in]
8x 38.1 mm
[8x 1.50 in]
2x 21.0 mm
[2x 0.82 in]
2x 21.0 mm
[2x 0.82 in]
4x 22.5 mm [4x 0.87 in]
4x 22.5 mm
[4x 0.89 in] 3x 13.0 mm∅
[3x 0.51 in]∅
632.0 mm
[24.88 in]
220.0 mm
[8.66 in]
220.0 mm
[8.66 in]
2x 21.0 mm
[2x 0.82 in]
316.0 mm
[12.44 in]
2x 21.0 mm
[2x 0.82 in]
3x 50.0 mm
[3x 1.97 in]
Figure5.1: Dimensions - 10" U-bracket

Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
www.boschsecurity.com
© Bosch Sicherheitssysteme GmbH, 2018
Bosch Security Systems, Inc
12000 Portland Avenue South
Burnsville MN 55337
USA
www.electrovoice.com