Bosch Security Systems TC9217MM-W User manual

1 of 11 ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
Instruction Manual
EN Monitor Mounts
TC9217MM-W, TC9220MM-W, TC9227MM-W

2 of 11 ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
TC9217MM-W, TC9220MM-W, TC9227MM-W | Instruction Manual | EN
|
2
Bosch Security Systems | February 3, 2005
MONITOR MOUNT COMPATIBILITY CHART
For Bosch LTC Series Monitors
Bosch Monitor Ceiling Wall
Model No. Mount Mount
Monochrome
LTC 2009/51, /61 MM3000 TC9209MM-W
LTC 2012/51, /61 MM3000 TC9209MM-W
LTC 2017/50, /60 TC9217MM-C TC9217MM-W
LTC 2020/90 TC9220MM-C TC9220MM-W
Color
LTC 2810/90, /91 TC9217MM-C TC9217MM-W
LTC 2813/90 TC9217MM-C TC9217MM-W
LTC 2814/90 TC9217MM-C TC9217MM-W
LTC 2821/90, /91 TC9220MM-C TC9220MM-W
LTC 2910/90 MM3000 TC9209MM-W
LTC 2915/91 TC9217MM-C TC9217MM-W
LTC 2917/91 TC9217MM-C TC9217MM-W
LTC 2919/90 TC9220MM-C TC9220MM-W
27ST220L TC9227MM-C TC9227MM-W
Installation Hint for TC9217MM, TC9220MM, and TC9227MM Series Monitor Mounts, RE: Step 4.
For proper center of gravity alignment of Bosch monitors on the bottom support tray, a recommended starting point is to
use the third (3rd) square hole from the front edge of the tray to mount the vertical support arm using pin E.
SERVICE
If the unit needs servicing, contact the nearest Bosch Security Systems Service Center for authorization to return
and shipping instructions.
Service Centers
USA
Phone: [phone] or 717-735-6638
Fax: [phone] or 717-735-6639
CCTV Spare Parts
Phone: [phone] or 408-956-3853 or 3854
Fax: [phone]
E-mail: [email protected].com
Canada
Phone: [phone]
Europe, Middle East & Asia Pacific Region
Phone: [phone]
For additional information, see www.boschsecurity.com.

3 of 12ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
Installation and Assembly
BOSCH Monitor Wall Mounts Models: TC9217MM-W, TC9220MM-W,
TC9227MM-W
Each monitor mount is for use with a single TV or monitor of a specified size only.
IMPORTANT! Read entire
instruction sheet before you
start installation and assembly.
IMPORTANT! If attaching a VCR Mount
carefully study both product instruction sheets
before assembly. The interface bracket
(included with the VCR Mount) must be
attached during monitor mount assembly to
avoid disassembly later.
Before you start make sure all parts
shown (see parts list, page 9) are
included with your bracket.
SIDEVIEW
TV
FLOOR
Place TV onto a piece of pipe as
shown.(Pipeshouldbeafewinches
wider than the TV.) Roll TV back and
forth to find the balance point. This is
the center of gravity. Mark the center
of gravity on the side of the TV.
CENTEROF
GRAVITY
A
Adjust support tray (A, three
pieces) to match width of TV.
Locksupporttrayusingfour
carriagebolts(B),washer/
nutcombo(C).Tighten
securely.
B
C
Attachadhesive
pads (X) to top
clamps(Q).
Insert plastic
covers(CC)onto
endsofanti-rollout
hooks(R).
TV
Q
XR
CC
BOSCH
R
This product is intended for use with UL
Listed products and must be installed by a
qualified professional installer.
Model #:
TC9217MM-W
TC9220MM-W
TC9227MM-W 27"
Product is UL rated up to ___ TV
sizes, per attached chart
TV size
17"
21"

4 of 12ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
E
Z
P
R
Y
Y
R
P
Attach support tray (A)
toverticalsupportarms
(P) as shown.
Note:Choosethesquare
hole which aligns closest
withthecenterofgravity
mark on the TV (as
determinedin step 1).
Attachanti-rollout hooks
(R) as shown using M6
screws(Z)andretainer
bars(Y).Note:Extruded
sideofretainerbar(Y)
goestowardsanti-rollout
hook(R).
Hand tighten only.
A
Althoughtop clamps(Q)and anti-rollout
hooks (R) [see step 7] will provide more than
adequate support for the TV, some installers
may wish to also attach the support tray to
the TV bottom.
Using uni-clips (G) and M5 screws (F) (see
instruction card in fastener pack), or #10 x
3/4"particle boardscrews (H)andwashers
(I) (for attachment to mounting bosses if
present), or a combination of both, attach
support tray (A) to TV bottom. [To do this
place TV upside down on a flat stable
surfaceand positionsupport trayupside
down on TV bottom.] Attach at four places
as close to the four corners of the TV bottom
as possible.
O P T I O N A L
G
F
H
TVBOTTOM
A
TV
(UPSIDEDOWN)
Y
R
J
I

5 of 12ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
For Wood Stud Walls drill three 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm) into stud center.
Attach wall arm (W) using three #14 x 2.5" (6 mm x 65 mm) wood screws (V).
WOOD
STUD
WALL
W
V
• Tightenwoodscrews so wall arm is firmly attached,butdonot tighten with excessive force! Overtighteningcan
cause stress damage to wood screws, greatly reducing their holding power. Tighten to 80 in • lb (9 N.M.) maxi-
mumtorque.
WARNING

6 of 12ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
Drill hole(s) and insert anchor(s)
CUTAWAYVIEW
INCORRECT
concrete
plaster/
drywall
wall
arm
concrete
wall
1
3
2wall arm
CORRECT
concrete
plaster/
drywall
For Concrete Walls use wall arm (W), making sure
that it is level, as a template to mark holes. Drill 1/
4" (6 mm) dia. holes to a minimum depth of 2.5" (64
mm). Insert concrete anchors in holes flush with
wallasshown (right). Place wall arm (W) over
anchors and secure with #14 x 2.5" (6 mm x 65
mm)wood screws (V).Tighten allfasteners.
wall
arm
ACC 204
ACC 204
WARNING
• When installing BOSCH wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill
toavoidbreaking out the back of theholewhen entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hard-
wareand components.
CONCRETE
WALL
V
ACC 204
W
Place arm over anchor(s) and secure with screw(s)
Tighten all fasteners
• Tighten wood screws so that wall plate is firmly
attached,but do notovertighten. Overtightening can
damagethescrews, greatly reducing theirholding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the studs. The use of an "edge to edge" stud
finderis highly recommended.
WARNING
• Concrete anchorsare not intendedfor attachment to
concretewallcovered with a layer ofplaster, drywall,
orotherfinishing material. If mounting toconcretewall
coveredwith plaster/drywallisunavoidable, plaster/
drywall (up to 5/8" thick) must be counterbored as
shown below. If plaster/drywall is thicker than 5/8",
custom fasteners must be supplied by installer.
WARNING

7 of 12ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
Q
P
R
DETAIL 2
K
Position TV onto support tray (A).Positionanti-rollouthooks(R) against front edge of TV.
FIRST: From the top fully thread flush mount tube
(T) into threaded fitting in wall arm or ceiling plate.
Install the wall arm or ceiling plate according to
instructions included with it.
NEXT: Attach right and left tilt brackets (AA &BB)
to horizontal support (S) using four screws &
washercombo(J).Beforetighteningscrewsmake
sure tilt brackets are adjusted horizontally to align
precisely with screws in the side of vertical support
arms (P). Attach horizontal support (S) to wallarm
or ceiling plate using fiber washers (M &N), spacer
(U,only includedwithsmaller models) andretaining
collar(O).IMPORTANT:Retainingcollar(O)
requiresasafetyscrew[refertoDETAIL3,page8].
FINALLY: Be sure that hooks in right and left tilt
brackets(AA&BB)areopenendforward.Hangthe
TV / bracket assembly.
AA
BB
Wall arms & ceiling plates
include their own
instructions. Fixed length
and adjustable extension
columns are also available.
CMJ 470,
CMJ 480,
CMJ 490
WMJ 018,
WMJ 022
P
M
O
U
N
T
T
S
*
*
Included with models
TC9217MM and
TC9220MM only.
**
**
Note: Slots in corners of top clamps (Q) and corners of vertical support arms (P) allow for the installation of safety belt
(model ACC 666, sold separately). If using this belt, install it now.
WMJ 025H
J
WARNING
• Each anti-rollout hook (R) should have at least 1/4” of surface contact with the front of theTV. If this is not the
case the support tray (A) must be adjusted smaller [see step 2], or the vertical support arms (P) adjusted inward
[see step 4].
Inserttopclamps (Q). Note: Top clamps(Q)fit between rolloutprotectors(R)and vertical supportarms(P)
[DETAIL 1]. Press down on each top clamp (Q) while securely tightening each M6 screw (Z).
Byhand, threadone serratedflangeheadscrew(K)intoeach verticalsupport arm(P) intooneofthreethreaded
holes [1, 2, or 3; DETAIL 2]. Choose the threaded hole that will allow just enough tilt clearance [see step 9].
Leaveabout1/4"ofexposedthread.
• Donotliftmoreweightthanyoucanhandle!
Useadditional manpower ormechanicallifting
equipment to safely lift and hang the TV /
Bracketassembly!
WARNING
Insert one screw & washer combo (J) through slot
in each tilt bracket (AA & BB). Hand tighten.
P
R
R
Q
Q
A
Q
P
RZ
DETAIL 1

8 of 12ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
When attaching the horizontal support (S) to wall arm or
ceilingplate, carefullythread retainingcollar (O)ontoendof
flush mount (T) tube (or extension column). Tighten at least
fourcomplete turnsendingwith oneof thesmallthreaded
holes aligned with slot in the end of flush mount tube (T) (or
extension column). Insert and tighten one M5 screw (F).
T
S
FO
DETAIL 3
(BOTTOMVIEW)
S
TILTCLEARANCE
Adjust TV to desired tilt then tighten screws. Maximum tilt
is 30°. If tilt clearance is a problem revisit step 7, DETAIL 2.
• Set screw (F) is self tapping and may be hard to get
started but is essential to this installation. Failure to
install this screw can cause the mount to fall.
WARNING
• Tighten all screws securely.
WARNING

9 of 12ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
Q
Q
X
X
S
BB M
O
N
U
T
Note: Parts may appear slightly different than illustrated.
A1
A2
A3
P
P
R
R
Y
Y
AA
C
E
ZCC
F
H
V
K
JI
B
G
TC9217MM-W TC9220MM-W TC9227MM-W
Description Qty. Part # Part # Part #
A1 left end support tray 1 128-1023 128-1026 128-1026
A2 right end support tray 1 128-1024 128-1027 128-1027
A3 center support tray 1 128-1128 128-1134 128-1135
B5/16 - 18 x 1/2" carriage bolt 4 520-9207 520-9207 520-9207
C5/16-18 washer/nut combo 4 530-1016 530-1016 530-1016
EM10-1.5 x .7 flange nut 2 520-9261 520-9261 520-9261
FM5 x .8 x 10 mm screw 6 520-9250 520-9250 520-9250
Guni-clip 4 2245-081 2245-081 2245-081
H#10 x 3/4" particle board screw 4 500-9006 500-9006 500-9006
I#10 flat washer 4 540-9400 540-9400 540-9400
JM10 socket head lock/flat washer combo screw 8 520-1041 520-1041 520-1041
KM10 serrated flange head screw 2 520-1105 520-1105 520-1105
Mfiber washer - large inside dia. 1 540-9432 540-9432 540-9432
Nfiber washer - small inside dia. 1 540-9431 540-9431 540-9431
Oretaining collar 1 1800-375 1800-375 1800-375
Pvertical support arm 2 128-1107 128-1109 128-1111
Qtop clamp 2 128-1138 128-1138 128-1138
Ranti-rollout hook 2 128-1116 128-1116 128-1116
Shorizontal support 1 128-1016 128-1017 128-1018
Tflush mount tube 1 1446-014 1446-014 1446-014
Uspacer 1 128-0067 128-0067 -
V#14 x 2.5" (6 mm x 65 mm) screw 4 5S1-015-C03 5S1-015-C03 5S1-015-C03
Wsingle wall arm 1 128-1059 128-1059 128-1069
Xadhesive pads (not shown) 2 570-0024 570-0024 570-0024
Yretainer bar 2 128-1117 128-1117 128-1117
ZM6 x 18mm flat phillips screw 2 520-1166 520-1166 520-1166
AA tilt bracket right 1 128-1342 128-1337 128-1337
BB tilt bracket left 1 128-1341 128-1336 128-1336
CC plastic cover for anti-rollout hook 2 590-1055 590-1055 590-1055
Parts List
W

10 of 12 ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
(330 mm) (432 mm)
(482 mm) (533 mm)
(482 mm) (533 mm)
(635 mm) (686 mm)
(635 mm) (686 mm)
(635 mm) (686 mm)
(635 mm) (686 mm)
(762 mm) (889 mm)
(686 mm) (889 mm)
(940 mm) (1067 mm)
(889 mm) (1067 mm)
Mount
GENERAL WALLMOUNTKITSPECIFICATIONS
Model
Number
TV/Monitor ProductBOSCHrated
when attached to...
Support
Tray
Depth(D)
10"
10"
14"
10"
14"
14"
14"
14"
14"
14"
14"
Screen Size
13" - 17"
19" - 21"
19" - 21"
25" - 27"
25" - 28"
25" - 27"
wood
stud
125 lb
125 lb
125 lb
125 lb
125 lb
125 lb
300 lb
300 lb
300 lb
300 lb
300 lb
150 lb
150 lb
150 lb
150 lb
150 lb
150 lb
300 lb
300 lb
300 lb
300 lb
300 lb
concrete,
cinder block
or brick
(57 kg)
(57 kg)
(57 kg)
(57 kg)
(57 kg)
(65 kg)
(65 kg)
(65 kg)
(65 kg)
(65 kg)
(254 mm)
(254 mm)
(356 mm)
(254 mm)
(356 mm)
TC9217MM-W
TC9220MM-W
TC9227MM-W
Reach(R)
18" (457 mm) for models TC9217MM-W, TC9220MM-W.
22.5" (572 mm) for models TC9227MM-W.
• Weight of TV or monitor not to exceed Max. Load
Capacity(BOSCH rating)!
WARNING
R
Dsupport tray
300tilt
range
TV
wall