Bosch NDA-FMT-DOME User manual

In-ceiling mount
NDA-FMT-DOME
en Installation manual

Table of contents
1Safety 4
1.1 Safety message explanation 4
2Installation Overview 5
3Installing a Recessed Mount 6
3.1 Overview 6
3.2 Installing the Recessed Mount 6
3.3 Installing the Camera to the Recess Mount 10
4Technical data 11
In-ceiling mount Table of Contents | en 3
Bosch Security Systems 2014.08 | v1.0 | AM18-Q0679

Safety
Before installing, please read this manual carefully.
Safety message explanation
!
Caution!
Indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
Notice!
Indicates a situation which, if not avoided, could result in
damage to the equipment or environment, or data loss.
!
Caution!
Installation should only be performed by qualified service
personnel in accordance with the National Electrical Code
(NEC 800 CEC Section 60) or applicable local codes.
1
1.1
4en | Safety In-ceiling mount
2014.08 | v1.0 | AM18-Q0679 Bosch Security Systems

Installation Overview
This equipment should be unpacked and handled with care. If an
item appears to have been damaged in shipment, notify the
shipper immediately.
Verify that all parts are included. If any items are missing, notify
your Bosch Security Systems Sales or Customer Service
Representative.
The original packaging is the safest container in which to
transport the unit and can be used if returning the unit for
service.
The following parts are included:
Quantity Part
1 In-ceiling mount: NDA-FMT-DOME
1 White trim ring A (inner diameter: 102 mm) with
two M3 captive screws
1 White trim ring B (inner diameter: 98 mm) with
two M3 captive screws
4 Four M4 x 6 mm screws
4 Four M4 x 15 mm screws
1 Security Torx T-10 L wrench
1 Installation manual (this booklet)
2
In-ceiling mount Installation Overview | en 5
Bosch Security Systems 2014.08 | v1.0 | AM18-Q0679

Installing a Recessed Mount
Overview
The mount is supplied with two different trim rings and different
tooling hole positions on the sides of the recess mount. Use the
trim ring and hole position best suited for your camera.
Installing the Recessed Mount
Notice!
The recessed mounting bracket is provided with an additional
safety tether point. To prevent injury, attach a safety wire from
a secure anchor point above the ceiling to this tether point.
To mount to a recess mount, do the following:
1. Determine a secure location for the recessed mount.
96 (3.78)
194 (7.64)
55.1 (2.17)
Figure 3.1: Recess Mount Dimensions
2. Drill or cut a 7 in. hole with a tolerance of ±1/8 in. (177.8
±2.2 mm).
3
3.1
3.2
6en | Installing a Recessed Mount In-ceiling mount
2014.08 | v1.0 | AM18-Q0679 Bosch Security Systems

3. Optional: if installing the camera to a suspended ceiling tile
or any other surface where additional support is required,
the VGA-IC-SP mounting kit (sold separately) is
recommended. See the instruction book supplied with the
mounting bracket for installation instructions.
Figure 3.2: Mounting bracket
4. Ensure that the clamping plates are angled inward by
pushing up and into the two slots.
5. Insert mount through the hole and into the ceiling. Slide
clamps out and down so that the drywall is clamped in
between the clamps and the bracket flange, 41.7 mm (1.64
in.) maximum ceiling thickness and 9.7 mm (0.38 in.)
minimum ceiling thickness).
In-ceiling mount Installing a Recessed Mount | en 7
Bosch Security Systems 2014.08 | v1.0 | AM18-Q0679

Figure 3.3: Attach Recess Mount to Ceiling
Figure 3.4: Clamp Recess Mount
6. Tighten both clamps to the ceiling using supplied screws
and a #2 Phillips screwdriver.
8en | Installing a Recessed Mount In-ceiling mount
2014.08 | v1.0 | AM18-Q0679 Bosch Security Systems

Figure 3.5: Tighten Mounting Clamps
Notice!
Over tightening the ceiling clamps can damage the clamp or
ceiling. Only tighten the clamp until it contacts the ceiling and
you start to feel some resistance. If using a power screwdriver,
set the torque level to the lowest setting.
In-ceiling mount Installing a Recessed Mount | en 9
Bosch Security Systems 2014.08 | v1.0 | AM18-Q0679

Installing the Camera to the Recess Mount
To install the camera to the recess mount, follow these steps:
!
Caution!
All wires for installation applications must be routed through a
grounded conduit.
1. Route wires through the crescent shaped cut-out on the
side of mounting plate.
2. Connect the cables according to the instructions in the
installation guide.
3. Remove the outer housing from the camera (use the
wrench supplied with the camera).
4. Attach the camera base to the recessed mount using the
M4 x 15 mm mounting screws. Ensure that the cable is
aligned with the cutout in the recess mount.
5. Reattach the camera the outer housing.
6. Align the mounting screws of the trim ring with the
mounting holes in the recess mount.
7. Use the supplied T-10 Torx wrench to secure the trim ring’s
safety locking screws to the mounting bracket.
3.3
10 en | Installing a Recessed Mount In-ceiling mount
2014.08 | v1.0 | AM18-Q0679 Bosch Security Systems

Technical data
37.38
119.42
17.19
99.22
A
AA
A
B
B
C C
C
C
Ø129.70
Ø104
4
In-ceiling mount Technical data | en 11
Bosch Security Systems 2014.08 | v1.0 | AM18-Q0679

Bosch Security Systems B.V.
Torenallee 49
5617 BA Eindhoven
The Netherlands
www.boschsecurity.com
© Bosch Security Systems B.V., 2014