Bosch NDP-5512-Z30C User manual

AUTODOME IP starlight 5000i
NDP‑5512‑Z30 │ NDP‑5512‑Z30C
en User Manual

AUTODOME IP starlight 5000i Table of contents | en 3
Bosch Security Systems User Manual 2019-11 | 1.2 |
Table of contents
1Introduction 6
1.1 Systems requirements 6
1.2 Establishing the connection 6
1.3 Password protection in camera 7
2System overview 8
2.1 Live page 8
2.2 Configuration 8
2.3 Playback 8
2.4 Dashboard 9
3Operation via the browser 10
3.1 Live page 10
3.1.1 Connection 10
3.1.2 PTZ 10
3.1.3 Pre-positions 10
3.1.4 AUX Control 11
3.1.5 Digital I/O 11
3.1.6 Special Functions 11
3.1.7 Recording status 12
3.1.8 Saving snapshots 12
3.1.9 Recording live video 12
3.1.10 Full-screen display 12
3.1.11 Audio communication 12
3.1.12 Storage, CPU and network status 12
3.1.13 Status icons 13
3.2 Playback via browser 13
3.2.1 Selecting the recording stream 14
3.2.2 Searching for recorded video 14
3.2.3 Exporting recorded video 14
3.2.4 Controlling playback 14
4General 15
4.1 Identification 15
4.2 User Management 15
4.3 Date/Time 16
4.4 Display Stamping 17
4.5 GB/T 28181 19
5Web Interface 21
5.1 Appearance 21
5.2 LIVE Functions 22
6Camera 23
6.1 Installer Menu 23
6.2 Scene Mode 23
6.2.1 Picture Settings 24
6.2.2 Enhance 25
6.2.3 Scene Mode Scheduler 26
6.3 Color 26
6.4 ALC 28
6.5 Enhance 29
6.6 Scene Mode Scheduler 29

4en | Table of contents AUTODOME IP starlight 5000i
2019-11 | 1.2 | User Manual Bosch Security Systems
6.7 Encoder Profile 29
6.8 Encoder Streams 32
6.9 Encoder Regions 32
6.10 Encoder Statistics 33
6.11 Privacy Masks 33
6.12 Picture Settings 34
6.13 Lens Settings 36
6.14 PTZ Settings 36
6.15 Pre-positions and Tours 37
6.16 Pre-position mapping 38
6.17 Sectors 39
6.18 Miscellaneous 39
6.19 Audio 39
6.20 Pixel Counter 40
7Recording 41
7.1 Introduction to recording 41
7.2 Storage Management 41
7.2.1 Device manager 41
7.2.2 Recording media 41
7.2.3 Activating and configuring storage media 42
7.2.4 Formatting storage media 42
7.2.5 Deactivating storage media 42
7.3 Recording Profiles 42
7.4 Maximum Retention Time 44
7.5 Recording Scheduler 44
7.6 Recording Status 45
7.7 Recording Statistics 45
7.8 Image Posting 45
7.9 SD Card Status 46
8Alarm 47
8.1 Alarm Connections 47
8.2 Video Content Analysis (VCA) 49
8.3 Audio Alarm 51
8.4 Alarm E-Mail 51
8.5 Alarm Task Editor 52
8.6 Alarm Rules 53
9Network 54
9.1 Network Services 54
9.2 Network Access 54
9.3 DynDNS 56
9.4 Advanced 57
9.5 Network Management 58
9.6 Multicast 59
9.7 Image Posting 60
9.8 Accounts 61
9.9 IPv4 Filter 61
9.10 Encryption 61
10 Service 62
10.1 Maintenance 62

AUTODOME IP starlight 5000i Table of contents | en 5
Bosch Security Systems User Manual 2019-11 | 1.2 |
10.2 Licenses 62
10.3 Certificates 63
10.4 Logging 63
10.5 Diagnostics 63
10.6 System Overview 63
11 AUX Commands 64
12 Troubleshooting 65
12.1 Rebooting the unit 66
12.2 Physical reset button 67
12.3 Customer Service and Support 68

6en | Introduction AUTODOME IP starlight 5000i
2019-11 | 1.2 | User Manual Bosch Security Systems
1 Introduction
1.1 Systems requirements
– Computer with Intel Skylake processor or better
– Intel HD530 graphic card with performance that matches or is better than the resolution
of the camera
– Windows7 (or newer) operating system
– Network access
– Web browser:
– Internet Explorer version 11 (or newer)
Mozilla Firefox
– Application software, for example, VideoSecurityClient, BoschVideoClient, BVMS, or
Project Assistant app.
– DirectX 11
– MPEG-ActiveX 6.33 (or newer) [required to see, in your browser, live images from the
camera]
– Configuration Manager 6.20 (or newer)
1.2 Establishing the connection
The unit must have a valid IP address to operate on your network and a compatible subnet
mask.
By default, DHCP is pre-set at the factory to On plus Link-Local so a DHCP server assigns an
IP address or, if no DHCP server is available, a link-local address (auto-IP) is assigned within
the range 169.254.1.0 to 169.254.254.255.
You can use IP Helper or Configuration Manager to find the IP address. Download the software
from http://downloadstore.boschsecurity.com.
1. Start the Web browser.
2. Enter the IP address of the unit as the URL.
3. During initial installation, confirm any security questions that appear.
If a RADIUS server is used for network access control (802.1x authentication), you must
configure the device before the device can communicate with the network.
To configure the device, connect it directly to a computer using a network cable and then set
the service-level password.
Note:
If you cannot connect, the unit may have reached its maximum number of connections.
Depending on the device and network configuration, each unit can have up to 50 web browser
connections, or up to 100 connections via BoschVideoClient or Bosch Video Management
System.

AUTODOME IP starlight 5000i Introduction | en 7
Bosch Security Systems User Manual 2019-11 | 1.2 |
1.3 Password protection in camera
The device is password-protected. The first time that any user accesses the device, the device
will prompt the user to set a password at the service level.
The camera requires a strong password. Follow the prompts in the dialog box, which specifies
what is required. The system measures the strength of the password that you enter.
When you use Configuration Manager to access your device for the first time, you must set the
initial password of the device in Configuration Manager. The Users section (General > Unit
Access > Users) displays the message, "Before you can use this device you have to secure it
with an initial password."
Note: After you set the initial password, a "lock" icon appears next to the device name in the
Devices list in Configuration Manager.
You can also launch the device webpage directly. In the device webpage, an initial password
page appears, displaying input fields and a password strength gauge.
Enter the user name (“service”) and a password in the appropriate fields. Refer to the section
User Management for more information.
After a service-level password is set for the device, the device displays a dialog box that
prompts users to enter the user name (“service”) and the service-level password every time
that they access the device.
1. Fill in the fields User name and Password.
2. Click OK. If the password is correct, the desired page appears.

8en | System overview AUTODOME IP starlight 5000i
2019-11 | 1.2 | User Manual Bosch Security Systems
2 System overview
When a connection is established, the Live page is initially displayed.
The application bar displays the following icons:
Live Click this icon to view the live video stream.
Playback Click this icon to play back recorded sequences.
This link is only visible if a storage medium has been
configured for recording. (With VRM recording, this
option is not active.)
Configuration Click this icon to configure the device.
Dashboard Click this icon to see detailed system information.
Links Click this icon to navigate to the Bosch download store.
Click this icon to get context-sensitive help for the page
you are browsing.
2.1 Live page
The Live page is used to display the live video stream and control the unit.
2.2 Configuration
The Configuration page is used to configure the unit and the application interface.
Making Changes
Each configuration screen shows the current settings. You can change the settings by entering
new values or by selecting a predefined value from a list field.
Not every page has a Set button. Changes to pages without a Set button are set immediately.
If a page does show a Set button, you must click the Set button for a change to take effect.
Notice!
Save each change with the associated Set button.
Clicking the Set button saves the settings only in the current field. Changes in any other fields
are ignored.
Some changes only take effect after the unit is rebooted. In this case, the Set button changes
to Set and Reboot.
1. Make the desired changes.
2. Click the Set and Reboot button. The camera reboots and the changed settings are
activated.
All settings are backed up in camera memory so they are not lost even if the power fails. The
exception is the time settings, which are lost after 1 hour without power if no central time
server is selected.
2.3 Playback
The Playback page is used for playing back recorded sequences.

AUTODOME IP starlight 5000i System overview | en 9
Bosch Security Systems User Manual 2019-11 | 1.2 |
2.4 Dashboard
The Dashboard page is used to display detailed information about the device.
The Dashboard is only visible in the application bar if the Show 'Dashboard' option is enabled
by a service-level user in the Configuration -> Web Interface -> Appearance page.

10 en | Operation via the browser AUTODOME IP starlight 5000i
2019-11 | 1.2 | User Manual Bosch Security Systems
3 Operation via the browser
3.1 Live page
3.1.1 Connection
Stream 1
Select this option to display stream 1 of the camera.
Stream 2
Select this option to display stream 2 of the camera.
M-JPEG
Select this option to display the M-JPEG stream of the camera.
3.1.2 PTZ
Pan and tilt controls
– To tilt the camera up: Click and hold the up arrow.
– To tilt the camera down: Click and hold the down arrow.
– To pan the camera left: Click and hold the left arrow.
– To pan the camera right: Click and hold the right arrow.
– To pan and tilt the camera at the same time (variable pan/tilt): Click and drag the center
area (that resembles a point stick or a trackball on a computer keyboard) around the PTZ
control in the direction that you want to move the camera.
Zoom
Click the + button to zoom in.
Click the - button to zoom out.
Iris
Click (Iris close) to close the iris.
Click (Iris open) to open the iris.
Focus
Click to focus near.
Click to focus far.
3.1.3 Pre-positions
The camera displays Pre-position 1 through Pre-position 6. Select the appropriate pre-
position to view the video image for that pre-position/scene. In the lower left of the video
image, the OSD displays the Camera number (title), the Pre-position number, and the Pre-
position number stored.
Below the list of pre-positions/scenes is a drop-down list showing the stored pre-positions/
scenes.
Select the appropriate pre-position (1 through 6). Click to store the pre-position.
Note: If the pre-position is already stored, a dialog box displays the message, “Overwrite
current pre-position?” Click OK to overwrite, or click Cancel to cancel the operation.
Click to display the selected pre-position in the video image.

AUTODOME IP starlight 5000i Operation via the browser | en 11
Bosch Security Systems User Manual 2019-11 | 1.2 |
3.1.4 AUX Control
With the tab AUX Control you can enter pre-programmed keyboard control commands. These
commands are composed of a command number plus the appropriate function key (Show pre-
position, Set pre-position, AUX on, or AUX off). A valid combination either issues a command
to the device or displays an on-screen menu.
(Refer to the “AUX Commands” section of the manual for a list of all AUX commands for your
camera.)
Show pre-position
Click this button to display a pre-position.
Set pre-position
Click this button to set a pre-position.
AUX on
Click this button to activate an AUX command.
AUX off
Click this button to deactivate an AUX command.
3.1.5 Digital I/O
(only for cameras with alarm connections)
Depending on the configuration of the unit, the alarm input and the output are displayed next
to the image. Expand the Digital I/O group if necessary.
The alarm symbol is for information and indicates the status of an alarm input:
– The symbol lights when the input alarm is active.
The alarm output allows the operation of an external device (for example, a light or a door
opener).
– To activate the output, click the checkmark symbol.
– The symbol lights when the output is activated.
Input 1
This parameter identifies the first alarm input.
Input 2
This parameter identifies the second alarm input.
Output 1
Click the checkmark icon to enable the output. The checkmark becomes green.
Note: You can change the name of an alarm input in Configuration > Interfaces > Alarm
Inputs > Input 1 (or Input 2) > Name.
You can change the name of an alarm output in Configuration > Interfaces > Alarm Outputs >
Output name.
3.1.6 Special Functions
Tour A / Tour B
Click one of these buttons to start the continuous playback of a recorded (guard) tour. A
recorded tour saves all manual camera movements made during the recording, including its
rate of pan, tilt and zoom speeds, and other lens setting changes.
To stop a tour, click a directional control in the View Control tab.
Find home
Click this button to trigger the camera to seek its home position. The OSD displays the
message, “OSD: Finding Home Position.”
Focus
Click this button to activate the Auto Focus One Push mode on the camera.

12 en | Operation via the browser AUTODOME IP starlight 5000i
2019-11 | 1.2 | User Manual Bosch Security Systems
The OSD displays the message, “Auto Focus: ONE PUSH.”
Nightmode
Click this button to activate/deactivate night mode for the camera. After a few seconds, the
camera switches modes.
Custom tour
Click this button to view (in continuous playback) a custom tour that was previously
configured.
To stop a tour, click a directional control in the PTZ section of the page.
3.1.7 Recording status
The hard drive icon below the live camera image changes during an automatic recording.
The icon lights up and displays a moving graphic to indicate a running recording. If no
recording is taking place, a static icon is displayed.
3.1.8 Saving snapshots
Individual images from the displayed live video stream can be saved locally in JPEG format on
the computer's hard drive. The storage location depends on the configuration of the camera.
– Click the photo camera icon to save a single image.
3.1.9 Recording live video
Video sequences from the displayed live video stream can be saved locally on the computer's
hard drive. The sequences are recorded at the resolution specified in the encoder
configuration. The storage location depends on the configuration of the camera.
1. Click the recording icon to record video sequences.
– Saving begins immediately. The red dot on the icon indicates that a recording is in
progress.
2. Click the recording icon again to stop recording.
3.1.10 Full-screen display
Click the full-screen icon to view the selected stream in full-screen mode; press Esc
on the keyboard to return to the normal viewing window.
3.1.11 Audio communication
Audio can be sent and received via the Live page if the unit and the computer support audio.
1. Press and hold the F12 key on the keyboard to send an audio signal to the unit.
2. Release the key to stop sending audio.
All connected users receive audio signals sent from the unit but only the user who first
pressed the F12 key can send audio signals; others must wait for the first user to release the
key.
3.1.12 Storage, CPU and network status
When accessing the unit with a browser, the local storage, processor and network status
icons are shown in the upper right of the window.
When a local storage card is available, the memory card icon changes color (green, orange or
red) to indicate the local storage activity. If you hover over this icon with the mouse the
storage activity is shown as a percentage.

AUTODOME IP starlight 5000i Operation via the browser | en 13
Bosch Security Systems User Manual 2019-11 | 1.2 |
If you hover over the middle icon, the CPU load is shown.
If you hover over the right-hand icon, the network load is shown.
This information can help with problem solving or when fine tuning the unit. For example:
– if the storage activity is too high, change the recording profile,
– if the CPU load is too big, change the VCA settings,
– if the network load is too big, change the encoder profile to reduce bitrate.
3.1.13 Status icons
Various overlays in the video image provide important status information. The overlays provide
the following information:
Decoding error
The frame might show artifacts due to decoding errors.
Alarm flag
Indicates that an alarm has occurred.
Communication error
A communication error, such as a connection failure to the storage medium, a protocol
violation or a timeout, is indicated by this icon.
Gap
Indicates a gap in the recorded video.
Watermark valid
The watermark set on the media item is valid. The color of the check mark changes according
to the video authentication method that has been selected.
Watermark invalid
Indicates that the watermark is not valid.
Motion alarm
Indicates that a motion alarm has occurred.
Storage discovery
Indicates that recorded video is being retrieved.
3.2 Playback via browser
Click Playback in the application bar to view, search or export recordings. This link is
only visible if a direct iSCSI or memory card has been configured for recording. (With VRM
recording this option is not active.)
The panel on the left has four groups:
–Connection
–Search
–Export
–Track list

14 en | Operation via the browser AUTODOME IP starlight 5000i
2019-11 | 1.2 | User Manual Bosch Security Systems
3.2.1 Selecting the recording stream
On the left side of the browser, expand the Connection group if necessary.
To view a recording stream:
1. Click the Recording drop-down arrow to see the options.
2. Select recording stream 1 or 2.
3.2.2 Searching for recorded video
On the left side of the browser, expand the Search group if necessary.
1. To limit the search to a particular time range, enter the date and times for the start and
stop points.
2. Select an option from the drop-down box to define a search parameter.
3. Click Start Search.
4. The results are shown.
5. Click a result to play it back.
6. Click Back to define a new search.
3.2.3 Exporting recorded video
On the left side of the browser, expand the Export group if necessary.
1. Select a track in the track list or in the search results (or click on the timeline below the
video window and drag the buttons to mark the sequence you want to export).
2. The start and stop date and time are filled-in for the selected track. If required, change
the times.
3. In the Time lapse drop-down box, select the original or a condensed speed.
4. In the Location drop-down box, select a target.
5. Click Export to save the video track.
Note:
The target server address is set on the Network / Accounts page.
3.2.4 Controlling playback
The time bar below the video image allows quick orientation. The time interval associated with
the sequence is displayed in the bar in gray. Arrows indicate the position of the image
currently being played back within the sequence.
The time bar offers various options for navigation in and between sequences.
– If required, click in the bar at the point in time at which the playback should begin.
– Change the time interval displayed by clicking the plus or minus icons or use the mouse
scroll wheel. The display can span a range from six months to one minute.
– Click the alarm jump buttons to go from one alarm event to the next or to the previous
one. Red bars indicate the points in time where alarms were triggered.
Controls
Control playback by means of the buttons below the video image.
The buttons have the following functions:
– Start/Pause playback
– Select the playback (forward or backward) speed using the speed regulator
– Step forward or backward frame-by-frame when paused (small arrows)

AUTODOME IP starlight 5000i General | en 15
Bosch Security Systems User Manual 2019-11 | 1.2 |
4 General
4.1 Identification
Device name
Enter a unique, unambiguous name for the device (for example, the installation location of the
device). This name should be easy to identify in a list of devices in your system. The device
name is used for the remote identification of a unit, such as in the event of an alarm.
Do not use any special characters, for example &, in the name. Special characters are not
supported by the system's internal management.
Device ID
Enter a unique identifier for the device. This ID is additional identification for the device.
Host naming
Enter a host name.
Initiator extension
Add text to an initiator name to make identification easier in large iSCSI systems. This text is
added to the initiator name, separated from it by a full stop. (You can see the initiator name in
the System Overview page.)
4.2 User Management
The section Allowed authentication modes provides information about the authentication
modes set in the camera. A checkmark appears in the checkbox to the left of the mode if the
mode is set. If the mode is not set, the phrase, “No certificate installed” appears to the right
of the mode name.
Password
This field indicates if a password is set for the camera.
Certificate
A check mark in this check box indicates that at least one certificate is loaded onto the
camera. If no certificates are loaded, then “No certificate installed” appears to the right of the
text.
The Escrypt certificate is a root certificate for Bosch Security Systems that proves that the
device meets the following criteria:
– It originates from a Bosch factory that is a secure environment.
– It has not been tampered with.
Escrypt is a Bosch company and Certificate Authority (CA).
Active directory server (ADFS)
A check mark in this check box indicates that the camera uses an active directory server. If the
camera does not use ADFS, then “No certificate installed” appears to the right of the text.
Password management
A password prevents unauthorized access to the device. You can use different authorization
levels to limit access.
Proper password protection is only guaranteed when all higher authorization levels are also
protected with a password. Therefore, you must always start from the highest authorization
level when assigning passwords.
You can define and change a password for each authorization level if you are logged into the
“service” user account.
The device has three authorization levels: service, user, and live.
– service is the highest authorization level. Entering the correct password gives access to
all the functions and allows all configuration settings to be changed.

16 en | General AUTODOME IP starlight 5000i
2019-11 | 1.2 | User Manual Bosch Security Systems
– user is the middle authorization level. At this level you can operate the device, play back
recordings, and also control camera, for example, but you cannot change the
configuration.
– live is the lowest authorization level. At this level you can only view the live video image
and switch between the different live image displays.
To edit a password
To edit a password, click the pencil icon to the right of the column Type for the appropriate
User name.
To create a new user
To create a new user, click Add.
In the box User, fill in the fields. For Group, select the appropriate authorization level. For
Type, select either Password (for a new password) or Certificate (for a certificate that the
new user is authorized to use).
Note: Use a maximum of 19 characters. Do no use special characters.
Confirm password
In each case, enter the new password a second time to eliminate typing mistakes.
Notice!
A new password is only saved when you click the Set button. You should therefore click the
Set button immediately after entering and confirming a password.
4.3 Date/Time
Date format
Select the required date format from the dropdown menu.
Device date/Device time
Notice!
Make sure that recording is stopped before synching to the PC.
If there are multiple devices operating in your system or network, it is important to
synchronize their internal clocks. For example, it is only possible to identify and correctly
evaluate simultaneous recordings when all units are operating on the same time.
1. Enter the current date. Since the unit time is controlled by the internal clock, there is no
need to enter the day of the week - it is added automatically.
2. Enter the current time or click the Sync to PC button to copy your computer's system
time to the camera.
Note: It is important that the date/time is correct for recording. An incorrect date/time setting
could prevent correct recording.
Device time zone
Select the time zone in which the system is located.
Daylight saving time
The internal clock can switch automatically between normal and daylight saving time (DST).
The unit already contains the data for DST switch-overs for many years in advance. If the date,
time and zone have been set up correctly, a DST table is automatically created.
If you decide to create alternative daylight saving time dates by editing the table, note that
values occur in linked pairs (DST start and end dates).

AUTODOME IP starlight 5000i General | en 17
Bosch Security Systems User Manual 2019-11 | 1.2 |
First, check the time zone setting. If it is not correct, select the appropriate time zone and
click Set.
1. Click Details to edit the DST table.
2. Select the region or the city which is closest to the system's location from the list box
below the table.
3. Click Generate to fill the table with the preset values from the unit.
4. Click one of the entries in the table to make changes. The entry is highlighted.
5. Click Delete to remove the entry from the table.
6. Choose other values from the list boxes under the table, to change the selected entry.
Changes are immediate.
7. If there are empty lines at the bottom of the table, for example after deletions, add new
data by marking the row and selecting values from the list boxes.
8. When finished, click OK to save and activate the table.
Time server address
The camera can receive the time signal from time server using various time server protocols,
and then use it to set the internal clock. The unit polls the time signal automatically once every
minute.
Enter the IP address of a time server here.
You can choose to have the DHCP server give a time server date by selecting the Overwrite by
DHCP option.
Time server type
Select the protocol that is supported by the selected time server.
– Select Time protocol if the server uses the protocol RFC868.
– The SNTP protocol supports a high level of accuracy and is required for special
applications and subsequent function extensions.
– Select TLS protocol if the server uses the RFC 5246 protocol.
– Select Off to disable the time server.
Click Set to apply the changes.
4.4 Display Stamping
Various overlays or “stamps” in the video image provide important supplementary information.
These overlays can be enabled individually and are arranged on the image in a clear manner.
Camera name stamping
This field sets the position of the camera name overlay. It can be displayed at the Top, at the
Bottom or at a position of your choice that you can then specify using the Custom option. Or
it can be set to Off for no overlay information.
1. Select the desired option from the list.
2. If you select the Custom option, additional fields are displayed where you can specify the
exact position (Position (XY)).
3. In the Position (XY) fields, enter the values for the desired position.
Optionally, tick the Underlay with full-width black bar box to place a black bar beneath the
time stamp.
Logo
To place a logo on the image, select and upload an uncompressed .bmp file with a maximum
size of 128x128 pixels and 256 colors to the camera. Its position on the image can then be
selected.

18 en | General AUTODOME IP starlight 5000i
2019-11 | 1.2 | User Manual Bosch Security Systems
Logo position
Select the position for the logo on the OSD: To the left of the name, To the right of the
name, or Logo only.
Select Off (the default value) to disable logo positioning.
Time stamping
This field sets the position of the time overlay. It can be displayed at the Top, at the Bottom or
at a position of your choice that you can then specify using the Custom option. Or it can be
set to Off for no overlay information.
1. Select the desired option from the list.
2. If you select the Custom option, additional fields are displayed where you can specify the
exact position (Position (XY)).
3. In the Position (XY) fields, enter the values for the desired position.
Display milliseconds
If necessary, you can also display milliseconds. This information can be useful for recorded
video images; however, it does increase the processor's computing time. Select Off if you do
not need to display milliseconds.
Live video indicator
Select On to display the Live video indicator, an icon that pulses on the OSD to show that the
video stream is live.
Select Off to hide the Live video indicator.
Alarm mode stamping
Select On to display a text message overlay in the image in the event of an alarm. It can be
displayed at a position of your choice that you can then specify using the Custom option. Or it
can be set to Off for no overlay information.
1. Select the desired option from the list.
2. If you select the Custom option, additional fields are displayed where you can specify the
exact position (Position (XY)).
3. In the Position (XY) fields, enter the values for the desired position.
Alarm message
Enter the message to be displayed in the image in the event of an alarm. The maximum text
length is 31 characters.
Title OSD
OSD titles can be displayed at a position of your choice.
Select On to display sector or pre-position title overlays continuously in the image.
Select Momentary to display sector or pre-position title overlays for a few seconds.
1. Select the desired option from the list.
2. Specify the exact position (Position (XY)).
3. In the Position (XY) fields, enter the values for the desired position.
Select Off to deactivate the display of overlay information.
Camera OSD
Select On to momentarily display camera response information, such as Digital Zoom, Iris
open/close, and Focus near/far overlays in the image. Select Off to display no information.
1. Select the desired option from the list.
2. Specify the exact position (Position (XY)).
3. In the Position (XY) fields, enter the values for the desired position.
Title region
Select On to set or to edit the position of the title region on the OSD.

AUTODOME IP starlight 5000i General | en 19
Bosch Security Systems User Manual 2019-11 | 1.2 |
The fields Position (XY) and (0...255) appear.
1. In the field Position (XY), specify the exact position. (The default is 10.)
2. In the field (0...255), enter the position range. (The default is 176).
Select Off to hide the region from view.
Telemetry region
Select On to set or to edit the position of the telemetry information (azimuth and elevation
(pan/tilt position)) and the zoom factor on the OSD. Refer to the section ”PTZ Settings, page
36“ to set the pan and tilt limits.
The fields Position (XY) and (0...255) appear.
1. In the field Position (XY), specify the exact position. (The default is 10.)
2. In the field (0...255), enter the position range. (The default is 176).
Select Off to hide the region from view.
Feedback region
Select On to set or to edit the position of system feedback messages (including message for
camera settings such as focus, iris, and zoom level) on the OSD. Refer to the section “Lens
Settings” to configure these settings.
The fields Position (XY) and (0...255) appear.
1. In the field Position (XY), specify the exact position. (The default is 10.)
2. In the field (0...255), enter the position range. (The default is 176).
Select Off to hide the region from view.
Transparent background
Check this box to make transparent the stamp background on the image.
Stamping size
Select the desired font size of the overlays on the OSD: Normal or Large.
Text color
Select the color for the alarm message to be displayed in.
Background color
Select the background color for the alarm message to be displayed in.
If you have enabled the Transparent background option, the background color is not
displayed in the OSD.
Video authentication
Select from the Video authentication drop-down box a method for verifying the integrity of
the video.
If you select Watermarking, all images are marked with an icon. The icon indicates if the
sequence (live or saved) has been manipulated.
If you want to add a digital signature to the transmitted video images to ensure their integrity,
select one of the cryptographic algorithms for this signature.
Signature interval [s]
For certain Video authentication modes, enter the interval (in seconds) between insertions of
the digital signature.
4.5 GB/T 28181
This page allows you to set the parameters for conformance to the GB/T28181 national
standard “Security and protection video monitoring network system for information transport,
switch and control”. This standard is specifically for China.

20 en | General AUTODOME IP starlight 5000i
2019-11 | 1.2 | User Manual Bosch Security Systems
Enable
Select this checkbox to enable the system to use the other parameters on this page in
accordance with the GB/T 28181 national standard.
H.264 elementary stream
Select this checkbox to select or to enable the H.264 elementary stream.
Registration timeout
Enter a value (in milliseconds) for the registration timeout. The default is 3600.
Heartbeat timeout
Enter the value (in seconds) for the heartbeat timeout. The default is 15.
Server ID
Enter the ID of the server.
Server IP address
Enter the server IP address.
Server port
Enter the number of the server port. The default is 0.
Device ID
Enter the ID of the device.
Device port
Enter the number of the device port. The default is 5060.
Password
Enter the appropriate password.
Alarm device ID
Enter the ID of the alarm device.