Boss Audio Systems 624B User manual

4

DSP
LOC
LOUD
DSP
LOC
LOUD
CAR RADIO RECEIVER / MP3 PLAYER
WITH BULETOOTH HAND FREE SYSTEM
INSTRUCTION MANUAL
LOUD
BUTTON
AUDIO
BUTTON
MENU
BUTTON
INFO
BUTTON
BAND
BUTTON
LCD
DISPLAY
PLAY/
PAUSE
BUTTON
INTRO
SCAN
BUTTON
REPEAT
BUTTON
RANDOM
BUTTON
ENCODER
VOLUME
KNOB
MUTE
BUTTON
EQ
BUTTON
POWER
BUTTON
PRESET MEMORY STATION BUTTONS
(M1-M6)
AMS
BUTTON
TUNING /
SEEK
UP/DOWN
NEXT/BACK
BUTTON
TALK
BUTTON
CANCEL/
SRC
BUTTON
INFRARED
REMOTE
SENSOR
10+/- FOLDER
UP / DOWN
BUTTONS
C
C
C

E - 1
INSTALLATION
Before final installation, connect the wiring temporarily and make sure it is all working
properly.
Use only the parts included with the unit to ensure proper installation. The use of
unauthorized parts can cause malfunctions.
This item must be installed by an authorized dealer in order to keep the warranty vaild.
Install the unit where it does not get in the driver's way and cannot injure the passenger if
there is a sudden stop, like an emergency stop.
If installation angle exceeds 30 degrees, the unit might not give its optimum performance.
Avoid installing the unit where it would be subject to high temperature, such as direct
sunlight, or hot air, heater or where it would be subject to dust dirt or excessive vibration.
Be sure to remove the front panel before installing the unit.
DIN FRONT/REAR-MOUNT
This unit can be property installed either from Front (conventional DIN Front-mount) or Rear
(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis).
For details, refer to the following illustrated installation methods A and B.
- DIN FRONT-MOUNT (Method A)
Installation the unit
1. Dashboard
2. Holder
After inserting the half sleeve into the
dashboard, select the appropriate tab
according to the thickness of the
dashboard material and bend them
inwards to secure the holder in place.
182
53
12
a. Frame
b. Insert fingers into the groove in the
front of frame and pull out to remove
the frame. (When re-attaching the
frame, point the side with a groove
down wards and attach it.)
c. Insert the levers supplied with the
unit into the grooves at both sides of
the unit as shown in figure until they
click. Pulling the levers makes it
possible to remove the unit from the
dashboard.
Removing the unit
a
b
c
30

- DIN REAR-MOUNT (METHOD B)
Installation using the screw holes on the sides of the unit.
Fastening the unit to the factory radio mounting bracket.
1. Select a position where the screw
holes of the bracket and the screw
holes of the main unit become
aligned (are fitted) and tighten the
screws at 2 places on each side.
2. Screw
3. Factory radio mounting bracket.
4. Dashboard or Console
5. Hook (Remove this part)
Note: the mounting box, outer trim ring,
and half-sleeve are not used for method
B installation.
E - 2
2. DETACHABLE CONTROL PANEL (D.C.P.)
Removing The Detachable Control Panel (D.C.P.).
1. Turn the power off
2. Press the D.C.P. release button
3. Remove the D.C.P.
PANEL RELEASE
BUTTON
B
A
2
Attaching the DCP
CAUTION
1. Attach the panel at the right side first, with
point B on the main unit touching point A on
the D.C.P. (As shown on the diagram).
2. Then press the left side of D.C.P. onto the
main unit until a click sound is heard.
DO NOT insert the D.C.P from the left side. Doing so may damage it.
The D.C.P can easily be damaged by shocks. After removing it, place it in a protective case
and be careful not to drop it or subject it to strong shocks.
When the release button is pressed and the D.C.P is unlocked, the car's vibrations may
cause it to fall. To prevent damage to the D.C.P, always store it in a protective case after
detaching it.
The rear connector that connects the main unit and the D.C.P is an extremely important
part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.
Socket
Note:
If the D.C.P is dirty, wipe off the dirt with soft, dry cloth
only. And use a cotton swab soaked in isopropyl
alcohol to clean the socket on the back of the D.C.P.
5
2
4
3
25

DETACHABLE CONTROL PANEL (D.C.P.)
Removing The Detachable Control Panel (D.C.P.).
CAUTION
DO NOT insert the D.C.P from the left side. Doing so may damage it.
The D.C.P can easily be damaged by shocks. After removing it, place it in a protective case and
be careful not to drop it or subject it to strong shocks.
When the release button is pressed and the D.C.P is unlocked, the car's vibrations may cause it
to fall. To prevent damage to the D.C.P, always store it in a protective case after detaching it.
The rear connector that connects the main unit and the D.C.P is an extremely important part. Be
careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.
Attaching the Detachable Control panel (D.C.P.)
1. Insert the right side of the D.C.P. Into
the main unit.
NOTE: The D.C.P. Must be attached into
the T-Joint.
2. Press the D.C.P. On to the left side of
middle of D.C.P. Until a click sound is
heard.
2.
1.
RELEASE
BUTTON
D.C.P.
PUSH
Note:
If the D.C.P is dirty, wipe off the dirt with soft,
dry cloth only. And use a cotton swab soaked
in isopropyl alcohol to clean the socket on the
back of the D.C.P.
Socket
1. Turn the Power off.
2. Press the Panel Release Button.
3. Remove the D.C.P.
E - 3

E - 4
ELECTRICAL CONNECTION
a. Make sure your car battery is a 12 volt (6 filler caps) negative ground system (if not, a
converter will be necessary).
b. Before starting wiring connections, disconnect the power supply by removing the fuse
from the fuse box.
c. Connect the power wire to one of the extra terminals of the fuse box.
d. Connect the black ground wire to a metal part of the car. It is important to make good
contact.
e. Make other wiring connections as shown.
f. If your car does not have ISO connector, you can procure it from any car accessory shop.
Notes: INCORRECT WIRING OR OPERATION WILL AVOID THE WARRANTY OF THIS UNIT.
(CAR UNIT BACK SIDE) FUSE
Fuse Replacement:
To replace the fuse, pull out the blown fuse
from the socket. Insert a new one with same
rating
GENERAL OPERATION
POWER ON/OFF BUTTON ( )
Press POWER button or any other button on the front of the radio to turn the unit on.
Press POWER button again to turn the unit off.
MUTE BUTTON
Press the mute button momentarily to mute the audio volume, and "Mute" will in the
display. Press the mute button again to restore volume to the previous setting.
AUDIO SELECT BUTTON
Press this button to select desired audio function.
VOLUME (VOL)->BASS (BAS)-> TREBLE (TRE)-> BALANCE (BAL)-> FADER (FAD)
Rotate Volume Control to adjust desired level within 3 seconds.
MENU BUTTON
Press MENU Button to navigate through the menu items, while the desired menu item is
displayed, use Volume control to adjust the selected function:
- LOC/ DX MODE
/
Use this mode to change between Local and Distant (DX) tuning mode. Local mode
improves reception in some areas where the signal is too strong.
Under clock display mode.press MENU button until the LCD flashes.
Rotate the volume knob in clockwise direction to adjust hour, other direction to adjust minute.
- CLOCK ADJUST
BEEP OFF: disable audible beep tone when any function is accessed.
BEEP ON: enable audible beep tone.
- BEEP MODE (BEEP ON / OFF)

EQ BUTTON (PRESET EQUALIZER)
SRC BUTTON
Press this button to select different sources , sequence as follow:
SOURCES PRIORITY
A) Tuner mode (Radio)
B) USB (only if a USB drive is inserted)
C) SD / MMC (only if a SD or MMC card is inserted))
D) AUX IN
E) BT MODE (only if unit is paired to a mobile phone)
Whenever a USB or SD/MMC is being inserted, unit will automatically switch to USB or
SD/MMC mode, does not matter the unit is currently in what mode.
When in USB or SD / MMC mode, if the USB or SD / MMC is being removed, unit will
automatically switch to radio mode.
FRONT AUX INPUT
INFO BUTTON
At Radio mode Press this button to view frequency of the station in listening and clock time .
At DSP off mode preset equalizer will be controlled by Bass / Treble setting.
ENCODER VOLUME KNOB
When the Menu function is not activated, rotate this knob to change the volume level.
When Menu function is activated, rotate this knob to navigate through different menu items.
Connect the external signal to the front 3.5mm earphone jack on front panel, then press
Mode button to select Aux mode. Press Mode button again to cancel Aux Mode and return
to previous mode.
DSP OFF->CLASSIC->POP->ROCK
E - 5
LOUDNESS BUTTON
Use this LOUDNESS control to increase bass output.

Press this button to search for radio stations.
BAND BUTTON
The RESET button is located on the front panel (as shown on the diagram). To press it vertically
with a ballpoint pen or metal object will activate it. The reset button is to be activated for the
following reasons:
RESET BUTTON
LIQUID CRYSTAL DISPLAY PANEL (LCD)
The LCD panel display the frequency, time and activated functions.
NOTE:
It is a characteristic of LCD panel that if subjected to cold temperatures for an extended period
of time, they will take longer time to illuminate than under normal conditions, in addition, the
visibility of the numbers on the LCD may slightly decrease. The LCD read-out will return to
normal when temperatures increase to a normal range.
STATION PRESET BUTTONS (M1-M6)
You can store & recall six preset radio stations by pressing M1-M6 buttons
TO STORE A STATION: 1) select a band (if needed)
2) select a station by tuning up / down button
3) hold a preset button which you want store the station for at least 2
seconds. The preset number will appear on the display
accompanied by a beeps sound.
TO RECALL A STATION: 1) select a band (if needed)
2) press a preset button briefly to recall the stored station.
Initial installation of the unit when all wiring is completed.
All the function buttons do not operate.
Error symbol on the display.
Note: If the unit cannot function normally after reseting, please use a cotton swab soaked in
isopropyl alcohol to clean the socket on the back of the control panel.
E - 6
TUNING UP / DOWN BUTTON ( )
Press this button to change between bands FM1,FM2,FM3, MW1,MW2(AM).
AUTO MEMORY STORE/PRESET SCAN BUTTON (AMS)
1.PRESET SCAN: Press AMS button briefly enter Preset Scan mode, it will scan all the preset
stations in the memories, you can hear that will stay on each station for about 10 seconds.
2.AUTO MEMORY STORE: Press AMS button long to enter Auto Store mode, this feature will
automatically scan the current band and enter up to 6 strongest stations into the 6 preset
memories. To stop Auto Store & Scan, press the AMS button again.

E - 7
M1)PLAY/PAUSE AND FIRST TRACK BUTTON
M4)RANDOM PLAY BUTTON
INTRO SCAN BUTTON
TRACK UP AND TRACK DOWN BUT TON ( )
When random play mode is selected, the tracks will be played in random order, press this key
one more time to cancel random play mode.
Press this button to select Intro Scan function, the first 10 seconds of each track will be played
sequentially until this button is pressed again, then normal play will resume at the current track.
Under normal play mode, press the Track Up Button for less than 1 second to skip the
playback to the next track, or press the Track Down Button for less than 1 seconds to return to
the beginning of the current track, press this button one more time to skip to the previous
track.
When any of these buttons is pressed for more than 1 second, the Mp3 player will enter
Cue/Review mode, this is indicated by the flashing track number on the LCD. When the key is
released, normal play will resume.
Press this button briefly to pause MP3 play, press again to release pause.
M3)REPEAT BUTTON
Pressing this button will activate Repeat Function in the following order :
Repeat On Repeat Off
M2)
MP3/SD/USB OPERATIONS

MMC/SD CARD & USB DEVICE OPERATIONS
START THE USB DEVICE MODE
1.The USB socket is accessible as indicated in picture
1.(P.1)
2.Plug in the USB drive / device completely as indicated
in picture 2(P.2) and display will show USB-LOAD to
indicate that the USB drive / device is being plugged in
correctly & the download has begun.
3.Does not matter which source the unit is in
(TUNER,SD/MMC,AUX,BT,etc), once a USB drive / device
is being plugged into the unit, unit will automatically
switch to USB mode.
4.All the USB files playback function is same as normal
MP3 files playback.
1.Always unplugged the USB gently from the unit,
excessive force used will cause permanent & serious
damage to the unit & the USB drive / device.
TO STOP USB PLAYBACK
1.If the USB drive / device is unplugged, the unit will automatically switch to radio mode.
Or user can use SRC button to switch to other mode.
2.User can use the SRC button to choose USB mode (only if USB drive / device is
inserted in the unit ) or any other modes, when they are in any mode.
CAUTION
COMPATIBILITY
Due to the fast changing technology world, this unit may or
may not be compatible to all the USB drive / device
available with all the future technology, especially those
USB drive / device which require to install a driver. Always
choose a compatible USB drive / device which is
compatible with this unit.
Warning: Excessive weight or size USB drive/device
may cause permanent & serious damage to the unit and
may cause access to the buttons on the front panel
impossible. User must use an extension cable (provide
by USB device manufacturer) to connect with USB
socket to prevent any damage cause.
USB SPECIFICATION
* SUPPORT MAX 32G USB FLASH MEMORY
* SUPPORT MAX 9999 SONGS
* USB 1.1 DEVICE SUPPORT
* USB 2.0 DEVICE SUPPORT
(TRANSFER SPEED SAME AS VER 1.1)
* FILE MANAGER: FAT12/FAT16/FAT32
* CURRENT SUPPLY: MAX 500mA
NOTE:
This unit is not compatible with portable Hard-Disc.
E - 8