Boston Acoustics DT6000 User manual

DigitalTheater™6000
Integrated Home Theater System with Dolby®Digital Surround
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 1

Important Safety Instructions
This symbol found on thepower supply indicates double insulation.
Thissymbol found on the powersupply indicatesthe user should read allsafety statements
found in the user manual.
This symbol foundon thepower supply indicateshazards arising from dangerous voltages.
Warning! To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture.
Power supply intended for use withBoston Acoustics speaker systemsonly!
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only withdamp cloth.
7. Do notblock any of the ventilation openings.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other appa-
ratus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the
polarized or grounding type plug. A polarized
plug has two bladeswith one wider than the
other. A grounding typeplug has two blades
and a third grounding prong. The wide blade or
the third prong are provided for your safety.
When the provided plug does not fit into your
outlet, consult an electrician for replacement of
the obsolete outlet.
10. Only use attachments/accessories specified
by the manufacturer.
11. Unplug this apparatusduring lightning
storms or when unused for long periods of
time.
12. Refer all servicing to qualified service per-
sonnel. Servicing is required when the appara-
tus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatushas been exposedto
rain or moisture,does not operate normally, or
has been dropped.
13. Caution! Do not short output jack of power
supply!
2
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 2

3
Important Safety Information
American Users:
This equipment hasbeen tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
Rules. These limitsare designedto provide rea-
sonable protection againstharmful interference
in a residential installation. This equipment gen-
erates, usesand can radiate radio frequency
energyand, if not installed and usedin accor-
dance with the instructions, may cause harmful
interference to radio or television reception.
However, there is no guarantee that interfer-
ence will not occur in
a particular installation. If this equipment does
cause harmful interference toradio or television
reception, which can be determined by turning
the equipment off and on, the user is encour-
aged to try to correct the interference by one or
more ofthe following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equip-
ment and receiver.
3. Connect the equipment into anoutlet on a
circuit different from that to which thereceiver is
connected.
4. Consult the dealer or an experienced
radio/TV technician for help.
Canadian Users:
This digital apparatus doesnot
exceed the ClassB limits for radio noise emis-
sions from digital apparatus as set out in the
radio interference regulations of Industry
Canada.
Caution! Disconnect power before servicing.
Le présent appareil numérique n'émet pas de
bruits radioélectriquesdépassant les limites
applicables aux appareils numériques de Classe
B prescrites dans le règlementsur lebrouillage
radioélectrique édictépar Industrie Canada.
Attention! Couper le courant avant'entretien.
Declaration of Conformity
Konformitätserklärung
Déclaration de Conformité
Declaración de Conformidad
Verklaring de Overeenstemming
Dichiarazionedi Conformità
We/Wir/ Nous/WIJ/Noi:
Regulatory Compliance Statements
1. Power supply intended for indooruse only!
2.Power supply intended for use with Boston Acoustics speaker systems only!
3.CAUTION! Do notshort output of power supply!
4. Do notplace power supply near heat generating sources!
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 3

4
Boston Acoustics, Inc. 300 Jubilee Drive
Peabody, MA 01960 USA
declare under our sole responsibility thatthe
product
erklären, inalleniniger Verantwortung, daß
dieses Produkt,
déclarons sousnotre seule responsabilité que
le produit,
declaramos,bajo nuestra sola responsabilidad,
que el producto,
verklaren onder onzeverantwoordeijkheid, dat
het product,
dichiariamo sotto nostra unica responsabilità,
che il prodotto,
DigitalTheater™ 6000 System
to which this declaration relates,is in conformi-
ty with the following standardsor other norma-
tive documents:
auf das sich diese Erklärung bezieht,mit
der/den folgenden Norm(en) oder Richtlinie(n)
übereinstimmt:
auquel se réfère cettedéclaration est conforme
à la (aux) norme(s) ou au(x) document(s) nor-
matif(s):
al que se refiere estadeclaración es conforme
a la(s) norma(s) u otro(s) documento(s) normati-
vo(s):
waarnaar deze verklaring verwijst, aan de
volende noem(en) of richtlijn(en) beantwoordt:
a cui si riferisce questa dichiarazione è con-
forme alla/e sehuente/i norma/o documento/i
normativo/i:
European Users:
This InformationTechnology
Equipment has been tested and found to
comply with the following European directive:
(i) EMC Directive89/336/EEC amendingdirec-
tive 92/31/EEC 93/68 EEC as per
- EN 50081-1:1992 according to
EN55022: 1994/A1: 1995/A2: 1997 Class B
EN61000-3-2: 1995
EN61000-3-3: 1995
- EN50082-1: 1997 according to
EN61000-4-2: 1995
EN61000-4-3: 1997
ENV 50204: 1996
EN61000-4-6: 1996
EN61000-4-5: 1996
EN61000-4-11: 1996
EN61000-4-4: 1995
(ii) Low Voltage Directive (Safety) 72/23/EEC as
per EN60065: 1993
Regulatory Compliance Statements (cont.)
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 4

5
Japanese Users:
This equipment is in the Class 2 cate-
gory (Information Technology Equipment to be
used in a residential area or an adjacent area
thereto) and conformsto the standards setby
the Voluntary ControlCouncil for Interference
by Information Technology Equipment aimed at
preventing radio interference in such residential
areas.
When used near a radio or TV receiver, this
equipment may become thecause of radio
interference. Read the instructions for correct
handling.
Australian and New Zealand Users:
This device has been tested and found
to comply with the limits for a Class Bdigital
device, pursuant to the Australian/New Zealand
standard AS/NZS 3548 set out by the Spectrum
Management Agency.
Caution! Disconnect power beforeservicing.
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 5

6
This package contains —
Remote
“AAA” Batteries (4)
Subwoofer
Center channel speaker with display
Satellite speakers (4)
Satellite speaker wall-mount brackets (4)
Satellite speaker up-mount brackets (2)
15 ft (38cm) short front speaker cables (3)
50 ft (76cm) longsurround speaker cables (2)
Control cable
Digital input cable
Analog stereo input cable
Transformer and power cord assembly
Self-adhesive rubber feet for subwoofer (4)
Self-adhesive rubber pads for
speakers (4 x 5)
Wall-mount hardware
•
1
•
2
•
3
•
4
•
5
•
6
•
8
•
9
•
10
•
11
•
7
•
12
•
13
•
14
•
15
•
16
•
1
•
2•
3
•
4
•
5
•
6
•
8
•
9
•
10
•
11
•
7
•
12
•
13
•
14
•
15 •
16
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 6

7
Specifications
System Frequency Response (±3dB) 50-20,000Hz
Maximum System SPL 105dB at typical listening position
Dolby Digital Decoder 20-bit DSP
Inputs Digital (2): Coaxial and optical
Analog (2): Stereo RCA Jacks
Remote Control Universal remote control with 3 pre-programmed buttons for TV, VCR,
and Cable Box.
Display (Center Channel) 2 digits display master volumeand individual speaker trims; 4LEDs show
operational mode, 4 LEDS show input selected, and lower 6 LEDsshow
the active speakers in test tone andtrim level mode
Center Channel Drive Unit 31⁄2” (89mm), activelyequalized
Subwoofer Bass Unit 61⁄2” (165mm),actively equalized
Satellite Drive Units 31⁄2” (89mm), activelyequalized
Dimensions (H x W x D) Center Channel– 41⁄4x 65⁄8x 41⁄2” (107 x 167 x 110mm)
Subwoofer – 111⁄4x 7 x 143⁄4”(285 x 177 x 375mm)
Satellites – 41⁄2x 41⁄8x 43⁄4”(110 x 105x 120mm)
Weight Center Channel – 3 lbs. (1.3kg)
Subwoofer – 11 lbs. (5kg)
Satellites – 2 lbs. (0.8kg)
Finish Dark Gray
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 7

8
Dolby Digital Decoder
DigitalTheater 6000 uses a state-of-the-art
DolbyDigital decoder. Its acceptsa digital data
streamfromeither of two digital inputsor
converts either of two stereo analog inputs to
digital format.The digital data canbe either
encoded Dolby Digital or linear PCM data. The
decoderautomatically detects the difference.
Center Channel Unit
This integrated unit goes on topofthe TV and
houses the center speaker, an LED display, and
the infra-redremote control receiver.
DigitalTheater 6000 utilizes MagnaGuard®
magnetic shielding on all speakers to prevent
television picture interference or accidental
disk erasure.The pre-programmed universal
remote control operates the DigitalTheater
6000, and hundreds of different models of TVs,
VCRs andcable boxes.
DigitalTheater 6000 Subwoofer
The DigitalTheater 6000 Subwoofer provides
dramatic bass impact. It usesour long-excur-
sion 61⁄2-inch bass driver in a dual-chamber
bandpass enclosure. This advanced design
uses a sealed chamber for precise driver con-
trol and lowdistortion, and aventedchamber
to concentrate the output in the low bass
region. The result is a subwoofer that delivers
deep, clean bass from acompactenclosure.
DigitalTheater 6000 Satellites
The DigitalTheater 6000 system provides four
satellite speakers for the left and right front and
left and right rear channels. These speakerscan
be mounted on thewall, using thesupplied
wall-mounting brackets. Alternatively they can
be placed on a bookshelf or table-top using
the rubber feetprovided.
Description
The Boston DigitalTheater 6000 is an integrated home theater sound system. It accepts signals
from digital or analog sources, decodes them to produce surround sound for up to six channels
and provides the amplifiers and speakers for those six channels. The power section uses separate
actively-equalized amplifiers for each of the speakers, including the subwoofer. All that is needed
is a DVD player, digital DSS satelliteTV feed, or HiFi VCR, and a monitor or TV for a complete
hometheater system. The DigitalTheater 6000 delivers wide-range, high-fidelity sound from a
package that is easy to install and a pleasure to use.
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 8

9
Center Channel
Place theDigitalTheater 6000
center channel on topof the
video monitoror TV set. The
front of the speaker should
be flushwith the frontof the
television.
Subwoofer
The level of bass outputfrom the
subwoofer will vary at different posi-
tions in the room. Corner placement
provides the most bass output, while
placement nearonly one wall provides
somewhat less bass. Since low bass sounds are
omnidirectional—the earcan’t tellfrom which
direction they’re coming—the subwoofer can
be located outof sightin thecorner of the
room, yet all the sound, including the bass,
appears to come from the DigitalTheater
6000’s front speakers.
Front Satellite Speakers
The best locationfor the front speakersis
to either side of the video monitor or TV.
The speakerscan be wall-mounted, or placed
ona bookshelf, with equally good results.
Rear Satellite Speakers:
The best locationfor the rear speakers isto the
side and slightly behind the listeners. The
speakers can be wall-mounted facingout, as
shown. It may be easier to run wire to the
speakers if they are mountednear the floor,
facingup towards the ceiling. Thisposition will
produce excellent surround results. Mounting
brackets for both options are included.
How to Place the Boston DigitalTheater 6000 System
in Your Room
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 9

10
Drill two 7⁄16” (11mm) holesfor toggle wings.
If mountingona surface other than drywall,
consult aknowledgeable installerabout the
proper hardware to use on your wall.
If you are running speaker wire behind the
wall, drill a1⁄2” (12mm) hole 3⁄4” (19mm) below
the top toggle wing hole.
•
1
•
1
•
2
•
2
•
3Attach bracket to wall with machine screws
and toggle wings as shown.
Connect the speakerwire to the speaker.
Attach speaker bracket with flathead
machine screw.
•
4
•
4
•
5
•
5
•
3
Wall-mounting the satellite speakers
Facing Out
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 10

11
Attach bracketto speaker with the supplied
flathead machine screw.
Drill two 1⁄8” (3mm) pilotholes for wood
screws, then mount screws. Leave about 1⁄8”
(3mm) of screw thread exposed. If mounting
on drywall,use plasticanchors (not includ-
ed). Consult a knowledgeable installer
about the proper hardware to use on your
wall.
•
1
•
1
•
2
•
2
•
3If you are runningspeakerwire behind the
wall, drill a 1⁄2” (12mm) hole 1"(25mm)
below the top screw hole.
Connect the speaker wire to the speaker.
Slip the bracket/speaker assembly onto the
screws.
•
4
•
4
•
5
•
5
•
3
Facing Up
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 11

Plug oneof thetwo cords coming out of the transformer intothe subwoofer jack labeled 12V in
AC/DC andthe other AC power cord on the transformerintoan AC outlet.
12
Speaker Connection
Center Channel Speaker
Connect the shortspeakercable, withthe green RCAplug, between thegreen jack onthe
DigitalTheater 6000 subwoofermarked centerand the speakercable jack on the centerchannel
speaker.
Connect the control cable,withblue mini-DIN plug onboth ends,between thejack on the
DigitalTheater 6000 subwoofermarked controland the control cable jackon the center channel
speaker.
AC Power Connection
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 12

13
Plug thewhite plug of the shortspeaker
cable into the jack labeled left front.
Plug the red plug of the shortspeaker cable
into the jack labeled right front.
Plug the white plug of the long speaker
cable into thejack labeledleft rear.
Plug the red plug of the long speaker cable
into thejack labeled right rear.
Satellite Speakers
There are fouridentical satellitespeakers, two for the front and two for the rear. The front speakers
use the shortercables, and the rear speakersusethe longer cables. Connectthem as shown:
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 13

14
Input Connections
DVD in: The the DigitalTheater 6000 may be
connectedto the Dolby Digital outputfrom
any DVD player.
Note: DigitalTheater6000 cannot be connect-
ed to the AC-3 output from a laserdisc player
since a laserdisc is RF modulated.
To makethe connection,use the black digital
input cable. Plug one end into the digital
output of the DVD player and the other into
the black digital terminal on the subwoofer
back panel.
DSS in: The DigitalTheater 6000 may be con-
nectedto the DolbyDigital output from any
DSS satellite television system that provides a
digital audio output. To make this connection,
use an opticaldigital cable (not included—
for more details, contact your dealer or
Boston Acoustics directly).
Plug one end into the digital output ofthe DSS
unit and the otherinto theblack optical digital
terminal on the subwoofer back panel.
VCR and Audio in: The two stereo analog
inputs on the DigitalTheater6000 may be con-
nected to any stereo analog source. Typically
this will be a stereo TV, hi-fiVCR, or CD player.
To makethe connection,use the analog stereo
cable.Plug one end into the audio outputsof
the source unit and the otherinto theappropri-
ate terminals on the subwoofer back panel.
Make sure the correct color plug is connected
to the correct color jack: red to red and white
to white.
Source Connection
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 14

15
LED Display Panel On Center Channel Unit
1. Numerical Level Indicator
This display shows thesettingforsystem mastervolume, and the individualchannellevels (“trim
levels”) for the center speaker, surround speakers, and subwoofer. Themaster volume is numbered
between 0 and 80,thetrim levels for the center and surround speakers are between –9 and +9,and
the trim level range for the subwoofer isbetween-9 and +15. The displaydims after 5 seconds.
When DigitalTheater 6000 ismuted, the displaywillblinkcontinuously. The system canbe unmuted
by pressing the mute button, the volume up or down buttons, orany input orsystem mode button.
2. Mode Group
Dolby Digital
This LED illuminates when the user has selected either the DSS or DVD input, and thesystem’s
decoder has detected a Dolby Digital signal.
2-ch
This LED illuminates when the2-ch mode is selected. 2-channel operation may be selected at any
time, with any input. Sound will only be heard through the left and right speakers (plus subwoofer)
during 2-channel operation.
Pro Logic
ThisLED illuminates when eithertheAudio or VCRinput is selected and the5-ch mode on the
remote control is selected. This LED will also illuminate inaddition to the DolbyDigital LED when
the DigitalTheater 6000 is sent a digital signal from a DVD player, but for some reason, either the
software orthe source unit is notproperlyconfigured for 5.1 channel digital operation. See NOTE
below.
NOTE: For 5.1channel digital playback, confirm thatyoursoftwaresupports5.1 channel playback
and select “5.1” on the DVD’s maintitle screen. Also besure that your DVD player isconfigured for
DolbyDigital operation by selecting “Dolby Digital”fromyour DVD player’s set-up menu. Refer to
the instructions that came with your DVDplayer.
•
1
•
2
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 15

16
LED Display Panel On Center Channel Unit (cont.)
night
When listening at low volumes, (late at night, for example), thequietest passages can be difficult to
hearand the loud passages are oftentooloud. The night mode reduces the system’s dynamic range
(the difference between loudest and softest sounds) so the quiet parts of the program are clearly
audible even at low volume, while attenuating the loudest passages so others aren’t disturbed.
NOTE: The night mode canonly be used when Dolby Digital is active. Becauseit is software-depen-
dent, its effectcan be quite subtle, depending onthe particularprogram.
3. input Group
Audio, DSS, DVD, VCR
Input selection indicator, remains illuminated toshow source selected.
4. spkrs Group
The LEDs illuminateto show theactive speakerwhen using the testtoneand setting the trim levels.
Numeric Level Indicator
Operational Mode
Active Input
Speaker Status
•
1
•
2
•
3
•
4
•
1
•
4
•
2
•
3
•
3
•
4
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 16

17
1. Boston power Turns DigitalTheater 6000 on andoff.
2. powerTurns devices usedwithDigitalTheater 6000 on
or off. Press the button(TV, VCRor cable)for the unit
you wish to turn on or off andthen power.
3. night This button engages the system’s night mode, to
make quiet passages more intelligible at low volumes
and loudpassagesless intrusive.
4. Numeric KeypadUsedforenteringtheTV,VCR,cable
box,orDSSchannelnumberandprogrammingtheremote.
Channel and Sound Group Thesefive buttons control
the TV ,VCR, cable box, or DSS channel up or down,
sound volume of the DigitalTheater 6000 up or down,
and muting the DigitalTheater 6000.
6.
VCR Group Controls the VCR— play, pause, stop, fast
forward, rewind and record.NOTE: The recordbutton
must be pressed twice to engage the record function to
prevent accidentalrecording. The recordbutton isinop-
erative when used on a DVD player.
7. Sound Input Pressing the DVD/DSS buttontoggles
between the DVDorDSS input respectively. Pressing
the appropriate button selects the Audioor VCR input.
8.5-ch/2-ch Pressing the5-ch/2-ch button turns the sur-
rounddecoder onand off.
NOTE: For 5.1 channel digital playback, confirm that your
software supports 5.1 channel playback and select “5.1”
on the DVD’s main title screen. Also be sure that your DVD
player is configured for Dolby Digital operation by select-
ing “DolbyDigital” fromyour DVD player’sset-up menu.
Refer to the instructions that came withyour DVD player.
Whenthe5-ch/2-chbutton is pushed again, the sound
becomes 2-channel stereo (the 2-chLED will illuminate).
Sound will be heard from the left and right channels plus
subwoofer. There isno output from the center or surround
channels.
Whenthesurround decoder isengaged on stereo materi-
al by pressing the 5-ch/2-ch button,the Pro Logic LED will
illuminate. Inthis case, there is usually output from all the
speakers,even though the source material has not been
encoded in the DolbySurroundformat.(NOTE:programs
recorded in mono will appear only in thecenter channel
when surround is activated.)Many listeners enjoy the
three-dimensional effect of regular stereo material played
through the Surround decoder.
previous When using theremoteto control your
television, pressing this button reverts to the previously
viewed channel (If your televisionhas this function).
Universal Remote Control
The DigitalTheater6000comes equippedwitha universalremote controlwhich will operatemany TVs,
VCRs, cableboxes, DVDplayers, and DSS units, as wellas the DigitalTheater6000itself. Thismeans
only one remote control is needed to watch a movie, eliminating the clutter of multiple remotes.
•
1
•
1
•
2
•
2
•
3
•
3
•
4
•
4
•
5
•
5
•
6
•
6
•
7
•
7
•
8
•
8
•
9
•
9
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 17

18
1. Press the button for the unityou wish to pro-
gram—TV, VCR or cable box. The LED on the
remote will blink.
• The VCR button can also be used to pro-
gram DVD player codes, in place of the VCR.
• The cable button can also be used to pro-
gramDSS codes, inplace ofthe cable box.
3. Hold the setup button on theremote control
for about three seconds, until the LED on
the remote blinks twice.
3. Enterthe three-digit codeforyour particular
device. The LEDon the remote will blink once
afterthe firsttwonumbers are entered,and
twice after the last number isenteredtosigni-
fy it has accepted the programming. Example:
1(blink), 2(blink), 3 (blink-blink).A singlelong
blink indicatesan invalidkeysequence.
4. Test the remote control on your deviceby
pressingpower on or off.
If the remote doesnot appear to be working,
check that the right code was programmed.
Many manufacturers have multiplecodes for
differentdevices; ifthe first code doesn’t work,
try a different code. Make surethe LED on the
remote blinks every time abutton is pressed.
If not, be certain the batteriesare correctly
installed orreplacethe batteries in the remote
control.
Programming the Universal Remote Control
This universal remote is pre-programmed for hundreds of different devices.
Install the 4 “AAA” batteries in the remote.Orientthe batteries (+or -) asshown in the battery
compartment.
For your TV, VCR, cable box, DSS, or DVD player, lookup the three-digit code foryour particular
model in the included booklet.
•
1
•
2
•
3
•
4
•
1
•
2
•
3
•
4
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 18

19
You might have two devices that would becon-
trolled bythe samebutton (aVCR and a DVD,
for example,each controlled bythe VCR but-
ton, or a cable box andDSS, each controlled
by the cable button). In that case, you will have
to reassign oneof the other buttons tocontrol
that device.
Example: If you have a VCR and DVD player,
you will need to reassign the cable button to
control the DVDplayer
5. Press setup
6. Press 992 on the numeric keypad
7.Press the source button (in thisexample, the
VCR button)
8. Press thedestination button (in this example,
the cable button)
The cable button is now another VCR button,
which can be used to controla DVD player.
Program the remote as described in steps 1-4.
Button Reassignment to Control Different Devices
•
5
•
6
•
7
•
8
•
5
•
6
•
7•
8
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 19

20
Operating The DigitalTheater 6000 System
•
1
•
2
•
6
•
3
•
4
•
5
Press test tone, and the testtoneis heard
movingclockwise from speaker to speaker
at 2 second intervals. The order should be
left front, center, right front, right rear and
left rear. (No test toneis heardfrom the
subwoofer. Adjust the subwoofer level inde-
pendently of the other channels according
to personal taste or to compensate for the
effects of room placement). If the tone does
not move continuously from speaker to
speaker then oneor more speakers is not
connected to the correct output on the sub-
woofer.
As the test tone rotates around the speakers,
you may notice that some speakersarelouder
or softer than others. This is not due to any
defect, but to the differencein room acoustics
at different locations. The speaker levels
should be individually adjusted so they all
appear to have the sameloudness at the lis-
tening position.
•
1
Initial Setup – Test Tone
Before using thesystem, the relative speaker levels should becalibrated for optimum performance.
This is easily accomplished by using the system’s built-in test tone to match the levels of the front
and rear channels. The test tone button on the remotecontrol generates the test tone for calibrat-
ing the speakers.
BDT6000R (REV5).ƒ 11/22/99 5:45 PM Page 20