Botron ELITE User manual

ELITE Test Systems
01
/Quick
Start
Wiring
Botron Company Inc.

This guide shows you how to assemble and wire your ELITE Test System,
and gets you ready for everyday use. Once you have selected the perfect
place to install your test system please refer to the accompanying Quick Start
Guides; 02 Quick Start Web UI and 03 ELITE Data Systems to finish your
setup.
GETTING
TO KNOW
YOUR
ELITE
P1

P2P2

For your reference we have included an illustrated list of all components to
help aid with the installation of your ELITE Test System.
TOOLS
OF
THE
TRADE
P3

DC OUTPUT
P4

Step 1. Install 4 screws through the back of the Wall Plate and into the
ELITE Tester.
Step 2. Install 4 screws through the Wall Plate onto desired wall
location (recommended 4 feet from floor) with a clear area below for a
footplate.
MOUNT
YOUR
WALL
PLATE
P5
B
A

A
A
A
A
A
A
B
BB B
B B
P6

As you will notice, the wall plate comes with pre-cut wire channels for cable
management.
Step 1. Using the wire channels, connect the DC Output and RJ45 cable to
their respective ports on the bottom of the ELITE Tester.
Step 2. Connect the other end of RJ45 cable to the footplate.
Step 3. Grounding Your Footplate
3.1 Using the supplied Ground Cord, insert the banana plug into the
footplate.
3.2 Connect the ring terminal for the footplate ground to a known good
ground connection.
Step 4. Once you have connected your cables and wires, plug in the ELITE
Tester Power Supply (the ELITE will automatically turn on).
WIRING
YOUR
WALL
PLATE
P7

P8

The ELITE footplate comes with 4 pre-drilled holes on the underside to securely
mount the test stand pole to the footplate.
Step 1. Lay the test stand pole on its back with the footplate mounting bracket
pointing upwards.
Step 2. Mount the footplate to the test stand pole using 4 screws into the
underside of the footplate.
MOUNT
YOUR
FOOT
PLATE
P9
A

P10
AA

Once you have completed the previous section (Mount Your Footplate):
Step 1. Feed the RJ45 Cable and DC Output from the Power Supply
through the bottom rear opening of the Test Stand Pole. Pull the cables
through the pole and out the top rear opening.
Step 2. Connect the RJ45 Cable and Ground Cord to the footplate.
Step 3. Connect the ring terminal of the Ground Cord to a known good
ground.
Step 4. Connect the DC Output and RJ45 Cable into the bottom of the
ELITE tester.
Step 5. Connect the Power Supply into a 120V AC outlet.
WIRING
YOUR
FOOT
PLATE
P11

P12

Follow the diagram for the best suited network connection type.
Direct USB Connection - Firmware Updating
Connect from the ELITE using the USB cable to an available USB port on a
PC.
Direct Ethernet Connection - Data Communications
Connect from the ELITE using the Ethernet cable to an available Ethernet
port on a PC.
Ethernet Network Connection - Data Communications
Connect from the ELITE using the Ethernet cable to an available Ethernet
port on a router.
CONNECT
TO
YOUR
NETWORK
P13
A
B
C

P14
A
B
C

There are two relays, A & B, on the bottom of the ELITE Tester. Each relay
has 3 inputs; Normally Open (NO), Common (C), and Normally Closed
(NC). How you wire to your ELITE depends on the type of switch on your
external device. Once you have determined the type of switch, follow the
illustration for connection procedure.
A is triggered on an entry event (passing test result), acting as a switch to
control outside gates, such as doors, light towers, and turnstiles upon a
passing test result.
B is commonly used for exiting, when access is controlled by the ELITE
Test System. It works in conjunction with external I/O devices connected to
the tester such as ID readers and IR exit switches.
B can also be set to mirror Relay A and switch a second device upon an
entry event.
CONNECT
TO
YOUR
RELAYS
P15

P16

AN IMPORTANT NOTE
Please read this document and check that your system is set up carefully
before you first use your ELITE Test System.
LEARN MORE
You can find more information and learn even more about ELITE features at
www.botron.com/elite.
SUPPORT
Your ELITE comes with 90 days of technical support and one year of
hardware repair warranty coverage. For more information please contact:
Phone: [phone]
email: elitesuppor[email protected]
MAILING
Botron Company Inc.
21601 N. 21st Avenue
Phoenix, AZ 85027
All rights reserved. Designed by Botron.

ELITE Test Systems
02
/Quick
Start
Web UI
Botron Company Inc.

Welcome to the ELITE V2 Web UI. Here you can control the settings of your
device such as VTR (Variable Test Resistance) Technology, calibration, relays
and much more. The ELITE V2 Web UI is an interactive web app that works
in most browsers across many platforms, such as mobile phones, tablets and
desktops. This gives you access to your test equipment anywhere you go
within your network.
Once you have connected your device to your network, access the Web UI
by entering the IP address in the browser of your choice. The IP address is
automatically obtained by the ELITE V2 once connected to your network.
This Quick Start Guide is to give you an overview of the screens and features
of the Web UI.
YOUR
ELITE
V2
WEB UI
P1