Bowthorpe WMI15343 User manual

BOWTHORPE 3 DOOR 2 DRAWER ROBE
ASSEMBLY INSTRUCTIONS
Batch No.:WMI15343
Page 1of 11
Thank you for purchasing the BOWTHORPE 3 DOOR 2 DRAWER ROBE.Please read the
instructions carefully to ensure safe operation of the product.
Size: 1380 x 570 x 1888mm
Colour: LIGHT OAK
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not
destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be
kept away from young children whilst assembling your unit to avoid the danger of choking hazards.
Tools Required
4mm Allen Key x 1

BOWTHORPE 3 DOOR 2 DRAWER ROBE
ASSEMBLY INSTRUCTIONS
Batch No.:WMI15343
Page 2of 11
IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
INFORMATION
Due to the size of this product we recommend that it is assembled in the room intended for use.
When you are ready to start, make sure that you have the right tools, plenty of space and a clean, dry area for
assembly.
Unwrap all packaging materials and place the components on top of the carton box or on a clean floor to
prevent it from scratching.
Check the pack and make sure you have all the parts listed.
Ensure that this product is fully assembled as illustrated before use.
Check all screws or bolts are tightened and inspect regularly
This product should only be used on firm, level ground.
Keep small parts out of reach of children.
Make sure the legs remain in contact with the ground.
Tools are not included.
WARNINGS
DO NOT use power tools to construct this product.
DO NOT tighten screws until fully assembled.
DO NOT over tighten screws or bolts.
DO NOT use this product if parts are missing, damaged or worn.
DO NOT sit or stand on the product.
We recommend the use of the wall strap provided for safety reasons. N.B. Wall fixings are not included –
please source suitable fixings for your wall type. If in doubt please consult a qualified tradesperson. Warning:
Always ensure the area to be drilled is free from hidden electrical wires, water and gas pipes.
CARE INFORMATION
Never use scourers, abrasives or chemical cleaners.
To clean wipe with a sponge and warm soapy water. Do not use solvent based cleaners or detergents as they
can bleach or damage the product.

BOWTHORPE 3 DOOR 2 DRAWER ROBE
ASSEMBLY INSTRUCTIONS
Batch No.:WMI15343
Page 3of 11
Please check the pack contents before assembling the product. If any components are missing,
please contact your retailer. The fittings pack contains small items that should be kept away from
small children.

BOWTHORPE 3 DOOR 2 DRAWER ROBE
ASSEMBLY INSTRUCTIONS
Batch No.:WMI15343
Page 4of 11
Parts
1
2
3
BASE
1 PC
Carton No: 1 of 2
TOP FRAME
1 PC
Carton No: 1 of 2
SIDE BOARD
2 PCS(LEFT & RIGHT )
Carton No: 2 of 2
4
5
6
HANGING ROD
1 PC
Carton No: 2 of 2
BACK PANEL
1 PC
Carton No: 2 of 2
HANGING RAIL SUPPORT
1 PC
Carton No: 2 of 2
7
FRONT BOARD
1 PC
Carton No: 2 of 2

BOWTHORPE 3 DOOR 2 DRAWER ROBE
ASSEMBLY INSTRUCTIONS
Batch No.:WMI15343
Page 5of 11
CAUTION: There are many small components used in the construction of this product.
Please keep these components away from young children whilst assembling this product.
If you keep the fittings in a bowl during assembly you will be less likely to lose them!

BOWTHORPE 3 DOOR 2 DRAWER ROBE
ASSEMBLY INSTRUCTIONS
Batch No.:WMI15343
Page 6of 11
Layout Parts on Soft Surface
Lay out all parts on a soft surface i.e. Rug, Carpet or Packaging Carton to avoid damage.

BOWTHORPE 3 DOOR 2 DRAWER ROBE
ASSEMBLY INSTRUCTIONS
Batch No.:WMI15343
Page 7of 11
STEP 1
Parts Required
3. Side board x 2
7. Front board x 1
A. M6 bolt x 10
E. 4mm Allen key x 1
STEP 2
Parts Required
5. Back panel x 1
A. M6 bolt x 10
E. 4mm Allen key x 1

BOWTHORPE 3 DOOR 2 DRAWER ROBE
ASSEMBLY INSTRUCTIONS
Batch No.:WMI15343
Page 8of 11
STEP 3
Parts Required
2. Top frame x 1
A. M6 bolt x 12
E. 4mm Allen key x 1
STEP 4
Parts Required
B. M4 bolt x 6
N. Holder x 3

BOWTHORPE 3 DOOR 2 DRAWER ROBE
ASSEMBLY INSTRUCTIONS
Batch No.:WMI15343
Page 9of 11
STEP5
Parts Required
C. Screw x 5
1. Base x 1
STEP6
Parts Required
4. Hanging rod x1
6. Hanging rail
support x 1
D. Screw x 2

BOWTHORPE 3 DOOR 2 DRAWER ROBE
ASSEMBLY INSTRUCTIONS
Batch No.:WMI15343
Page 10 of 11
STEP 7
Parts Required
F. Iron Bracket x 3
D. Screw x 12
WALL STRAP
Parts Required
C. Screw x 2
D. Screw x 2
G. Bracket x 2
H. Nylon strip x 1
M. Wall plug x 2

BOWTHORPE 3 DOOR 2 DRAWER ROBE
ASSEMBLY INSTRUCTIONS
Batch No.:WMI15343
Page 11 of 11
Complete Assembly
Your BOWTHORPE 3 DOOR 2 DRAWER ROBE is now completely assembled.
Periodically check to ensure that the components are in their proper position, free from damage.
Also, make sure the connectors are tight and secure.
Keep instructions for future reference