CABINETS TO GO Findley & Myers OC3384SD User manual

Page 1
DoubleOvenCabinet 
ASSEMBLYINSTRUCTIONS
Theseassemblyinstructionsareonly applicableforallDoubleOvenCabinets.
ITEM#OC3384SD,OC3390SD,OC3396SD

Page 2
►General Instructions:
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned tofacethe
testofdailyuseandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityfor
anydamagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,
significantdamageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.
CabinetsToGowillnotbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE
PARTS IN THE QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER
CARE IMMEDIATELY AT 1-800-CABINET.
►ItemsQuantity
Item Description Qty
A Face Frame with Door 1
B Side Panels 2
C Bottom Panel 3
D Top Panel 2
E Back Panel 1
F
G
ToeKick 1
H
DrawerFront 3
I
DrawerBox 3
Hardwarebox: 1
Bumper16pcs, drawerslide3‐sets,drawerrailholder6pcs, 1"flatheadscrewsforslide18pcs
►Required tools:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
►Hardware Box:
a
b
Qty 16 Qty 9
c
d
Qty 6 Qty 6 - 3 Sets
A
A
B
Hx3
F
B
C
D
E
G
A
G
G
D
C
C
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.

Page 3
IftheOCyouareinstallingrunsthelengthofyourceilingheight,itis
recommendedtoassembletheunitstandingtoavoidscrapingyourceiling.
►Instructions:
2.
Installing the Side Panels: Insert the right and left side panels (B) into the grooves of the back panel
(D)andalign the camlockconnectors.(Figure2) Lockthe camlock witha screwdriverbyturning the screw 180°
clockwise. (Figure 3)
3. Installing the Toe Kick (F): Place the toe kick (F) at the end of side panels (B). Aligneachcamlockonthe
toekickandlockthem. (Figure 4)
4.
Install the Top & Bottom Panels (C & D)bysliding them in to the grooves.
5.
Install the face frame (A)byplacingcamlocksidedownontotheboxofthecabinet.(Figure 6) Align all
grooves and cam locks onto the face frame and coordinating cam locks. It may be necessary to open all
cabinet doors. Lock all face frame cam locks with a screwdriver. (Figure 3)
A
Figure6
Figure 2
E
B
D
Figure 4
Figure 3
F
D
C
B
Figure 5
B
C
C
Figure 1
1.
Put the Back Panel (E) face up on a flat soft working surface to ensure that the surface is not scratched
or damaged. Attach the drawer rail holders (c) to the pre-spotted areas using the supplied screws. (Figure 1)
c
Qty 6
Top
c
NOTICE

Page 4
1. Place the face frame (A) face downona flatsoftworking surfacetoensure thatthe
faceis not scratched or damaged. (Figure 1) .
2. InstalltheSidePanels(Figure2): Insertrightandleftsidepanels (B) intothegrooves of
thefaceframe (A) andalignthecamlock connectors (Figure2). Lockthe camwithascrewdriver
byturningthescrew180° clockwise (Figure4) .
3. InstalltheBottom and Microwave shelf(Figure3): Gently spreadtheside panels (B)and
insert (C) & (D) intothegroovesofsidepanels (B) untilthey areseated in theface frame (A).
4. Installing theBack PanelandToeKick (Figure5): Beforeyoustartthisstep,putthe
backpanel (E) onaflatsurfacefacingupward.Installthedrawer slide supports (f) inthepre‐
spottedareaonthebackpanel (Figure6). Thebottom of the slide supports should be facing
the bottom groove.Securethemwith2screws each (e)( Figure6).
Theninstallthe backpanel (E)
to the rearofsidepanels (B)(Figure5) .Alignandlockeachcamlock.InstalltheToeKick (F) by
lockin
► Maintenance
For daily cleaning, use a dry cloth and a soft
liquid cleaner.
Never use abrasive cleaners contai ning acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the q uality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.
G
H
6. Drawer Assembly (Figure 7): First assemble the drawer front (G) with drawer box front
(H) with screws (b). Then assemble the rest of the parts of the drawer box (H) using your
palm, or a rubber mallet if needed, to secure the dove tails into position. Repeat step for
additional drawers.
b
Qty 9
8. Install the rubber buttons (a) onto the corner of the doors where they
come in contact with the frame.
a
Qty 6-12
7. Install the drawer slides (d) into the assembled cabinet onto the drawer rail holders (c)
installed in Step 1, using the pre-drilled holes in the frame, and the provided screws. (Figure 8)
d
Qty 6 - 3 Sets
Top
dc
Figure 7
Figure 8