Box-Design Pro-Ject Pre Box DS2 Digital User manual

INSTRUCTIONS FOR USE
Pro-Ject Phono Box DS2

© Pro-Ject Audio Systems · Pro-Ject Phono Box DS2 · Revision 2017.9.06
2
Dear music lover,
thank you for purchasing a Pro-Ject Audio Systems phono amplifier.
In order to achieve maximum performance and reliability you should study these instructions for use carefully.
Warning of a hazard for the user, the unit or possible misuse.
Important notice.
Safety instructions
AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the
voltage in your area meets the voltage requirements printed on the power supply.
The power supply is used to disconnect the unit from the mains. Make sure that the power supply is easily
accessible at all times. Never handle the device, the power supply while your hands are wet or damp.
Avoid letting liquids enter the device or the power supply. Never place any item containing liquid, such
as a flower vase on or near the device. Never spill any liquid on the device or the power supply. Never
place any naked flame sources, such as lighted candles on or near the device. The product shall not be used
in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar conditions.
Connectors
Make all connections whilst the phono amplifier is disconnected from the power supply.
Take care to connect the left and right channels correctly. The right channel is usually marked red, the
left channel black or white.
Do not connect the phono amplifiers output to a phono input (sometimes labelled gram, disc or RIAA)
on the amplifier.
Never use any other power supply than the one supplied with the unit.
Connecting the record player
Connect the tonearm signal lead to the In of the phono amplifier. The grounding wire may be connected to the
screw terminal if you encounter hum problems when using the record player.
Connection to the amplifier
Connect the Out of the phono amplifier to a line input (such as AUX, CD, Tuner, Tape or Video) on your
amplifier.

© Pro-Ject Audio Systems · Pro-Ject Phono Box DS2 · Revision 2017.9.06
3
Mains power connection and methods to switch the unit on and off
Connect the low voltage plug from the power supply to the Power 18V socket of the preamplifier before
connecting the power supply to the mains. The unit can be switched on and off by using 2 different methods
which are equal in priorities.
1. Using front pushbutton to switch on or into standby
The pushbutton on the front panel of the unit alternately turns the power on or returns it to standby mode. The
blue LED on the front panel shows that the unit is powered on. If a trigger signal is present the unit can’t be
switched off by the pushbutton.
2. Remote power on - triggers
The unit can be switched on via other Box Design components when a 12V trigger voltage is present at the
2.5mm socket marked Trigger Input. Special power-on cables (polarity ) in diverse lengths are available
as accessories. The remote power-on signal can be relayed to further units via the Trigger Output socket. When
the 12V trigger signal is switched off, the unit will also switch off.
Trigger cables may only be plugged into the sockets when the unit is disconnected from the power
supply and from the mains. Failure to do so may result in damage of the unit.
Settings
The three push buttons on the left-hand side are used to set input impedance, input capacitance and input gain.
To find out which type your cartridge is please consult the literature accompanying your cartridge. The literature
for cartridges should also specify the correct input impedance (low-output MC cartridges) and the correct input
capacitance (high-output MC and MM cartridges), into which the cartridge is designed to work. If in doubt,
please consult your dealer.
Input impedance / ohms
Input capacitance / pF
Input gain / dB
pF - all LEDs off = 47pF.
LEDs pF 100, 220 and 320 - readout always + 47pF
After disconnecting the unit from the mains, all settings will be deleted.
Examples of typical settings
Ortofon Rondo Red (Low-Output MC): Input impedance 10ohms, Input capacitance - Any setting.
Input capacitance is irrelevant for low-output MC cartridges pF, Input gain 60dB
Ortofon 2M Red (MM): Input impedance 47kohms, Input capacitance 147pF, Input gain 40dB
Ortofon X5-MC (High-Output MC): Input impedance 47kohms, Input capacitance 367pF, Input gain 40dB
Subsonic
Turn on and off subsonic filter.

© Pro-Ject Audio Systems · Pro-Ject Phono Box DS2 · Revision 2017.9.06
4
Technical specifications Pro-Ject Phono Box DS2
ATypical for low output MC cartridges, Btypical for MM or high output MC cartridges
* Input capacitance is irrelevant for low-output MC cartridges
Input impedance: 10, 50, 100, 1k, 47kohms A
Input capacitance/impedance: 47pF, 147pF, 267pF and 367pF */47kohms B
Input gain: 40, 45 B / 50, 60 and 65dB A
Noise floor: 80dB (A weighted) at 40dB input gain
THD: <0,02%
RIAA-equalisation curve accuracy: 20Hz - 20kHz / max. 0,3dB
Subsonic filter: at 20Hz with 12dB/octave
Input: 1 pair RCA/phono sockets
Line-level output: 1 pair RCA/phono sockets
Outboard power supply: 18V/500mA DC, suitable for your country's mains supply
Power consumption: 100mA DC, <1W in standby
Dimensions W x H x D / weight: aluminium 206 x 71 x 194 / 1320g
wood 240 x 72 x 194 / 1770g
Potential incorrect use and fault conditions
No signal on one or both channels:
No connection between player and phono amplifier or amplifier. This could be due to a faulty plug,
broken wire or solder joint or simply loose plug/socket connection.
Strong hum:
No earth connection from cartridge or arm, or arm cable to phono amplifier, or earth loop.
Output too quiet or too loud, or distorted:
Input gain incorrectly set - input overloading or insufficiently amplified.
Service
Should you encounter a problem which you are not able to alleviate or identify, please contact your dealer for
further advice. Only if the problem cannot be resolved there, the unit should be sent to the responsible
distributor in your country.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions
for use. Modification or changes to any part of the product by unauthorized persons release the
manufacturer from any liability over and above the lawful rights of the customer.
Copyright, trademarks
Pro-Ject Audio Systems is a registered Trademark of
H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems
Copyright ©2017. All rights reserved.
The information was correct at the time of going to
press. The manufacturer reserves the right to make
changes to the technical specification without prior
notice as deemed necessary to uphold the ongoing
process of technical development.