Boyo 7" TOUCH PANEL LCD MONITOR User manual

Tnl:lnk you for purchasinq our pro(1uct
Please read this
user Manuai before
uSip£j the product. C::hange without Notice
7" TOUCH PANEL LCD MONITllR
USER MANUAL

SAFETY PRECAUTIONS
Federal Communications Commission (FCC) Statement
This Equipment has been tested and found to comply with the limits for aClass
Bdigital device, pursuant
to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference
in a
residential installation. This equipment generates, uses and
can radiate radio
frequency
energy and,
if not installed and used in accordance with the instructions, may
cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur
in aparticular installation. If this
equipment does cause harmful interference to radio or television reception,
which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures: Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on acircuit different from that
to which the receiver
is connected.
Consult the dealer or
an experienced radio ITV technidan for help.
•You are cautioned that changes or modifications not expressly approved by
the party responsible for compliance could void your authority to operate the
equipment.
This device complies with Part
15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference and,
(2) This device must accept any interference received, including interference
that may cause undesired operation
2

TABLE OF CONTENT
Safety Precaution 2
Table of Content. 3
Features 4
1. Package Contents 5
2. TFT Installation 6
3. Signal Cable Description 7
4. Control Cable Description 9
5. Front Panel Control........................................................................... 10
Main OSD Menu 11
Screen Menu , 13
Display Menu ,15
Camera Menu 16
Factory Setting Menu
18
6. Vehicle Installation 19
7. Specification " '" " '" ." 20
8.. Attachment , , , 21
3

FEATURE
•Professional Mobile Touch Panel Solution
•Advanced OSD Menu for easy use
•Support
up to 4CCD Camera inputs (Mini din connector)
•Extra
RCA input for multimedia while parking (YCD, DVD, Game device)
•Provide 2Video
11 Audio Signal Output (Live Out)
•Support Single IDual ITriple IQuad Screen (Cam Out)
•Signal Trigger for Side IRear
View
• Auto Day &Night Control via Photo Diode Sensor
•Auto Detection for
NTSC IPAL System
•
OSD Control for Individual Normal IMirror Camera Image for every camera
•Auto
power on when users are making left turn or right turn even reverse
•Able to select CAM AIB/C IR's monitoring screen
•Supported
9.6V-32V Car power system working
•Professional Metal Case with Anti Shocking Design
4

1. Package Contents
Item Qty.
1.
7" LCD Monitor
1
2. Sun-Hood
1
3. Mounting Bracket
1
4.
Accessories
1
5. Control Cable 1
6.
User Manual 1
5

I
2. TFT Installation
, ~. :
4~'1JkJ
' <<It.~~.~,¥ r(" ,
~':=-~ \J i
._-- ---_ .. _------------ --------_._--j
Step 1
Check the package and make sure all parts are included.
Step 2
Clip the sun-hood on to the monitor.
~~~~~~~+-------------------
~.
~'
; .... _~.--. -_ ....._------------------_ ..... ;
I~
,
,
,
..
~~'\~
,
,
\\~
~
r ··········· .. · .. ·fr·····=··· .. ==· .. ··~· ~· .. ··_· .. ··_· .. · .. i.
i
i~r:l;i
~ :
.. _----_._-_._- _._. --- --._-- .. _- _ _--_.;
Step 4
Install the monitor on to the bracket.
Step 5
Adjust the monitor to an appropriate Icomfortable viewing
angle before tightening the screws.
Step 6
Connect the control cable included to the power socket
which located at rear side
of monitor.
Step 7
Monitor installation is now completed. Each control cable
wire is attached with asticker to indicate its signal function.
Referred to the identification sticker for further installation.
6

3. Signal Cable Description
CAM·R
AVVIDEOIN
YS110W co-io! t:o-e
LIVE VIDEO OUT
Vtfht!& CO*Of nne
f-. .... liVEAUDIO OUT
B'OCK color ,ino-
1. CAM R(Mini din) (NTSC/PAL system presume by this car rear CCD)
For 1
51
camera connection
2. CAM A(Mini din)
For 2nd camera connection
3. CAM B(Mini din)
For 3
rd
camera connection
4. CAM C(Mini din)
For 4th camera connection
5. LIVE VIDEO OUT (White Color RCA Jack)
On screen video loop out (for recording, second monitor or other device)
6. LIVE AUDIO OUT (Black Color RCA Jack)
On screen audio loop out (for recording, second monitor or other device)
7. AV VIDEO IN (Yellow Color RCA Jack)
Connection for any Video signal (DVD, VCD, Game)
8. AV AUDIO IN (Red Color RCA Jack)
Connection for any Audio signal (such as DVD. VCD, Game)
9. CAM OUT (Green Color RCA Jack)
Video loop out (for recording, second monitor or other device)
7

Mini Din Pin Assignment
~-5
.---3
/
21
Function of the Audio
*Type 1(Standard):
1. ----- 4. GND
2. ----- 5. +12V
3. Audio 6. Video
*Type 2(Optional):
1. GND 4. +12V
2. ------ 5. -------
3. Video 6. Audio
Cam AAudio from Cam A
Cam BAudio from Cam B
CamC
Audio from Cam C
CamR Audio from Cam R
CamA+Cam BAudio from Cam A
Cam
C+Cam RAudio from Cam R
CamA+Cam RAudio from Cam R
Cam
R+ Cam BAudio from Cam R
CamA+ Cam CAudio from Cam A
Cam C+ Cam BAudio from Cam C
Cam
R/CamAB Audio from Cam R
Quad Audio from Cam R
AV Audio from AV
*Cam Out: Composite video loop out signal to recorder, monitor or other device.
*Live Video/Audio Out: On screen video/audio signal loop out to recorder, monitor
or other device.
8

4. Control cable Description
ORANGE (DIRR) 1
BLUE (REVERSE) 2
WHITE (PARK) 3
{[g]
06 BLACK(GND)
o0 5YELLOW(DIRL)
o04RED (ACC POWER)
WIRE COLOR FUNCTION REMARK
ON SCREEN VIEW
RED ACC POWER
BLACK GND
WHITE Parking Control Active GND g
:::U::JC·
BLUE Reverse Control Active Power
Level Connect to
~
Reverse Light
OI::U=-
ORANGE Right Turn Control Active Power
..................... ---.-----.
Level Connect to
c~ .. RICf,,..
Direction Light
-. :>:>o·1tr
(R)
YELLOW Left Turn Control Active Power
Level Connect to
ITJ!
Direction Light
~O-OQ·ltr...J
(L)
1. The control cable sequence: Reverse> Right I Left> Park (AV)
2. With car power is on, the monitor power js off, when making areverse Iright Ileft
turn, the monitor will display default screen.
9

5. Front Panel Control
PQWeII; Press the power button to activate the monitor or to keep the monitor
under stand by mode
(In Red L.ed).
sll.lllli With power on, press this button to select image sequence
CAM
A+B-CAM C+R-CAM A+R~CAM R+B~ CAM A+C~
CAM C+B ~CAM R+A+B-CAM A-CAM B-CAM C-
CAM R-CAM A+B .
With pull hand break, press this button to select image sequence
AV-CAM A+B-CAM C+R-CAM A+R~CAM R+B~ CAM A+C~
CAM C+B ~ CAM R+A+B--CAM A-CAM B -CAM C-CAM R-
AV .
\II.P ••••••• ···.·.·.;.; ••• ··iii·... Press this button to display defined camera input, user can select
QUAD ICAM A+B I
CAM C+R ICAM A+R~CAM R+B~
CAM A+C~CAM C+B~ CAM R+A+BI CAM AICAM BICAM CI
CAM Rvia OSD as default value.
M~Hl.I} This encoder switch provides the following function:
1. Activate OSD menu: Press the Menu switch to activate the OSD menu.
After the OSD menu
is activated, in case users does not proceed for
further set
up, the OSD menu will then automatically tum offwithin
several seconds.
2. Enter Function: Press the encoder switch to act as "Enter" function
under the OSD menu.
10

3. Volume Value: Exit the OSD menu, user can turn this switch
left or right to adjust the volume value.
*When pull the hand break, user need to press SOURCE button again
to
displayAV IN picture.
OSC MENU
1. Press the MENU button to enter to the OSD Menu
2. Turn the MENU button left or right to select the setting you
wish to proceed. The color
of the content will turns YELLOW
to identify your selection. Turn the MENU button left or right to
adjust your setting value.
3. Press the MENU button once back to submenu and then press menu
button again
in order to return to OSD menu.
Enter to Main menu:
II

Up and Down Direction buttons
Up and down arrow ofthe touch panelleD
are working as direction button. Users are able
to use them to move up and down between
each menu by click on them.
Enter button
It is working as enter functioning button of
this touch Panel. Users will able to use it to
make the selections between each menu by
click on it.
*Above direction keys are the function buttons of touch panel
Touch Panel Function for Quad or Dual screen
Under Jump key display, press the touch panel
of the position two times then it will be change to
the full screen. Press two times again it will be
returning back.
12

SCREEN Menu
The Screen menu set up contains different settinQ for the TFT:
rolBRIGHTNESS III~ 43
OCONTRAST IIII----l 32 ~
S"TURATION IIII~ BO -u
~ HUE "illli---l 50
-AUTO DAY&NIGHT ON D
~ DIR IMAGE SINGLE
REAR SETUP R
~
CD RETURN ~ \.,----J
Provide adjustment for the overall picture shade and brightness of TFT
display. Setting value from a- 100.
Provide adjustment for the contrast level
of the TFT display between the
light and dark areas. Setting value from a- 100.
Provide adjustment for the color
of TFT display between the light and
dark
area. Setting value from a- 100.
Provide adjustment for the picture TINT between light and dark area.
Setting value from a- 100.
Select "ON" to activate the auto day &night function
or "OFF" to
deactivate it.
13

"1 r'lil"'iX"?t?
IJ· .. n:·: .lYln\3~
The screen image setting of this touch panel during left Iright tum:
TRIPLE: When you are making aright tum or left turn, the screen of
touch panel will display triple images for left hand side, right
hand side and rear view when you are making aright turn
or left tum.
DUAL: With proper wiring, the screen will display dual image for
both rear and right hand side view when making aright turn.
While left turning, the screen will show dual image for both
rear and left hand side view.
SINGLE: Screen
of touch panel shows only single picture on direction
tum. The screen will show only left side view on left tum and
only right side view on right tum.
The screen image setting
of this touch panel during reverse gear:
R:
R+A:
R+B:
R+A+B
Screen will display single image for Cam Ronly.
Screen will display dual image for both Cam Rand Cam
A.
Screen will display dual image for both Cam Rand Cam B.
Screen will display triple image from Cam R ' Cam A ' Cam B.
Return to OSD menu selection screen.
14

DISPLAY MENU
The DISPLAY MENU set up contains the on screen identification
and the activation
of the distance gauge.
Display ON
Display Gauge ON
OSDlock ON
Rerurn •
1111.1
Set "ON" to show the source of video input on screen or "OFF" to keep it
invisible.
mlli811111111
Set the distance gauge "ON" to show the distance gauge on screen while
reserving
or "OFF" to de-activate the distance gauge.
(This "DISTANCE GAUGE" is for user's reference only)
G1)IDI;trlll
This function provides protection when an unauthorized person tries to
access the OSD settings to release key lock function press JUMP key
and Source for over 5sec.
ffRuRf4
Return to OSD menu selection screen.
15

(mD] CAMERA MENU
MIRROR ~
JUMP QUAD
CAM our QUAD
RETURN ~
Select "ON" to activate the mirror function for different cameras or
"OFF" for anormal image.CAM A"OFF"
CAM B"OFF"
CAM C"OFF"
CAM R"ON"
IIMI By pressing this button, the driver will be able to obtaine the image
selected under this setting.
QUAD Obtain image from all camera input in quad
picture while pressing the JUMP button and press source
key to returning back to the last screen.
CAM
A+B Obtain image from camera A+B in dual picture
while pressing the JUMP button and press again
to returning back to the last screen.
CAM C+R Obtain image from camera C+R in dual picture
while pressing the JUMP button and press source key
to
returning back to the last screen.
CAM A+R Obtain image from camera A+R in dual picture
While pressing the JUMP button and press
source key to returning back to the last screen.
16

CAM R+B Obtain image from camera R+B in dual picture while
pressing the JUMP button and press source key
to
returning back to the last screen.
CAM A+C Obtain image from camera A+C
in dual picture while
pressing the JUMP button and press source key
to
returning back to the last screen.
CAM C+B Obtain image from camera C+B
in dual picture while
pressing the JUMP button and press source key
to
returning back to the last screen.
CAM R+A+B Obtain image from camera R+A+B
in triple picture
while pressing the JUMP button and press source
key to returning back
to the last screen.
CAM AObtain image from camera Awhile pressing the
JUMP button and press source key to returning back
to the last screen.
CAM BObtain image from camera Bwhile pressing the
JUMP button and press source key to returning back
to the last screen.
CAM CObtain image from camera Cwhile pressing the
JUMP button and press source key to returning back
to the last screen.
CAM RObtain image from camera Rwhile pressing the
JUMP button
and press source key to returning back
to the last screen.
1.·i~f£I]f
Composite video loop out to recorder, monitor or otherdevice
QUAD Recording or viewing from the output device
in quad
mode
CAM ARecording or viewing from the output device for CAM
Aimage
CAM BRecording or viewing from the output device for CAM
Bimage
CAM CRecording or viewing from the output device for CAM
Cimage
CAM RRecording or viewing from the output device for CAM
Rimage
RETURN Return to OSD menu selection screen.
17

Factory Setting Menu
Recall ~
Time OiJ! Set 10
Exit ...
J'Jmp SOl:lce r:'owe'"
@ c::::::I c::::::I c::::::I 0
RECALL: Use this feature to recall the factory default settings.
Time Out: When splite screen under Jump mode settingIthe time back
to
splite screen after touched for desired camera screen
Setting value from 0 - 100.
EXIT: Use this feature to exit OSD menu.
18

6. Vehicle Installation
;' "
I. _. .._ .. . , Green
;' "
;' "Vellow
/, .. -- _._ "
;' 1M ';100
;' --------------,
I;' ,
I
(This" DISTANCE GAUGE" is for user's reference only)
a. Install Camera R(for rear view)
b. Use ameasuring tool to mark out the distance behind the vehicle.
c. Adjust the viewing angle of the camera so that the distance gauge shown
from the TFT match to the distance marks behind the vehicle.
Switch to Rear view with source button, the screen always display
on 16:9
While rear viewing, the screen always display
on 4:3 to correct size percentage
SOURCE button: Rear viewing:
16 9
~iVEAYDIOOUT Q' 0,
Klock nne P ,
L1VEVIDEOOUT ;
While line' ."c
ll
K~®O~
DVRorVCD
I";~- ~
4tE
iibli)I0
=~
CAM.o.
CAMOlJr
Green line
CAMe
AVAUDIOIN
Red line
AVVIDEO IN
Yellow nne
~rth
~~
~_-+CA=M;.;"R --- ... :Jl'
..... -----REVERSE -Blue Line
t------llEFT -Yellow line
t------.power - Red line
..... -----~ARK -White line
..... -----GND - Blacl< line
I-------RIGHT -Orange line
19

7. Specification
Screen size 7Inch Touch Panel (diagonal)
Active area 154.08(H) x
86.58M
Pixel confiQuration 0.107 x0.370
Resolution 1440(W) x234 (H)
ViewinQ
anQle UP:40° /Down:60° /Left: 60° /RiQht:60°
Power source: DC9.6V
-DC32V
Contrast ratio 300:1 •
BriQhtness 400 cd/m2•
Composite Video In
Connector RCA
Input
SiQnal
1Vpp
Impedance 75 Ohms
Camera MINI DIN In
Connector 6PIN MINI DIN (Standard)
Input video signal level 1Vpp
Impedance 75 Ohms
Input audio signal level 1Vpp
Power output for camera
DC12V350mA
AVAUDIO IN
Connector RCA
Input video siQnallevel 1Vpp
Impedance 75 Ohms
Composite Video Live Out
Connector RCA
Input signal level 1Vpp
Impedance 75 Ohms
CAM OUT
Connector RCA
Input siQnallevel 1Vpp
Impedance 75 Ohms
Audio LIVE OUT
Connector RCA
Input signal level 1Vpp
Impedance 75 Ohms
Dimension
WxHxD:
192 x140.5 x51.8mm
Weight N.W.lGW.: 2kg/2.28kg
Environmental:
Operation temperature -10°C-70°C
Storage temperature -30°C-80°C
Humidity 20%-80%
.The brightness and contrast ratio specifications are from panel specification.
Design and Specifications are
subject to change without notice. V1.42
20