B+B SmartWorx FOSTCDRi-PH-MT Operating and maintenance instructions

Recommended Accessories
Industrial Power Supply
Model# MDR-20-24
Document Number: 710-10863-00_r2_FOSTCDRI-PH-xx_2118qsg
1 [phone] | Europe: [phone]
www.advantech-bb.com
707 Dayton Road | PO Box 1040 | Ottawa, IL 61350
Phone: [phone] | Fax: [phone]
www.advantech-bb.com | E-mail: [e-mail]
Before you begin, be
sure you have the following:
Models FOSTCDRi-PH-MC,
FOSTCDRi-PH-MT,
FOSTCDRi-PH-SC
3-Way Isolated Serial to Fiber Optic Converter
Fast and easy on the web: www.advantech-bb.com
+ FOSTCDRi-PH-xx Fiber Optic Converter
+ Required but not included:
+10 to 48 VDC Power Supply
QUICK START
GUIDE
SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B,
C AND D HAZARDOUS LOCATIONS, OR NONHAZARDOUS
LOCATIONS ONLY.
CONVENANT À L’EMPLOI DANS LES SITES DANGEREUX
DE CLASSE I, DIVISION 2, GROUPES A, B, C ET D, OU
DANS LES SITES NON HASARDEUX SEULEMENT.
WARNING - EXPLOSION HAZARD - SUBSTITUTION OF
ANY COMPONENT MAY IMPAIR SUITABILITY FOR CLASS I,
DIVISION 2.
ATTENTION - DANGER D’EXPLOSION - LA SUBSTITUTION
DE COMPOSANTS PEUT ENTRAÎNER UNE ADÉQUATION À
LA CLASSE I, DIVISION 2.
WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT
EQUIPMENT WHILE THE CIRCUIT IS LIVE OR UNLESS
THE AREA IS KNOW TO BE FREE OF IGNITABLE
CONCENTRATIONS.
ATTENTION - DANGER D’EXPLOSION - LA SUBSTITUTION
DE COMPOSANTS PEUT ENTRAÎNER UNE ADÉQUATION À
LA CLASSE I, DIVISION 2.
Field wiring connections must be made using 105 °C minimum
copper supply wires.
Les connexions de câblage sur site doivent être réalisées en
utilisant des câbles d’alimentation en cuivre de 105 °C minimum.
To be installed in accordance with control drawing 8510r001.
Pour être installé conformément au dessin de contrôle 8510r001.
Multi-drop Ring
Model Number Connector Fiber Type Range Size
FOSTCDRi-PH-MT ST MM 2 kM 62.5/125 µm
FOSTCDRi-PH-MC SC MM 2 kM 62.5/125 µm
FOSTCDRi-PH-SC SC SM 15 kM 9/125 µm
Wavelength = 1310 nM
UL Class 1 Div. 2 Information
5

A) Power LED
B) Data LEDs
C) Fiber Optic ports
D) Serial TB
E) Ground Lug
F) DIP Switch
G) Serial Mode Switch
H) Power TB
Product Overview
Conguration DIP Switch
Fiber Optic Connections
Power & Ground Connection
Wiring Examples
1
4
2
3
Terminal RS-485 2-Wire RD422/485 4-Wire
A--- TDA (-)
B--- TDB (+)
CDATA A (-) RDA (-)
DDATA B (+) RDB (+)
EGround Ground
Built-in Termination Resistor 5
Use the 120Ω Built-in Termination ON
Use External or No Termination OFF
Built-in Trasmit Bias Resistor 6
Use the External or No Bias Resistor ON
Use the 1.2KΩ Transmit Bias Resistor OFF
Built-in Receive Bias Resistor 7
Use the External or No Bias Resistor ON
Use the 1.2KΩ Receive Bias Resistor OFF
Fiber Optic Mode 8
Multi-drop Ring ON
Point-to-point OFF
1 2 3 4
RS-485 2-Wire
Half Duplex ON ON ON ON
RS-485 4-Wire
Full Duplex ON OFF OFF OFF
RS-422 Full
Duplex OFF OFF OFF OFF
Terminal Signal Direction
ARD Output
B--- ---
CTD Input
D--- ---
EGround ---
For an explanation of RS-485 termination requirements,
more documentation can be found at advantech-bb.com
+
2-Wire RS-485
RS-422/ 4-Wire RS-485
RS-232
Point-to-Point
Positions 5, 6, 7 are used for termination and biasing. Position 8 is
used for ber optic point-to-point or multi-drop ring.
Position 1 = ON for RS-485, OFF for RS-422. Positions 5, 6, 7
are used for termination and biasing. Position 8 is used for ber
optic point-to-point or multi-drop ring
DIP Switch positions 1 through
7 have no effect in RS-232
mode. Set position 8 to OFF
for ber optic point-to-point or
multi-drop ring.
Set DIP Switch position 8 to OFF on both converters. Connect
Fiber Optic TD to Fiber Optic RD and vice versa.
E = Ground
Note: Your FOSTCDRi-PH-x converter can only connect to
another FOSTCDRi-PH-x converter model at the other end of
the ber optic cable.
+