Brähler Systems CMic Slim UTM User manual

Quick Guide
DIGIMIC CMic Slim UTM
Under table solution for microphone unit CMic
Article no.: 05. 090

DIGIMIC CMic Slim UTM Quick Guide
Quick GuideQuick Guide
Quick Guide
2
BRÄHLER Systems GmbH
Auf der Alten Burg 6
53639 Königswinter
Germany
T
+4
9 (0)
224
4
930
-
0
F [phone] [e-mail]
www.braehler-systems.com
05. 090 QG 200 3 V .0 BRÄHLER Systems is committed to continually improving its products and so reserves the right to make technical modifications without notice.
Introduction and connectors
Introduction and connectorsIntroduction and connectors
Introduction and connectors
A microphone unit mounted almost invisibly. This is exactly what the CMic Slim UTM from Brähler Systems
offers you. The microphone unit is mounted under the table in simple aluminium housing - only what is really
needed is visible: Microphone jack and button. This can be integrated into existing surfaces or control panels
according to your wishes. All UTM versions are available in both 8-channel and 32-channel versions.
The CMic Slim UTM is not allowed to be connected in a chain with DIGIMIC interpreter units.
XLR connector for microphone
PREV: Connection from previous
unit
or
central unit (RJ45 connector)
NEXT: Connection to the next unit
(RJ45 plug)
Connection for
microphone button
Example system picture
(32 channel version)

DIGIMIC CMic Slim UTM Quick Guide
Quick GuideQuick Guide
Quick Guide
3
BRÄHLER Systems GmbH
Auf der Alten Burg 6
53639 Königswinter
Germany
T
+4
9 (0)
224
4
930
-
0
F [phone] [e-mail]
www.braehler-systems.com
05. 090 QG 200 3 V .0 BRÄHLER Systems is committed to continually improving its products and so reserves the right to make technical modifications without notice.
Operating
OperatingOperating
Operating
The CMic Slim UTM is designed for installation in the smallest of places - for example under the table. Please
refer to the following drawings for the required space. (Please note that you also need space for cables and
plugs).
Befestigen Sie die DLine Slim UTM an ihrem Bestimmungsort.
Drill holes in the destination of your microphone and microphone button. Fasten the appropriate modules
(button and socket) in the drill holes (for drill sizes, please refer to the corresponding module). Attach the CMic
Slim UTM to its destination (drill holes specified, see pictures above).

DIGIMIC CMic Slim UTM Quick Guide
Quick GuideQuick Guide
Quick Guide
4
BRÄHLER Systems GmbH
Auf der Alten Burg 6
53639 Königswinter
Germany
T
+4
9 (0)
224
4
930
-
0
F [phone] [e-mail]
www.braehler-systems.com
05. 090 QG 200 3 V .0 BRÄHLER Systems is committed to continually improving its products and so reserves the right to make technical modifications without notice.
Now first connect CMic Slim UTM and microphone button and socket. Only use suitable cables.
You then establish a connection between your CMic Slim UTM and your DIGIMIC system. Connect the CMic
Slim UTM with your central unit or a previous unit (PREV, RJ45 plug) and the following units (NEXT, RJ45 plug).
The CMic Slim UTM is immediately ready for use.
Connection from the
central unit or from the
previous unit
Connection to the
next unit

DIGIMIC CMic Slim UTM Quick Guide
Quick GuideQuick Guide
Quick Guide
5
BRÄHLER Systems GmbH
Auf der Alten Burg 6
53639 Königswinter
Germany
T
+4
9 (0)
224
4
930
-
0
F [phone] [e-mail]
www.braehler-systems.com
05. 090 QG 200 3 V .0 BRÄHLER Systems is committed to continually improving its products and so reserves the right to make technical modifications without notice.
Chairman Version
The CMic Slim UTM is also available in a Chairman version. It gives special priority to the chairman of a
conference. Press the Override button to mute all delegate units. Two variants can be set on the Central Unit:
Permanent:
Permanent:Permanent:
Permanent: Press the Override button to mute all delegate units. Delegates must turn on their microphones
again to speak.
Temporary:
Temporary:Temporary:
Temporary: Pressing and holding the override button mutes the delegate units. When you release the Override
button, the previously muted delegate units are turned on again.
For the Chairman version of the CMic Slim UTM you need a corresponding "Chairman Microphone
Button" module.
Connector assignment
The CMic Slim UTM has the following connector assignment as standard:
Tiny XLR
Tiny XLR Tiny XLR
Tiny XLR 4
44
4-
--
-pin (Mic and MUTE buttons)
pin (Mic and MUTE buttons)pin (Mic and MUTE buttons)
pin (Mic and MUTE buttons)
GND
2MUTE button (only by Chair Version)
3MIC LED
4MIC button
XLR 5
XLR 5XLR 5
XLR 5-
--
-pin
pinpin
pin (
((
(conference microphone
conference microphoneconference microphone
conference microphone)
))
)
Cable Shield
2Illuminated ring (+)
3Mic. Signal (unbal.)
4Illuminated ring (-)
5Mic. supply (5V)
Warnings
The connectors of the DIGIMIC CMic Slim UTM are only suitable for devices of the DIGIMIC
family. Do not connect any other devices!
In case of faults contact a technician, do not try to repair, screw on or similar the CMic Slim UTM
by yourself.

DIGIMIC CMic Slim UTM Quick Guide
Quick GuideQuick Guide
Quick Guide
6
BRÄHLER Systems GmbH
Auf der Alten Burg 6
53639 Königswinter
Germany
T
+4
9 (0)
224
4
930
-
0
F [phone] [e-mail]
www.braehler-systems.com
05. 090 QG 200 3 V .0 BRÄHLER Systems is committed to continually improving its products and so reserves the right to make technical modifications without notice.
Further information about our products can be found on the Internet under:
www.braehler-systems.com
© 20 9
Copyright by BRÄHLER Systems GmbH, Königswinter
All rights reserved, in particular (also in extracts) those of translation, reprinting, reproduction by copying or
similar procedures.
BRÄHLER Systems reserves the right to make technical changes without prior notice.
Brähler Systems GmbH
Auf der Alten Burg 6
53639 Königswinter, Germany
T [phone]
F [phone]
[e-mail]