Bradley 7910 User manual

215-1699 Rev. B EN 10-07-009
© 2011 Bradley Corporation
Page 1 of 3 1/26/2011
P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 800.BRADLEY (800.272.3539) FAX [phone]
bradleycorp.com
Installation
IMPORTANT!
Read this entire installation manual to ensure proper installation. When
finished with the installation, file this manual with the owner or maintenance
department. Compliance and conformity to local codes and ordinances is
the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for
before discarding packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Make sure that all water supply lines have been flushed and then completely
turned off before beginning installation. Debris in supply lines can cause
valves to malfunction.
Product warranties may be found under “Products” on our web site at
bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
•
•
•
•
Single Valve
Recessed Hose Box
Model 7910
Supplies Required ................................................. 2
Installation ............................................................. 2
Optional Left Supply Configuration........................ 3
Right Supply Configuration Shown

7910 Single Valve Recessed Hose Box Installation
21/26/2011 Bradley Corporation • 215-1699 Rev. B; EN 10-07-009
Supplies Required:
• Hardware for anchoring the Hose Box to framing or wall studs
• 1/2" NPT supply connection
• For optional left side supply: Teflon plumber's tape or Perma-Lok (or equivalent)
Tools Required:
• Security Allen Wrench (provided)
• Flat head Screwdriver
• Small crescent wrench
Rough-In Dimensions
8-5/8" (219) x 8-5/8" (219) wall opening
Top View
Front View Side View
8-5/8"
(219)
8-5/8"
(219)
12-5/8"
(321)
10"
(254)
10"
(254)
5-7/8"
(147)
1"
(25)
4"
(102)
1-7/8"
(48)
(mm)
Security
Allen Wrench
(provided)
1Mount Box in Wall
ARemove door assembly
prior to mounting.
BMount box so front edge will be
flush with FINISHED wall.
Rough in support frame and mount
box before attaching drywall or other
wall coverings.
Unit is fully assembled at factory for right side supply. For left side supply option,
refer to instructions on page 3 before mounting unit in wall.

Installation 7910 Single Valve Recessed Hose Box
Bradley Corporation • 215-1699 Rev. B; EN 10-07-009 1/26/2011 3
2Connect Supply
Optional Left Supply Configuration
AConnect 1/2"NPT supply.
(Side connection shown.)
CActivate supply and test for leaks.
Adjust stop point if necessary.
Re-attach door.
BTighten vacuum breaker onto hose
bibb and secure by tightening screw.
ARemove door. After carefully noting
configuration of fittings, remove
vacuum breaker from hose bibb.
BRemove stand-off bracket, hose bibb and other
components from inner box. Disassemble fittings.
CRotate cabinet 180˚ so outlet holes are on the left. Re-install
valve and stand-off bracket, being careful to align screwdriver
stop with stop hole in cabinet. Proceed to Step 1 on page 2.
Left supply configuration is the opposite of standard right supply configuration.
Thoroughly clean threads and seal with plumber's
tape or Perma-Lok (or equivalent).
Vacuum breaker's break-away screw (or
set screw) is not tightened at factory.
Stand-Off
Bracket
Hose Bibb
Vacuum
Breaker
Screwdriver
Stop
Screwdriver
Stop Hole
Outlet
Holes
Elbow (remove for top
connection)