JADO Wynd 816/348 Series User manual

Installation Instructions
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
©JADO USA 2003
Products Luxury Faucets and Accessories
Three Hole Bidet Set
with Vacuum Breaker
8TEST INSTALLED FITTING AND
CONNECTIONS FOR LEAKS
With FAUCET HANDLES in OFF position, turn on
WATER SUPPL ES (1) and check all connections
for leaks.
Operate both handles to flush water lines thoroughly.
Turn diverter to rim wash and bidet spray.
Operate L FT ROD (2) and fill bidet with water. DRA N
STOPPER (3) should make a good seal and retain water
in bidet. Adjust stopper height if required by repositioning
L FT ROD (2) and tightening SET SCREW (4).
Release DRA N STOPPER (3) and check all drain
connections and "P" trap for leaks. Tighten if
necessary.
9HELPFUL HINTS FOR CLEANING AND MAINTENANCE
The solid brass product you have just purchased has been designed to give you years of beauty and service. It is
important to bring to your attention proper care and maintenance procedures, which will ensure its lasting beauty.
NOTE Diverter valve is not a positive shut-off to rim wash.
First and foremost, it is important (as it is with any fine piece of jewelry or furniture) that the product be wiped clean and
dry with a soft damp cloth after every use.
Second, under no circumstances should an abrasive cleaner or combination cleaner/polish be used on JADO products.
The abrasive nature of such products will eventually destroy the finish and void the warranty.
n the event of stubborn blemishes shown on the finish, we recommend use of Windex window cleaner with a soft cloth,
but we do not recommend it be used on an everyday basis.
t is important to note that it is normal to expect signs of usage over time.
Thank you for sele ting JADO for your home.
109150
109150
JADO
JADO
1
1
2
3
4
JADO USA
7845 East Paradise Lane
Scottsdale, AZ 8526O
Phone:(8OO) 227-2734
Fax: (8OO) 552-JADO(5236)
www.jadousa.com
Product Number
Bidet
816/348/...
Wynd 816
TO THE PURCHASER OF JADO BRASS PRODUCTS
Attention installer:
Please leave This Pamphlet for The Owner
POLISHED BRASS AND CUSTOM FINISHWARRANTY: A 1YEAR LIMITED FINISH WARRANTY from date of purchase is provided to the
first residential owner against defects in materials and workmanship. Due to the ever-changing finish of Patina products, the finish warranty
is excluded. Warranty shall not include problems related to the installation of the product.
MECHANICS
MECHANICAL WARRANTY: A LIFETIME LIMITED WARRANTY is provided to the first residential owner on parts to be free from failure
related to defects in materials and workmanship but not installation.
CONDITIONSTOWARRANTIES
JADO Bathroom & Hardware Manufacturing Corp.places the following conditions on its finish and mechanical warranties to the first residential owner only.
JADO finish and mechanical warranties are limited to products correctly installed and used in a residential environment.
JADO warranties exclude General Finishes, Polished Brass and Custom Finishes exposed to marine environment and direct exposure to sunlight.
JADO warranties will not assume liability for damage due to abuse, mishandling, incorrect installation, improper maintenance, or deterioration
due to normal use.
JADO will not be liable for labor or other costs relating to the sale, installation, or replacement of their products.
In the event of a defect in any JADO product covered by this warranty, the product must be returned to the dealer where originally purchased
along with proof of purchase.
JADO's obligation under the warranty shall be limited to the repair or exchange of any product which has been determined by JADO to be
defective after appropriate examination.
The state of California has mandated under Proposition #65 that
manufactures of products, including faucets which come into
contact with potable water, must warn the consumer if the product
contains materials listed by the state as a carcinogen or
reproductive toxin. Lead, which is contained in all brass faucets in
limited amounts appears on the State's list.
Preliminary industry tests have indicated that users of faucets
made from brass face no significant danger, however,
California Proposition #65 requires that we provide you with the
following notice:
NOTICE: JADO products conform to industry
requirements of water conservation under the
ASTM / ANSI A112.18.1M-1994 plumbing code.
Lavatory, bidet, wet bar and kitchen faucet sets
have a maximum flow rate of 2.2GPM. Shower
heads, hand showers and body sprays have a
maximum flow rate of 2.5GPM.
Warning: This product contains an element
known to the State of California to cause cancer
of reproductive harm.
JADO BATHROOM AND HARDWARE MFG.CORP.
7845 East Paradise Lane
Scottsdale, AZ 85260
JADO warrants this product to be free from defects in materials or workmanship for as long as the original consumer purchaser
owns their home.
JADO will provide, free of charge, at it’s sole option, replacement part(s) or product (or if no longer available, a comparable
product) to replace those which have proven defective in materials or workmanship.
Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to JADO for all limited
warranty claims.This limited warranty is non transferable.It does not apply in the event of product damage due to the use of other than
genuine JADO replacement parts, installation error, abuse, misuse, or improper care and maintenance (whether performed by
a plumber, contractor, service provider or member of the purchaser’s household).The limited warranty excludes damage due to aggressive
air or water conditions, or harsh or abrasive cleaners and/or materials.This limited warranty excludes all industrial, commercial and business
usage, whose purchasers are hereby extended a two year limited warranty (with the exception of solenoid valves and other electronic
components which carry a one year limited warranty) applying to all other terms of this limited warranty except duration. This limited warranty
does not cover labor charges incurred and/or damages sustained in installation, repair or replacement, nor incidental or consequential
damages, all of which are expressly disclaimed.This limited warranty is applicable only to JADO faucets manufactured after June 1, 1996
and installed in the United States and/or Canada.
This limited warranty gives the original consumer purchaser of an JADO faucet specific legal rights which may vary from state to
state or from province to province.This limited warranty does not cover any liability for consequential or incidental damages, all of which
are hereby expressly disclaimed, or the extension beyond the duration of this limited warranty of any implied limited warranties, including
those of merchantability or fitness for an intended purpose.In some states or provinces the exclusion or limitation of incidental or consequential
damages is not allowed, so those exclusions may not apply to you.
JADO Bathroom & Hardware Manufacturing Corp. provides the following warranties only to the first residential owner of our products.
FINISHES
FAUCET LIFETIME FUNCTION AND FINISH LIMITED WARRANTY

ROUGHING-IN
DIMENSIONS
SMALL
END
LARGE
END
LARGE
END
VALVE
OUTLET
VALVE
OUTLET
PUTTY
1
2
3
3
2
4
1109150 109150
3
B DET
LEDGE
2-1/2" - 6" 2-1/2" - 6"
1-1/4"
MAX 4"
1-1/16" D.
MAX 7"
MAX 2"
11" 2-1/8" D.
SPRAY
1-1/8 D.
MAX 13"
D VERTER
AND VACUUM
BREAKER
L FT ROD
CONNECT ONS ARE FOR1/2" PS
FLEX BLE SUPPL ES or 3/8" O.D.
BULL-NOSE R SERS
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter Regular Screwdriver
Basin Wrench
3
5
6
INSTALL SUPPLY HOSES
INSTALL SPRAY BODY
INSTALL HANDLES
Connect small end of SUPPLY HOSES (1) TO "Y" ADAPTER (2)
and larger end to each VALVE OUTLET.
Important Loop SUPPLY HOSES (1) as illustrated
so they do not kink.
Connect one end of SPRAY HOSE (7) to HOSE ADAPTER (8)
and the other end to shank of SPRAY BODY (3). Tighten hose
connections to make a water tight seal.
2
4
1
3
5
6
9
7
8
Hex wench, supplied
B DET
MOUNT NG
SURFACE
For Diverter handle nstall D VERTER
HANDLE (5) onto VALVE STEM (6) of
D VERTER (9). Secure D VERTER
HANDLE (5) with SCREW (7). Thread
HANDLE CAP (8) onto D VERTER
HANDLE (5).
For Lever Handles nstall FR CT ON
WASHER (1) onto base of LEVER
HANDLE (2). Turn VALVE to off
position and align LEVER HANDLE (2)
as shown. nstall LEVER HANDLE
(2) onto VALVE STEM (3) and tighten
SET SCREW (4) with HEX WRENCH
supplied.
JADO
JADO
1
Apply putty to the underside of SPRAY BODY
FLANGE (3) and install SPRAY BODY (3) into
spray hole of Bidet.
From underside of Bidet install RUBBER WASHER (4),
F BER WASHER (5) and LOCKNUT (6) onto shank of SPRAY
BODY (3). Tighten LOCKNUT (6) to make water tight seal.
4
8
5
67
7
Connect water supplies to FAUCET (1) with
1/2" PS FLEX BLE SUPPL ES (2) or 3/8"
O.D. BULL-NOSE R SERS (3). Use adjustable
wrench to tighten connections. Do not over
tighten. Be careful not to kink copper supply
when bending. Use tubing cutter to cut to
proper length.
Supply connections are made after bidet
has bee installed.
3
2
HOT
HOT
COLD
FRONT
COLD
FERRULE
COUPL NG
NUT
1
NOTE: FLEXIBLE SUPPLIES ARE NOT INCLUDED
AND HAVE TO BE PURCHASED SEPARATELY.
B DET
MOUNT NG
SURFACE
Remove L FT ROD NUT (1), METAL WASHER (2) and
RUBBER SEAL WASHER (3) from L FT ROD GU DE (4).
Drop L FT ROD GU DE (4) into rear hole of bidet.
From below install RUBBER SEAL WASHER (3), METAL
WASHER (2) and secure guide assembly with L FT ROD NUT (1).
LIFT ROD GUIDE INSTALLATION
WATER SUPPLY CONNECTIONS
2-7/16" D. 3"
2-7/16" D.
APPLY SEALANT
OR TEFLON TAPE
4
A FOAM SEAL (1) is installed on underside of FLANGE (2). (Plumbers
Putty may be used in place of FOAM SEAL (1) if desired.)
Apply sealant or Teflon tape to threads of TA LP ECE (10) and
thread into DRA N BODY (7) making a water tight seal.
Drop FLANGE (2) into LAVATORY DRA N (3). From below assemble
RUBBER GASKET (4), PLAST C WASHER (5) and LOCK NUT (6) onto
DRA N FLANGE (2). Do not tighten fully.
INSTALL POP-UP DRAIN
FIG. 4a
FIG. 4b
FIG. 4
FIG. 4
FIG. 4a
FIG. 4b
1
4
3
2
5
6
7
8
6
9
2
Adjust STOPPER (13) height by repositioning POP-UP ROD (16) in SW VEL (15)
and tightening SET SCREW (18).
Assemble POP-UP SW VEL (15) to P VOT ROD (11) but do not tighten.
Drop POP-UP ROD (16) through other hole in POP-UP SW VEL (15) and
tighten SET SCREW (17)
Assemble P VOT ROD (11), and P VOT NUT (12) as shown. nstall CONCAVE
WASHER (19) into P VOT ROD OPEN NG (9) if not preinstalled. Hand tighten
P VOT NUT (12). Drop STOPPER (13) into drain.
(
To vandal proof drain rotate STOPPER (13) so PIVOT ROD (11) goes
through EYE (14) of STOPPER (13) . Make connection to "P" TRAP.
nspect inside DRA N BODY (7) that SEAL (8) is installed. Thread
DRA N BODY (7) tight against FLANGE (2) to make a water tight seal.
10
9
7
6
12
19
16
1517
18
2
10
14
13
11
The P VOT ROD OPEN NG (9) in DRA N BODY (7) should face the rear
of the lavatory. Tighten LOCK NUT (6) on FLANGE (2) to make a water
tight connection with channel locks. Do not over tighten.
1-1/4" O.D.
JADO
JADO
1Turn off hot and old water
supplies before beginning.
CAUTION
2
FRONT
4
1
5
19
18
17
10
13
6
7
8
9
14
15
16
11
12
INSTALL TRANSFER VALVE
2INSTALL CONTROL VALVES
Apply sealant or Teflon tape to threads of SPRAY ELL (1) and
install into TRANSFER VALVE (2). Note Arrow on SPRAY
ELL (1) points down, see illustration.
nstall "Y" HOSE ADAPTER (3) with SEAL (4) to bottom nipple of
TRANSFER VALVE (2) and tighten to make a water tight seal.
nstall LOWER CONE SEAL (5) onto TRANSFER VALVE (2) and
insert TRANSFER VALVE (2) from under side of Bidet into the
center forward hole.
nstall UPPER CONE SEAL (6), FR CT ON WASHER (7) and
MOUNT NG NUT (8) onto TRANSFER VALVE (2).
Tighten MOUNT NG NUT (8) to secure the TRANSFER VALVE (2)
and make a water tight seal.
Thread TRANSFER VALVE ESCUTCHEON (9) onto MOUNT NG
NUT (8) until snug against bidet ledge.
COLD
HOT
B DET
LEDGE
APPLY SEALANT
OR TEFLON TAPE
10˚ 10˚
The HANDLES and HANDLE BASES are installed on VALVE BOD ES (10) and
must be removed to install VALVE BOD ES (10) from under bidet mounting surface.
To remove LEVER HANDLES (11); loosen SET SCREW (12) with Hex Wrench
supplied with faucet. Pull LEVER HANDLE (11) off and unthread HANDLE BASE (13)
from VALVE BODY (10). Remove ESCUTCHEON (14). Unthread MOUNT NG R NG
(15) and remove STOP WASHER (16).
nstall STOP WASHER (16) onto VALVE BODY (10). Thread MOUNT NG R NG (15) snug against STOP WASHER (16). Place
ESCUTCHEON (14) onto MOUNT NG R NG (15). Thread HANDLE BASE (13) until snug against ESCUTCHEON (14). Set
VALVE BOD ES (3) so that their outlets are facing toward TRANSFER VALVE (2) and then tighten LOCKNUT (17) using wrench.
Thread LOCKNUT (17) to bottom of VALVE BODY (10). Make sure F BER
WASHER (18) and RUBBER WASHER (19) are installed. nsert VALVE BODY (10)
through mounting hole from underside of bidet mounting surface.
Note VALVE BODY marked Hot is installed in the left Mtg. hole,
VALVE BODY marked Cold in the right when facing front of fitting.
Maximum mounting thickness is 1-1/4".
O-R NG