Braun 2776 User manual

Cruzer3 2776 MN KURTZ DESIGN 12.07.05
F
ormat
85
x
205
cruZer2
www.braun.com/register
c
r
u
Z
e
r
2
2776
5733307_Cruzer_2776 Seite 11 Dienstag, 21. November 2006 9:41 09

2
Cruzer2 2776 MN Explo+Inuse KURTZ DESIGN 12.07.05
a
1
7
2
3
5
4a
4
4b
b
90°
90°
1
2
6
c
r
u
Z
e
r
2
5733307_Cruzer_2776 Seite 2 Dienstag, 21. November 2006 9:41 09

3
Cruzer2 MN Inuse 2 KURTZ DESIGN 12.07.05
c
d
f
g
e
180°
1
2
5733307_Cruzer_2776 Seite 3 Dienstag, 21. November 2006 9:41 09

4
5733307_Cruzer_2776 Seite 4 Dienstag, 21. November 2006 9:41 09

5
5733307_Cruzer_2776 Seite 5 Dienstag, 21. November 2006 9:41 09

6
546
2
13
5733307_Cruzer_2776 Seite 6 Dienstag, 21. November 2006 9:41 09

7
5733307_Cruzer_2776 Seite 7 Dienstag, 21. November 2006 9:41 09

8
English
Our products are designed to meet the highest standards of
quality, functionality and design. We hope you entirely enjoy
your new Braun shaver.
Warning
Your shaver is provided with a special cord set with an
integrated Safety Extra Low Voltage power supply. Do not
exchange or manipulate any part of it. Otherwise there is risk
of electric shock.
Description
1 Foil protection cap
2 Shaver foil
3 Cutter block
4 Styler
4a Wide shaper (28 mm)
4b Narrow shaper (14 mm)
5 Charginglight
6 On/off switch
7 Special cord set
Charging
The best environmental temperature for chargingis between
15 °C and 35 °C.
• Usingthe special cord set, connect the shaver to an
electrical outlet with the motor switched off.
• When chargingfor the first time, leave the shaver to
charge continuously for 4 hours. The green charging
light (5) shows that the shaver is beingcharged. When
the battery is fully charged, the charginglight intermit-
tently blinks on and off. This indicates that the battery
maintains its full capacity.
• A full charge provides 30 minutes of cordless shaving
time dependingon your beard growth.
• Once the shaver is completely charged, discharge the
shaver through normal use. Then recharge to full ca-
pacity. Subsequent charges will take about 1 hour.
• Maximum battery capacity will only be reached after
several charging/dischargingcycles.
• If the rechargeable batteries are discharged, you may
also shave by connectingthe shaver to an electrical
outlet via the special cord set.
Shaving
Remove the foil protection cap (1).
Activate the on/off switch (6). The floatingfoil frame
automatically adapts to your skin surface for a close,
smooth shave.
For pre-shavingafter a few days of not havingshaved, use
the wide shaper (4a) to pre-cut longhairs. For a close,
smooth shave, finish with the foil.
5733307_Cruzer_2776 Seite 8 Dienstag, 21. November 2006 9:41 09

9
Using the styler
• The wide shaper (4a) evenly cuts and trims larger areas
(c): Ideal for shapingsideburns, moustaches and partial
short beards. Press the blue rib to push out the styler (4).
• The narrow shaper (4b) precisely defines lines and
edges (d): Ideal for precise contouring. To use the
narrow shaper, push out the styler and turn it 180°.
• Frequent use of the styler may reduce the battery
capacity.
Cleaning
This appliance is suitable for cleaningunder an open
water tap.
Warning: Detach the hand-held part from the power
supply before cleaningit in water.
Regular cleaningensures better shavingperformance.
Rinsingthe shavinghead after each shave under running
water is an easy and fast way to keep it clean:
• Switch the shaver on (cordless) and rinse the shaving
head under hot runningwater (e). A natural based soap
may also be used provided it contains no particles or
abrasive substances. Rinse off all foam and let the
shaver run for a few more seconds.
• Next, switch off the shaver, remove the shaver foil and
the cutter block. Then leave the disassembled shaving
parts to dry.
Alternatively, you may clean the shaver usingthe brush
provided (f):
• Switch off the shaver. Remove the shaver foil.
• Usingthe brush, clean the cutter block and the inner
area of the shaver head. However, do not clean the
shaver foil with the brush as this may damage the foil.
Keeping your shaver in top shape
About every four weeks, clean the cutter block with Braun
cleaningagents. Put a drop of light machine oil onto the
shapers (4a, 4b) and the shaver foil (g).
Replacing the shaving parts
To maintain 100% shavingperformance, replace your foil
and cutter block at least every 18 months or when worn.
Tips for the perfect shave
• We recommend that you shave before washing, as
the skin tends to be slightly swollen after washing.
• Hold the shaver at right angles (90°) to the skin (b).
Stretch the skin and shave against the direction of
beard growth.
• To maintain 100% shavingperformance, replace your
foil and cutter block at least every 18 months or when
worn.
5733307_Cruzer_2776 Seite 9 Dienstag, 21. November 2006 9:41 09

10
Change both parts at the same time for a closer shave with
less skin irritation.
(Shaver foil and cutter block: 2000 series)
Preserving the batteries
In order to maintain the optimum capacity of the recharge-
able batteries, the shaver has to be fully discharged (by
shaving) every 6 months approximately. Then recharge
the shaver to full capacity. Do not expose the shaver to
temperatures higher than 50 °C for extended periods of
time.
Environmental notice
This product contains rechargeable batteries. In the
interest of protectingthe environment, please do not
dispose of the product in the household waste at the
end of its useful life. Disposal can take place at a Braun
Service Centre or at appropriate collection points provided
in your country.
Subject to change without notice.
This product conforms to the European Directives
EMC 89/336/EEC and Low Voltage 73/23/EEC.
For electric specifications, see printingon the special cord
set.
5-733-307/00/XI-06
Korea/GB
5733307_Cruzer_2776 Seite 10 Dienstag, 21. November 2006 9:41 09